Bedienungsanleitung Life Fitness M051-00K61-C131

Inhaltszusammenfassung zur Seite Nr. 1

INTEGRITY AND CLUB SERIES CROSS-TRAINERS
CLSX & CSX ASSEMBLY INSTRUCTIONS
M051-00K61-C131

Inhaltszusammenfassung zur Seite Nr. 2

Congratulations... and welcome to the world of The following Component List and the step-by-step assembly procedures have been developed to make the set-up of the Cross-Trainer as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Cross-Trainer. 1

Inhaltszusammenfassung zur Seite Nr. 3

IMPORTANT SAFETY INSTRUCTIONS! â DO NOT locate the Cross-Trainer outdoors, near swimming pools, or in areas of high humidity. â DO NOT operate your Cross-Trainer if it has been dropped, damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services at the number in the Operation Manual. â DO NOT locate the Cross-Trainer any closer than 30 inches (76 cm) to a television set. â DO NOT locate additional Cross-Trainers any closer than 42 inches (107 c

Inhaltszusammenfassung zur Seite Nr. 4

COMPONENT LIST # Part Description Qty. # Part Description Qty. Hex Socket Head Cap Screw Phillips Pan Head Screw 1 3/8-16 X 1” 8 2 #8-18 X 3/4” 4 0017-00101-1645 0017-00101-1744 Phillips Pan Head Pointed Screw Console Assembly 3 #8-18 X 3/4” 18 4 1 (shipped separately) 0017- 00101-1242 5 Front Monocolumn Cover 1 6 Back Monocolumn Cover 1 Flat Washer 7 Console Support Assembly 1 8 2 0017-00104-0192 9 Left Front Cover 1 10 Right Front Cover 1 11 Left User Arm Assembly 1 12 Right User Arm Assembly

Inhaltszusammenfassung zur Seite Nr. 5

HARDWARE FLAT WASHER (#8) INTERNAL TOOTH LOCK WASHER (#18) #8-18 X 3/4”PHILLIPS PAN HEAD #8 -18 X 10 PHILLIPS PAN HEAD SCREW (#2) POINTED SCREW (#3) 3/8 -16 X 1” HEX SOCKET HEAD CAP SCREW (#1) GROMMET (#20) CAP SCREW T -27 (#21) 4

Inhaltszusammenfassung zur Seite Nr. 6

IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT. IMPORTANTES! NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION. 1. Before proceeding, familiarize yourself with the parts of the Cross-Trainer and make sure that you have received all the 3 items described in the Component List. 9 2. Locate the left and right

Inhaltszusammenfassung zur Seite Nr. 7

8. Attach the 4-PIN (4P) and 16-PIN (16P) CONNECTORS to the 4P corresponding JACKS on the back of the CONSOLE ASSEMBLY (4). 16P 9. Feed any excess WIRE HARNESS (E) down into the CONSOLE SUPPORT ASSEMBLY (7). Secure the CONSOLE ASSEMBLY (4) to the 4 CONSOLE SUPPORT ASSEMBLY using four PHILLIPS PAN HEAD 21 SCREWS (2). Tighten the SCREWS securely. 19 CAUTION: Do not over-tighten the PHILLIPS PAN HEAD SCREWS (2). 23 CAUTION: Be careful not to pinch the WIRE HARNESS (E) when 2 22 3 assembling the CO

Inhaltszusammenfassung zur Seite Nr. 8

PRE-OPERATION CHECKLIST 3 Ensure that all fasteners are tight. 3 Make sure the Cross-Trainer is properly leveled and stable. (Refer to the Cross-Trainer model’s corresponding Operation Manual.) 3 Ensure that the Leveler Jam Nuts are tight. (Refer to the Cross-Trainer model’s corresponding Operation Manual.) 3 Read the entire Operation Manual before using the Cross-Trainer. LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE 3 Vérifiez si tous les dispositifs de fixation sont serrés 3 V