Inhaltszusammenfassung zur Seite Nr. 1
S3.15
Multi-Hip Option
Assembly Instructions
Inhaltszusammenfassung zur Seite Nr. 2
S3.15 Multi-Hip Option Assembly Instructions � If you feel any pain or abnormal symptoms, Obtaining Service Important Safety Instructions stop your workout immediately and consult Do not attempt to service the Multi-Hip Before beginning any fitness program, see your your physician. Option yourself except for the maintenance physician for a complete physical examination. � Never operate the unit when it has been dropped tasks described in this guide. This unit does or damaged. Return the equipmen
Inhaltszusammenfassung zur Seite Nr. 3
S3.15 Multi-Hip Option Assembly Instructions Table of Contents Important Safety Instructions ....................................................................... 2 Personal Safety During Assembly ........................................................................................... 2 Obtaining Service .................................................................................................................... 2 Before You Begin .....................................................
Inhaltszusammenfassung zur Seite Nr. 4
S3.15 Multi-Hip Option Assembly Instructions 1 Before You Begin Thank you for purchasing the Multi-Hip Option. This option will add a new dimension to your strength- S3.15 training regimen. For proper installation, please read this guide thoroughly and follow the assembly instructions. Unpacking the Equipment The Multi-Hip Option is carefully tested and inspected before shipment. Precor Strength ships the unit in several pieces that require assembly. Ask for assistance during the assembly proces
Inhaltszusammenfassung zur Seite Nr. 5
S3.15 Multi-Hip Option Assembly Instructions Installation Requirements � Most fasteners are ³⁄₈ inch unless otherwise noted. To find out the length of a particular fastener, Follow these installation requirements when measure its shank (the long, narrow part beneath assembling the unit: the head). Refer to the following diagram: � Fill out and mail the warranty registration card. � Set up the Multi-Hip Option on a solid, flat surface. 2 Fastener head Preparations A smooth, flat surface under the
Inhaltszusammenfassung zur Seite Nr. 6
S3.15 Multi-Hip Option Assembly Instructions Assembly 3 Instructions Assembly of the Multi-Hip Option takes professional installers about ¹⁄₂ hour to complete. If this is the first Selector Hub time you have assembled this type of equipment, plan on significantly more time. Professional installers are highly recommended! However, if you acquire the appropriate tools, obtain Roller pad assistance, and follow the assembly steps sequentially, the process will take time, but is fairly easy. CAUTION:
Inhaltszusammenfassung zur Seite Nr. 7
S3.15 Multi-Hip Option Assembly Instructions 1. Attach the Multi-Hip to the S3.15 Important: Most fasteners are fitted to the frame or pulley, you will need to disassemble the fasteners before proceeding with each step. 2 - 2¹⁄₄" bolts A. Attach the Multi-Hip Base to the S3.15 Rear 2 - washers B Crossbar using three 1¼-inch hex head bolts three flat washers three spring washers three locknuts B. Position the Crossbrace against the S3.15 Main Base and place it on top of the Multi-Hip flange. Atta
Inhaltszusammenfassung zur Seite Nr. 8
S3.15 Multi-Hip Option Assembly Instructions 2. Assemble the Multi-Hip Important: The orientation of the Handlebar fasteners, Selector Hub the Roller Arm, and the Selector Stem is critical for the proper alignment of the Selector Hub. Assemble the 2 - 2½" bolts parts with the orientation shown in the illustration. 4 - washers A 2 - locknuts Selector Stem A. Attach the Handlebar to the Multi-Hip using two 2½-inch hex head bolts 1 - ³⁄₄" zinc buttonhead bolt four flat washers C 1 - washer two lock
Inhaltszusammenfassung zur Seite Nr. 9
S3.15 Multi-Hip Option Assembly Instructions 3. Install the Multi-Hip Cable Pulley assemblies A. Feed the tab end of the Multi-Hip Cable 130194 3½-inch Pulley (used on gray between the two 3½-inch pulleys on the Multi-Hip painted parts) Upright and attach the cable to the Selector Hub 1 - bolt using 2 - shoulder spacers Selector Hub 1 - locknut one shaft two e-clips B. Remove the lower 3¹⁄₂-inch pulley on the Multi-Hip Upright. Feed the cable around it and reattach it 1 - shaft using 2 - e-clips
Inhaltszusammenfassung zur Seite Nr. 10
S3.15 Multi-Hip Option Assembly Instructions 4. Attach the Multi-Hip Cable to the S3.15 A. Attach the end of the Multi-Hip Cable to the S3.15 Cable using one 1-inch hex head bolt one locknut B. Wrench tighten the locknut, but do not bend the flanges. C. Position the Pivoting Bracket to align the cables. If necessary, loosen the fastener securing the Pivoting Bracket to the Main Base. Retighten the fastener after aligning the cables. This completes the assembly of the Multi-Hip Option. Before usi
Inhaltszusammenfassung zur Seite Nr. 11
Precor Residential Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING 3. Warranty of all Precor products applies to residential use only and is void when products are YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE used in a nonresidential environment or installed in a country other than where sold. CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. 4. Except in Canada, Precor does not pay labor outside the Unit
Inhaltszusammenfassung zur Seite Nr. 12
Inhaltszusammenfassung zur Seite Nr. 13
PLACE STAMP HERE Precor Incorporated 20031 142nd Avenue NE PO Box 7202 Woodinville, WA 98072-4002 RET. Thank You and Welcome to Precor To allow us to serve you better, please take a few moments to complete and return your warranty registration. YOU MAY ALSO REGISTER ONLINE AT www.precor.com/warranty If you have questions or need additional information, contact your local dealer or call Precor Customer Support at 800-347-4404. Fold along dotted line and tape closed before mailing.
Inhaltszusammenfassung zur Seite Nr. 14
Please detach and mail in the warranty registration within ten days of purchase. TELL US ABOUT YOUR NEW PRECOR PRODUCT Product Date of Serial Purchase: Number: The serial number is located on the shipping box and on the product. Month Day Year Purchased from: Dealer Name Please indicate the type of product purchased: ® TM ❑ Elliptical Fitness CrossTrainer (EFX ) ❑ StretchTrainer ❑ Treadmill ❑ Cycle ❑ Strength Training System ❑ Stair Climber TELL US ABOUT YOU ❑ Mr. ❑ Mrs. ❑ Ms. First Name Middl
Inhaltszusammenfassung zur Seite Nr. 15
Inhaltszusammenfassung zur Seite Nr. 16
S3.15 Multi-Hip Option Specifications Length: 32 inches (81 cm) Height: 46 inches (115 cm) Width: 30 inches (75 cm) Shipping weight: 51 lb (23 kg) Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Precor is a registered trademark of Precor Incorporated. Specifications subject to change without notice. Copyright 2006 Precor Incorporated. www.precor.com S3.15 Multi-Hip Option Literature Kit 49452-101 NOTICE: S3.15 Multi-Hip Option Assembly Instructions 49453-10
