Inhaltszusammenfassung zur Seite Nr. 1
Operation 6030
ENGLISH
HEAT
OFF
COOL
FAN
ON
AUTO
MENU
PROG
Inhaltszusammenfassung zur Seite Nr. 2
Operation 6030 Using a TOUCH SCREEN Current Time Room Temperature Mode Slot Please take a moment to try out Switch your touch screen itself. To select a function on the Day touch screen, place your finger Fan Time on the main temp display and Switch of day give a short firm push. Try a Menu Target button "tap" of the finger or stylus. Your Temperature Program input must last long enough for Thermostat button Touch Mode the system to determine it is not Screen an accidenta
Inhaltszusammenfassung zur Seite Nr. 3
Displayed when the MENU button is pressed. MENU screen o o Calibration control Set C - F Set Day Use this to calibrate your LCD Touch this to Touch this area to set display match to another set temperature the day of the week. thermometer. display. Set Time Return Touch this area to set AM HOME the time of day. Left arrow goes back, right arrow goes forward. Temperature Swing set Filter Timer set Calibration indicator Chirp set Lock Program This shows if you Touch this to turn Touch for
Inhaltszusammenfassung zur Seite Nr. 4
PG 5 The Mode Switch must be in Configure HEAT or COOL mode to configure. Press MENU to configure the thermostat (from HOME screen). Set day of the week - Touch the Day of the week area to cycle through the days of the week to select the current day. Set time of day - Touch the Time of Day arrows to move the time selection forward or backward until it displays the current time. Touch and hold for faster setting. Backward Forward o o Set C - F display o o Touch the F and it will toggle to
Inhaltszusammenfassung zur Seite Nr. 5
PG 7 Program NOTE: 60 Second Rule-During programming, if a button is not pushed in 60 seconds, the unit will return to the home screen. Everything you have changed while programming will automatically be saved. Select HEAT with the HEAT/Cool MODE switch. Press PROGRAM to go to the programming screen. Select the day you want to program- Touch the Day of the week area to cycle through the days of the week to select the desired day. Select the time slot you want to program - Touch the Time
Inhaltszusammenfassung zur Seite Nr. 6
Manual PG 9 The 6030 has 3 manual override commands. These are accessed by touching the Current Temp Display at the HOME screen (center of screen). Target Temperature Return HOME HOLD Touch this area to set a comfortable target temp for the system to hold until you return TEMPORARY and remove HOLD. Manual Override indicator Temp Up / Temp Down arrows Shows TEMPORARY when Touch these to raise and lower you have modified the Target. the manual override Target Temp. MANUAL override screen
Inhaltszusammenfassung zur Seite Nr. 7
PG 11 Special Features Swing setting determines the temperature Swing difference in degrees from ON to OFF that the thermostat will command the HVAC system to run. With the MODE switch in HEAT or COOL, press the MENU button. Touch the SWING icon and the current setting of temp swing is shown on o the display (default at .5 ). To change the swing factor, touch the left or right arrows. The furnace will cycle more at the lower numbers as it tries to maintain your temp. When the batteries
Inhaltszusammenfassung zur Seite Nr. 8
P 13 MENU screen Heat Pump Features If you have configured your 6030 for heat pump control the MENU screen AM will display an additional icon - the HEAT PUMP ON/OFF icon. When using a heat pump with Auxiliary heat, if the heat pump cannot keep up and/or is defective, touch the MENU button, then touch PUMP OFF PUMP ON; the PUMP OFF icon will come on. The aux heat will then be HEAT PUMP ON/OFF ICON your only source of heat. When the heat pump is again operational, be sure to tur
Inhaltszusammenfassung zur Seite Nr. 9
o NOTE: Your thermostat comes from the factory calibrated to + or - 1 F actual temperature. It is an accurate instrument. If you want your thermostat to display the same temperature as another thermometer in your home, you can adjust it. o Maximum calibration is +/-6 . To change the calibration: With the switch MODE in HEAT or COOL. Press the MENU button. Press the Temp Up/Temp Down arrows to adjust the temperature reading. CALIBRATE DISPLAY ON will appear. Press HOME to save the new s
