Inhaltszusammenfassung zur Seite Nr. 1
CDX-470
Natural Sound Compact Disc Player
Random Access Programmable Play
Random-Sequence Play
Single Track/Entire Disc Repeat Play
Automatic Tape-Programming
Automatic Peak Level Searching Capability
Display Brightness Changing Capability
Remote Control Capability
Thank you for selecting this YAMAHA Compact Disc Player.
OWNER’S MANUAL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CONTENTS
Safety Instructions.................... 2
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
Connec
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY INSTRUCTIONS 1 Read Instructions – All the safety and operating 11 Power-Cord Protection – Power-supply cords should be instructions should be read before the unit is operated. routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying 2 Retain Instructions – The safety and operating particular attention to cords at plugs, convenience instructions should be retained for future reference. receptacles, and the point where they exit from the un
Inhaltszusammenfassung zur Seite Nr. 3
WARNING 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with CAUTION these requirements provides a reasonable level of Use of controls or adjustments or performance of assurance that your use of this product in a residential procedures other than those specified herein may result in environment will not result in harmful interference with hazardous radiation exposure. other electronic d
Inhaltszusammenfassung zur Seite Nr. 4
CONNECTIONS Before making any connections, switch OFF the power to Be sure that the left (“L”) and right (“R”) LINE OUT terminals • • the unit and the amplifier or other component. are connected to the corresponding (left and right) terminals Connect the “LINE OUT” terminals to the “CD” (or “AUX”) of the amplifier or other component. • terminals of the amplifier. If the amplifier does not have such If the placement of this unit causes noise to other equipment, • terminals, use the “TAPE PB” ter
Inhaltszusammenfassung zur Seite Nr. 5
IDENTIFICATION OF COMPONENTS FRONT PANEL SKIP button STOP button POWER switch Display panel PAUSE button PLAY button Disc tray PEAK button TIME display modeselect button Remote control sensor TAPE button PLAY PAUSE STOP TIME PEAK NATURAL SOUND COMPACT DISC PLAYER POWER TAPE PROG RANDOM SKIP OUTPUT LEVEL REPEAT SEARCH DOWN UP OPEN/CLOSE +10 123 4 5 6 7 8 9 0 PHONES Numeric buttons OUTPUT LEVEL buttons OPEN/CLOSE button PROG button REPEAT button RANDOM button PHONES jak SEARCH button REMOTE CONTRO
Inhaltszusammenfassung zur Seite Nr. 6
LOADING THE DISC/DISC PLAY 4 1 LOGODISK 2, 3 POWER 1 3 OPEN/CLOSE 2 Label side upward OPEN/CLOSE 4 PLAY Disc tray Display information at disc play Notes After closing the disc tray by pressing the OPEN/CLOSE • 12 button, the display shows the total number of tracks and the total recorded time of the disc for a few seconds. 3 Additionally, you can close the disc tray by pressing the • Shows the track number to be played. PLAY button, a numeric button or the RANDOM button, or Shows the time dis
Inhaltszusammenfassung zur Seite Nr. 7
To stop play temporarily To stop play completely STOP PAUSE * To resume play, press the PAUSE button again or press the PLAY button. To play a desired track on the disc DIRECT PLAY SKIP PLAY To play from the beginning of the track following the one now Select a desired track using the numeric button. • playing SKIP +10 1 2 34 5 6 7 8 90 To play from the beginning of the track now playing • SKIP The selected trak number is displayed To play from the beginning of the track before the one now • pl
Inhaltszusammenfassung zur Seite Nr. 8
Selecting time displays You can select any of the four time displays by pressing the TIME display modeselect button. Elapsed time of the track now playing Total remaining time on the disc ˆ TIME Remaining time of the track now playing Total disc play time ` ´ Note The remaining time will not be displayed for track number ` 25 or higher. Changing brightness of the display If desired, you can change brightness of the display in three degrees by pressing the MODE button. Normal illumination MODE
Inhaltszusammenfassung zur Seite Nr. 9
