Inhaltszusammenfassung zur Seite Nr. 1
SUPER® STRIPPER
Operating Manual
Read before use and keep safe
Table of Contents
1.0 Technical Data Page 2
2.0 Safety Page 2
3.0 Safety instructions Page 2
4.0 Maintenance Page 4
5.0 Use Page 5
6.0 Information about various floorings Page 6
7.0 Troubleshooting Page 6
8.0 Spare Parts Page 7
9.0 Schematic Page 9
10.0 Blade Selection Page 10
Inhaltszusammenfassung zur Seite Nr. 2
1.0 Technical data/technical description Power supply 110-120V AC Power consumption 2200W, 20A with current limitor Number of strokes 5000 strokes/min Sound pressure level 93 dB(A) Sound energy level 106 dB(A) Hand/Arm-Vibration 6 m/s2 Weight 220 lbs Comes with: Super ® Stripper, 2 blades, ear & eye protection and tool kit. 2.0 Safety The Sinclair Super ® Stripper is state of the art designed and meets all standard safety
Inhaltszusammenfassung zur Seite Nr. 3
3.2 Danger while working with the machine The Super ® Stripper is designed to the highest technical standards. Incorrect use can be dangerous! Use this machine only: - As instructed in this operating manual. - With the machine in perfect working order. Disturbances that could impair safety have to be eliminated at once. 3.3 Restriction of use The Super ® Stripper is exclusively for removing bonded floor covering in dry environments. It should not be used for an
Inhaltszusammenfassung zur Seite Nr. 4
4.0 Maintenance The Super ® Stripper is virtually maintenance free. The guide shaft castings require lubrication from time to time. (After approx. 1650 sq. feet). Initially the machine is fully’ lubricated and should not require any additional lubrication for the first 5000 square feet. The zirc fittings are located on each side (see diagram). 1) To Grease the gearbox on its right side, remove left wheel and bottom cover. Spin axel/gearbox to expose zirc fitting. (See Diagram 2)
Inhaltszusammenfassung zur Seite Nr. 5
Changing the driving wheels Remove the lynch-pins and pull the wheels from the axle. Do not loose the wheel key under any circumstances. 5.0 Use The Super ® Stripper removes bonded, flexible floor covering in strips. This procedure corresponds with the customary method of using a hand floor scraper. The stripper works with a steel blade at a very high frequency, minimizing vibration and noise. The Super ® Stripper is self propelled. The motor actuates both the bl
Inhaltszusammenfassung zur Seite Nr. 6
6.0 Information about various floorings CV-floorings, PVC-floorings and carpets without foam backing Cut strips of approx. 30 cm (12 inch) width. If the flooring is bonded very tight, cut strips smaller. The machine should remove the flooring without slipping wheels. Carpets with foam backing A sharp blade is essential in order to ensure the floor covering is removed together with the foam backing. Remove floorings across the width, particularly if you have any u
Inhaltszusammenfassung zur Seite Nr. 7
8.0 Spare Parts Super Stripper Pos # Pieces Description Part # 1 1 Chasis S019700 4 2 Piston Block T016228 6 10 Screw M 8x30 T014736 7 8 Cylindrical pin 8x40 T014876 8 2 Lubricating nipple T014914 9 1 Hood S014657 10 4 Screw M 10x70 T014742 11 9 Safety washer 10 mm T014861 12 2 Bushing 20x26x30 T014910 13 1 Blade holder S014655 14 1 Striking Foot S014660 15 19 Screw M 8x25 T014734 16 4 Countersink screw M 10x25 T014763 17 2 Tension pin 10x20 T014890 18 2 Piston Rod T015132
Inhaltszusammenfassung zur Seite Nr. 8
59 1 Motor bracket T016860 60 24 Safety washer 8mm D014860 61 6 Elastic stop nut M8 D014816 63 1 Drive belt 187 L 100 T014937 64 1 Handle Bracket T015378 65 1 Handle Angle Brace T015051 66 1 Handle 88 T016075 67 1 Electrical short cord T014974 68 2 Cable Clip T015427 69 2 Nut T014810 70 2 Square nut T017605 71 2 Cyl Screw 8x45 T014739 72 1 Power cord w/plug T014971 73 1 Belt pulley ZZ 24 - large T015155 74 1 Belt pulley ZZ 12 - small T015156 75 1 Locknut M 10 T014820 76 2 Green w
Inhaltszusammenfassung zur Seite Nr. 9
9
Inhaltszusammenfassung zur Seite Nr. 10
TURBO, EXTRO, SUPER, BRAVO, DURO & ECO STRIPPER 10
Inhaltszusammenfassung zur Seite Nr. 11
SUGGESTED BLADE SELECTION BRAVO/DURO/ECO STRIPPER #10-4906 8”Rigid. Our standard blade for removal of vinyl, carpet, adhesive, etc. Bevel edge of blade should be up for concrete and down for wood sub-surfaces. Precutting of carpet and vinyl needed. #10-4904 8”Flexible. Same as above, yet for uneven concrete surfaces and some soft foam back carpet. #10-4907T 8”Tile Blade. For use on VAT and VCT tile. Prevents tile from jamming in between blade and blade holder. A must for til
Inhaltszusammenfassung zur Seite Nr. 12
STANDARD WARRANTY SINCLAIR EQUIPMENT COMPANY’S tools are warranted to be free of defects in workmanship and materials for a period of one year from the date of original purchase. Should any trouble develop during this one year period, return the complete tool, freight prepaid, to SINCLAIR’S authorized Service Center. If inspection shows the trouble is caused by defective workmanship or materials, SINCLAIR EQUIPMENT COMPANY will repair, or, at its option, replace without charge.
Inhaltszusammenfassung zur Seite Nr. 13
13
