Inhaltszusammenfassung zur Seite Nr. 1
Gas Dryer Installation Instructions
Canadian Electric Dryer Installation Instructions
Instructions pour l'installation de la sécheuse a gaz
(É.-U. et Canada) et électrique (Canada uniquement)
Table of Contents Table des matières
DRYER SAFETY ................................................................2 SÉCURITÉ DE LA SÉCHEUSE ........................................18
INSTALLATION REQUIREMENTS ....................................4 EXIGENCES D'INSTALLATION ...............................
Inhaltszusammenfassung zur Seite Nr. 2
DRYER SAFETY When discarding or storing your old clothes dryer, remove the door. 2
Inhaltszusammenfassung zur Seite Nr. 3
3
Inhaltszusammenfassung zur Seite Nr. 4
INSTALLATION REQUIREMENTS Tools needed for gas installations: TOOLS AND PARTS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed for all installations: 8" (203 mm) or 10" 8" (203 mm) or 10" (254 mm) pipe wrench (254 mm) adjustable wrench (for gas connections) Flat-blade screwdriver Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Pipe-joint compound resistant to LP gas
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION CLEARANCES Optional Equipment: (Not supplied with dryer) The location must be large enough to allow the dryer door Refer to your “Use and Care Guide” for information about to open fully. accessories available for your dryer. DRYER DIMENSIONS LOCATION REQUIREMENTS Dryer with extended back: Dryer with flat back: Back view: You will need: ■ A location allowing for proper exhaust installation. See “Venting Requirements”. ■ A separate 15 or 20-amp circuit needed for gas dryers and
Inhaltszusammenfassung zur Seite Nr. 6
Spacing for recessed area or closet installation ELECTRIC DRYER All dimensions show recommended spacing allowed, with tested POWER HOOKUP- CANADA ONLY spacing of 0" (0 mm) clearance on sides and rear. ELECTRICAL REQUIREMENTS ■ Additional spacing should be considered for ease of installation and servicing. ■ Additional clearances might be required for wall, door, and floor moldings. ■ Additional spacing should be considered on all sides of the dryer to reduce noise transfer. ■ For closet i
Inhaltszusammenfassung zur Seite Nr. 7
GROUNDING INSTRUCTIONS GROUNDING INSTRUCTIONS � For a grounded, cord-connected dryer: � For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. by providing a path of least resistance for electric current.
Inhaltszusammenfassung zur Seite Nr. 8
LP Gas Conversion: BURNER INPUT REQUIREMENTS Elevations above 10,000 ft. (3,048 m): IMPORTANT: Conversion must be made by a qualified ■ When installed above 10,000 ft. (3,048 m) a 4% reduction technician. of the burner Btu rating shown on the model/serial number No attempt shall be made to convert the dryer from the gas plate is required for each 1,000 ft. (305 m) increase in specified on the model/serial rating plate for use with a different elevation. gas without consulting your gas co
Inhaltszusammenfassung zur Seite Nr. 9
Rigid metal vent: 2. Screw in leveling legs ■ Recommended for best drying performance and to avoid crushing and kinking. Flexible metal vent: (Acceptable only if accessible to clean) ■ Must be fully extended and supported in final dryer location. Diamond ■ Remove excess to avoid sagging and kinking that may diamond marking result in reduced airflow and poor performance. marking ■ Do not install in enclosed walls, ceilings, or floors. 3 ■ The total length should not exceed 7 /4 ft. (2.4 m). N
Inhaltszusammenfassung zur Seite Nr. 10
Clamps: Optional exhaust installations: ■ Use clamps to seal all joints. ■ Exhaust vent must not be connected or secured with screws or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape. ■ Exhaust Cover Kit (to cover unused exhaust holes): Part Number W10186596 - all models ■ Bottom Exhaust Kit- Part Number 8212503 Vent products can be purchased from your dealer. For more information, see “Assistance or Service” section in your “Use and Care Gui
Inhaltszusammenfassung zur Seite Nr. 11