RANDOM-SEQUENCE PLAY You can have the unit play the tracks on a disc in a random sequence selected by the unit’s microcomputer. Notes To perform random-sequence play This feature will not function during programming, or during • programmed play. If the POWER is switched off when the random-sequence • RANDOM play mode is functioning, when the POWER is switched on again, the unit will begin the random-sequence play automatically. (This feature is available for timer play.) If the SKIP button is p
Inhaltszusammenfassung zur Seite Nr. 10
PROGRAM PLAY You can enjoy listening to your favorite tracks in any desired order using programmed play. As many as 25 tracks can be programmed for a disc. 24 1 LOGODISK 3 1 Stop the unit. 3 Select the desired track. +10 1 2 34 5 6 7 8 90 STOP * Repeat step 3 to set more programs. You can select the same track again. 2 4 PLAY PROG Notes Display information during program play In step 2, if “P-01” does not appear in the display, press the • TIME display mode-select button. If, during programming
Inhaltszusammenfassung zur Seite Nr. 11
To check programmed data To stop program play 1. If the unit is in the play mode, press the STOP button. Press the STOP button. The first track number programmed 2. Press the PROGbutton. will be displayed. 3. Each time the SKIP button is pressed, the track To resume play, press the PLAY button. Play will begin from numbers and sequential order of the programmed tracks the beginning of the program. can be checked one after another. The display of the track number can be returned (sequentially
Inhaltszusammenfassung zur Seite Nr. 12
TRACK PROGRAMMING FOR RECORDING TO TAPE This convenient feature can be used to program tracks on a disc for recording to tape. By only memorizing the tape’s total possible recording time, the unit will automatically program tracks or help you to program tracks so they will fit onto the tape with the least amount of unrecorded space remaining at each end of the tape. Additionally, this function will insert sufficient time space between programmed tracks automatically so that the tape deck can p
Inhaltszusammenfassung zur Seite Nr. 13
Manual tape-programming n This is for recording desired tracks in any desired order onto a tape. 2 6, 7 4, 7 LOGODISK 3, 5 1 Follow steps 1 – 3 on page 12. 5 Select the track numbers (to be recorded on side B) in the desired order. +10 1 2 34 5 6 7 8 90 2 PROG 6 Begin recording on the tape deck and press the PLAY button on this unit at the same time. 3 Select the track numbers (to be recorded on side A) in the desired order. 7 The unit will pause at the end of side A of the tape. Turn the tap
Inhaltszusammenfassung zur Seite Nr. 14
Random sequential tape-programming n The unit will automatically program tracks in random sequential order for recording to tape. 3, 4 4 LOGODISK 2 Notes Because the programmed data changes every time the • 1 Follow steps 1 – 3 on page 12. RANDOM button is pressed, the amount of time remaining at the end of the tape also changes accordingly. If the tape’s length is not enough, all tracks cannot be • 2 RANDOM programmed. In this case, exchange the tape for a longer one. In step 2, you can check
Inhaltszusammenfassung zur Seite Nr. 15
Automatic searching of the peak level on a disc This convenient feature automatically searches the part on a disc where the source level peaks, and next plays the part repeatedly. For recording to tape, this feature is very helpful to adjust the recording level on the tape deck. 2 1 LOGODISK To cancel the peak level searching function Press the STOP button. (However, some other buttons can 1 Stop the unit. also be used to cancel this function.) STOP Notes Even if the peak level searching is per
Inhaltszusammenfassung zur Seite Nr. 16
30° NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range Remote control sensor Within approximately 7 m (23 feet) Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes Use only AA, R6, UM-3 batteries for replacement. • Be sure the polarities are correct. (See the illustration inside Notes • the battery compartment.) There
Inhaltszusammenfassung zur Seite Nr. 17
TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM PROBABLE CAUSE REMEDY The player does not switch ON when the The power cord is not connected or not Securely connect the power cord. POWER switch is p
Inhaltszusammenfassung zur Seite Nr. 18
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFO
