Inhaltszusammenfassung zur Seite Nr. 1
882i
Sonic MaxiMizer
User Guide and Reference Manual
Inhaltszusammenfassung zur Seite Nr. 2
For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference. Carefully observe all warnings, precautions and instructions on the appliance and described in the operating instructions supplied with the appliance. inSTaLLaTion Water and Moisture - Do not install the appliance near water: for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Heat - Do not in
Inhaltszusammenfassung zur Seite Nr. 3
TaBLe oF conTenTS Important Safeguards ……………………………………………………………………………………………… BBE Process Explained …………………………………………………………………………………………… Product Description ………………………………………………………………………………………………… 4 Applications/Set Up ………………………………………………………………………………………………… 4 Front Panel Controls ……………………………………………………………………………………………… 5 Rear Panel Connections …………………………………………………………………………………………… 6 Applications …………………………………………………………………………………………………… 7-1 Specifications …………………………………………………………………………………………………… 14 Servic
Inhaltszusammenfassung zur Seite Nr. 4
ProdUcT deScriPTion The BBE 882i is a dual channel, single rack space device for use in +4dBu balanced line applica- tions. Each of the two independent channels has a Lo Contour control, Process control and a 5 segment LED output level meter. A single function button switches the BBE process on or off in both channels, which is useful for comparing the processed sound to the unprocessed sound. An LED next to the function button glows green when the BBE process is on and yellow when the proce
Inhaltszusammenfassung zur Seite Nr. 5
FronT PaneL conTroLS � � � � � � 1. LED DISPLAY: The LED display is used to indicate the output signal level of the BBE 882i. Each number on the front panel corresponds to the output signal level, measured in decibels. Example: The “+10” indicates a 10dBu signal level, “0” refers to 0dBu, and so on. Once an input signal level has been established, increasing the BBE PROCESS and LO CONTOUR will increase the output signal and cause more LEDs to illuminate. The Clip LED monitors the input sig
Inhaltszusammenfassung zur Seite Nr. 6
rear PaneL connecTionS � � � � � 1. AC POWER CORD INLET: Plugs into AC power receptacle. U.S., Canada and Japan Models, 100-120Vac, 50/60Hz. All other models, 220~240Vac, 50/60Hz. 2. FUSE: Insert a flat blade screwdriver into the fuse holder located in the bottom portion of the AC Power Cord inlet. Carefully pry the fuse holder free from its compartment to access fuse. (Note: For all models, replace with 250VAC, .2A slowblow type fuse.) 3. OUTPUT: The output of the BBE 882i can be taken fro
Inhaltszusammenfassung zur Seite Nr. 7
LiVe aPPLica Tion: non-Po Wered Mixer Connect the BBE 882i to the output of the mixing console. The output of the BBE will drive either a crossover or a power amplifier directly. MAIN OUTPUTS POWER AMP 7
Inhaltszusammenfassung zur Seite Nr. 8
LiVe aPPLica Tion: Po Wered Mixer There are a couple of ways to configure the BBE 882i into a powered mixer. The ideal method would be into “Pre-Amp Out/Power Amp In” section of the console. If your console does not have this option, use the main or channel insert points. PRE PWR MAIN AMP AMP OUT OUT IN TIP/RING/SLEEVE (TRS) INSERT POINT ON MAIN OR INDIVIDUAL CHANNELS 8
Inhaltszusammenfassung zur Seite Nr. 9
recording The BBE 882i can be utilized in the recording studio on individual instruments of on groups on instruments to improve the sound quality. MIXER KEYBOARD OR OTHER INSTRUMENT MULTI-TRACK TAPE RECORDER OR DAW INPUT
Inhaltszusammenfassung zur Seite Nr. 10
MaSTering or dUBBing Use the BBE 882i for mastering the recording. Even if the BBE Process has been used on indi- vidual tracks, an improvement on the total mix will be noticed. MIXER MULTI-TRACK RECORDER - CASSETTE, REEL-TO-REEL, DAW MASTERING DECK - DAT, CASSETTE, REEL-TO-REEL, DAW, ETC. 10
Inhaltszusammenfassung zur Seite Nr. 11
indiVidU aL inSTr UMenTS Use the BBE 882i in the effects loop or the main output of a guitar preamp. For keyboards, the output of the sub-mixer will be the ideal location. INSTRUMENT PREAMP MAIN OUTPUTS POWER AMP 11
Inhaltszusammenfassung zur Seite Nr. 12
SoUnd conTracT orS The BBE 882i will accept the output level of most sound contractor type mixers. PAGING/MUSIC PREAMP POWER AMP 1
Inhaltszusammenfassung zur Seite Nr. 13
dJ aPPLica Tion Connect the BBE 882i into the processor loop of a pre-amplifier/mixer and hear the music come alive! MAIN OUTPUTS POWER AMP 1
Inhaltszusammenfassung zur Seite Nr. 14
SPeciFica TionS process mode Program controlled Frequency r esponse bypass mode 10Hz to 50kHz +/-0.5dBu, 0dBu input process mode less than 0.025% at -10dBu input, 20-20kHz Thd bypass mode less than 0.002% at -l0dBu input, 20-20kHz Maximum output +23dBu (may vary due to control settings) 14.7k Ohms, balanced 1/4” TRS phone jack or input impedance XLR jack Pin #2 hot or “+” 600 Ohms, balanced 1/4” TRS phone jack or output impedance XLR jack Pin #2 hot or “+” Sensitivity -45dBu for maximum p
Inhaltszusammenfassung zur Seite Nr. 15
Ser Vice We recommend that if at all possible, a BBE Sonic Maximizer which requires service be sent to our facility in Huntington Beach, California. We request that a “RETURN AUTHORIZATION” be issued by the dealer from whom you purchased the unit. If this is not possible, call BBE Sound, Inc. directly at (714) 897-6766, exten- sion 116 to obtain a “RETURN AUTHORIZATION”. Include a copy of the bill of sale with the unit when it is shipped to BBE Sound, Inc. so that the service can be expedited
Inhaltszusammenfassung zur Seite Nr. 16
F I V E Y E A R • L I E M I 5 5 5381 Production Drive Huntington Beach, CA 92649 714-897-6766 • FAX 714-896-0736 www.bbesound.com covered by U.S. Patent 5,736,897 and other U.S. and foreign patents pending. BBE is the registered trademark of BBE Sound, Inc. rev.4 9-2010 B T B E D • W A R R A N T Y
