Bedienungsanleitung Grizzly H8219

Inhaltszusammenfassung zur Seite Nr. 1

MODEL H8219
AIR ORBITAL SANDER
INSTRUCTION MANUAL
COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JM9840 PRINTED IN CHINA

Inhaltszusammenfassung zur Seite Nr. 2

����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������

Inhaltszusammenfassung zur Seite Nr. 3

SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica

Inhaltszusammenfassung zur Seite Nr. 4

7. AVOID ENTANGLEMENTS. Do not 16. DO NOT FORCE TOOL. It will do wear loose clothing, gloves, neck- the job better and safer at the rate ties, rings, bracelets, or other jewel- for which it was designed. ry, which may get caught in moving 17. CHECK FOR DAMAGED PARTS parts, when operating this tool. Wear BEFORE USING. Check for bind- a protective hair covering to contain ing and alignment of parts, broken long hair. parts, part mounting, loose bolts, 8. USE CORRECT AIR PRESSURE. and an

Inhaltszusammenfassung zur Seite Nr. 5

INTRODUCTION Foreword Specifications The specifications, details, and No Load Speed.........................8,000 RPM photographs in this manual represent Air Consumption...............................6 CFM 1 the Model H8219 as supplied when the Air Inlet..................................................... ⁄4" manual was prepared. However, owing to Required PSI.....................................90 PSI Grizzly’s policy of continuous improvement, changes may be made at any time with no Specif

Inhaltszusammenfassung zur Seite Nr. 6

OPERATIONS Attaching Sandpaper 1. DISCONNECT THE SANDER FROM THE AIR SUPPLY! 1 2. Install the ⁄4" NPT male quick-connect fitting into the air inlet. 3. The sanding pad for the Model H8219 1 1 measures 6 /2" X 3 /2". New sandpaper sheets can be obtained by cutting down a single sheet or a piece from a roll. Read the manual before operation. 1 Cut at least 2 /2" extra for the length to Become familiar with this tool, its fasten it properly. safety instructions, and its operation be

Inhaltszusammenfassung zur Seite Nr. 7

EYE INJURY LUNG/EAR HAZARD! INJURY HAZARD! Wear protective Wear protective equipment when equipment when using this tool. using this tool. ACCIDENTAL Using the Sander START HAZARD! Disconnect before 1. Plug the tool into compressed air regu- service or tool lated at 90 PSI. changes. AIR PRESSURE 2. Hold the sander firmly and press the HAZARD! throttle lever (Figure 3) to turn it ON. Never exceed max PSI rating for tool. 3. Turn the regulator knob (Figure 3) to adjust the speed of th

Inhaltszusammenfassung zur Seite Nr. 8

H8219 PARTS LIST �� �� �� �� �� �� �� �� �� �� � � �� � � �� � � �� �� � �� �� � �� � �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8219001 MOTOR HOUSING 24 PH8219024 ROTOR SHAFT 2 PH8219002 FOAM MUFFLER 25 PH8219025 GASKET 3 PH8219003 LEVER PIN 26 PH8219026 MOUNT SCREW 4 PH8219004 COMPRESSION SPRING 27 PH8219027 LOCK WASHER 5 PH8219005 PLUNGER 28 PH8219028 BASE 6 PH8219006 AIR COUPLER 29 PH8219029 RUBBER MOUNT 7 PEC13M E-CLIP 5MM