Alternate installations for close clearances Determine vent path: Venting systems come in many varieties. Select the type best ■ Select route that will provide straightest and most direct for your installation. Two close-clearance installations are shown. path outdoors. Refer to the manufacturer’s instructions. ■ Plan installation to use fewest number of elbows and turns. ■ When using elbows or making turns, allow as much room as possible. ■ Bend vent gradually to avoid kinking. ■ Use as few
Inhaltszusammenfassung zur Seite Nr. 12
A INSTALL ENT SYSTEM v 2. Plan pipe fitting connection 1. Install exhaust hood 12" min. D (305 mm) C A B 12" min. A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow (305 mm) B. 3/8" dryer pipe D. 3/8" pipe-to-flare adapter fitting Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood. A combination of pipe fittings must be used to connect dryer to existing gas line. A recommended connection is shown. Your connection may be different, accordin
Inhaltszusammenfassung zur Seite Nr. 13
Attach short hose and 2. Attach long hose to dryer fill 5. “Y” connector valve and tighten coupling 3 3 /4" (95 mm) 11" (279 mm) Fig. A Fig. B If space permits, attach the brass female end of the “Y” connector to the cold water faucet. See figure A. Attach other end of long hose to fill valve at bottom of dryer If “Y” connector cannot be attached directly to the cold water back panel. Screw on coupling faucet, the short hose must be used. See figure B. Attach by hand until it is sea
Inhaltszusammenfassung zur Seite Nr. 14
CONNECT vENT LEvEL DRYER 1. Level Dryer 1. Connect vent to exhaust outlet Place level here Place level here Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is Check levelness of dryer from side to side. Repeat from clean. Dryer vent must fit over dryer exhaust outlet and inside front to back. exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp. NOTE: The dryer must be level for the moisture
Inhaltszusammenfassung zur Seite Nr. 15
COMPLETE INSTALLATION REERSE DOOR SWING v CHECKLIST You can change your door swing from a right-side opening to a left-side opening, if desired. Check that all parts are now installed. If there is an extra q part, go back through steps to see what was skipped. 1. Place a towel or soft cloth on top of dryer or work space to avoid damaging the surface. Check that you have all of your tools. q Dispose of/recycle all packaging materials. q Remove the door assembly Be sure the water faucet
Inhaltszusammenfassung zur Seite Nr. 16
Reverse the strike 4. Install the two hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge 1. Remove the door strike (A) from the dryer door opening. to the front panel. 2. Remove the cosmetic screw (B) opposite the door strike (A). 5. Install scr ews in top hinge holes in the door. Do not tighten screws. Leave approximately 1/4" (5 mm) of screw exposed. B A A. Door strike B. Cosmetic screw 3. Reinstall the door strike and co
Inhaltszusammenfassung zur Seite Nr. 17
DRYER RESULTS TROUBLESHOOTING Clothes are not drying satisfactorily, drying times are DRYER OPERATION too long, or load is too hot ■ Is the lint screen clogged with lint? Dryer will not run Lint screen shold be cleaned before each load. ■ Has a household fuse blown, or has a circuit breaker tripped? There may be two household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse or reset the
Inhaltszusammenfassung zur Seite Nr. 18
SÉCURITÉ DE LA SÉCHEUSE Pour mettre l’ancienne sécheuse au rebut ou pour la remiser, enlever la porte. 18
Inhaltszusammenfassung zur Seite Nr. 19
19
Inhaltszusammenfassung zur Seite Nr. 20
EXIGENCES D'INSTALLATION OUTILLAGE ET PIÈCES Outils nécessaires pour les installations à gaz : Rassembler les outils et composants nécessaires avant d’entreprendre l’installation. Lire et observer les instructions fournies avec chacun des outils de la liste ci-dessous. Outils nécessaires à toutes les installations : Clé à tuyau de 8" (203 mm) Clé à mollette de 8" (203 mm) ou 10" (254 mm) ou 10" (254 mm) (pour le raccordement au gaz) Tournevis à lame plate Clé à molette avec ouverture jusq
