Bedienungsanleitung Maytag Bottom FreezerMCS 16021937

Inhaltszusammenfassung zur Seite Nr. 1

JENN-AIR BOTTOM FREEZER REFRIGERATOR
USER
USER
GUIDE GUIDE
ABLE OF CONTENTS
T
Introduction...........................................................................2 Freezer Features ................................................................13
Important Safety Information............................................3 Automatic Ice Maker ......................................................13
Installation Instructions...................................................4-9 Drawers...........

Inhaltszusammenfassung zur Seite Nr. 2

INSTALLATION INSTRUCTIONS These instructions were provided to aid SELECTING THE BEST CAUTION: you in the installation of your refrigerator. To avoid damage to walls and flooring, LOCATION protect soft vinyl or other flooring Allow for a free flow of air through with cardboard, rugs or other MEASURING THE the front base grille. protective material. OPENING Install the refrigerator where the room temperature will not go below 1 1. Unplug power cord from power A ⁄2" of air space should be provi

Inhaltszusammenfassung zur Seite Nr. 3

3 • Trim will slide up approximately ⁄4" HOW TO REVERSE HOW TO INSTALL AND and release from door. REFRIGERATOR DOOR REMOVE HANDLES 8. Rotate door panel In some cases, handles may need to be Note: 180° and tape in place. removed to transport unit through tight spaces, reverse doors, or install panels. When working directly on door, lay 9. Remove top door 1 the interior side of the door down extension with ⁄4" hex Some models may come with handles head driver. Flip door flat, nonabrasive surface.

Inhaltszusammenfassung zur Seite Nr. 4

INSTALLATION INSTRUCTIONS, CONT. HOW TO REPLACE THE HOW TO INSTALL AND WHAT IF I AM DOOR AND HINGES REMOVE PANELS INSTALLING RAISED (SOME MODELS) 1. Install center hinge with Phillips PANELS? screws. Please see recommended dimensions for 3 1 WARNING: 2. Install stabilizing brackets with ⁄8" hex paneling. All panel holes are ⁄4" diameter. head screws. To avoid personal injury or property 2.879" 7.3 cm damage, fresh food panel should not 3.Replace center weigh more than 30 lbs (14 kgs) and hinge p

Inhaltszusammenfassung zur Seite Nr. 5

3. Pull drawer open to full extension. 3. Lower door into final position. HOW TO REMOVE AND 4. Remove Phillips screw from each side 4. Replace and tighten Phillips screws INSTALL THE PULLOUT of rail system. (Some models) that were removed from each side of DRAWER rail system. WARNING: To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before removing doors. After replacing doors, connect power. CAUTION: To avoid possible injury, product, o

Inhaltszusammenfassung zur Seite Nr. 6

INSTALLATION INSTRUCTIONS, CONT. 4. Place end of copper tubing into water MATERIALS NEEDED HOW TO CONNECT valve inlet port. Shape tubing slightly – 1 ⁄4" outer diameter flexible copper DO NOT KINK – so that tubing feeds THE WATER SUPPLY tubing straight into inlet port. 1 Shut-off valve (requires a ⁄4" hole to WARNING: be drilled into water supply before valve attachment) To reduce the risk of injury or death, follow basic precautions, Adjustable wrench including the following: 1 ⁄4" he

Inhaltszusammenfassung zur Seite Nr. 7

4. Turn stabilizing legs (C) clockwise HOW TO LEVEL YOUR until firmly against floor. REFRIGERATOR 5. Turn front roller adjustment screws (A) 2 to 3 times counterclockwise, so If your refrigerator requires an ice maker that full weight of unit rests on water supply connection, complete stabilizing legs (C). connection instructions on page 8 before leveling your refrigerator. A CAUTION: To protect personal property or unit from damage, observe the following: C Protect soft vinyl or other floorin