Inhaltszusammenfassung zur Seite Nr. 1
FUJITSU MICROELECTRONICS (SHANGHAI) CO., LTD.
Unit 1501, Jin Mao Tower, 88 Century Ave., Pudong New Area, Shanghai, P.R. China
MCU-AN-500087-E-12
Tel: 61007800 Fax: 61007802
F² MC-8FX FAMILY
8-BIT MICROCONTROLLER
MB95F430 SERIES
Induction Heater Hardware
User Manual
Revision History
Version Date Comment Charge
Create.
1.0 2010-04-06 Folix
Modified:
1. System Feature;
2. MCU Pin Assignment;
3. IGBT Feature;
1.1 2010-08-11 Folix
4. Power Module;
5. IGBT Dr
Inhaltszusammenfassung zur Seite Nr. 2
Induction Heater C Library User Manual Version 1.2 Contents Revision History ................................................................................................................................... 1 1. Introduction........................................................................................................................................... 3 2. System Features .............................................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Induction Heater C Library User Manual Version 1.2 1. Introduction This document has introduced how to use the electromagnetic oven hardware. The hardware includes two PCB boards (main board and front board), a fan and a pad. MCU-AN-500087-E-12 3 / 18
Inhaltszusammenfassung zur Seite Nr. 4
Induction Heater C Library User Manual Version 1.2 2. System Features Power Control Fan Control Fan Delay Off Buzz Control Led Display Keyboard Kettle Detect Kettle Empty Detect Timing Power Off(3Hours) Constant Power Heating Constant Temperature Heating IGBT Temp Detect Plate Temp Detect IGBT Temp Higher Protect(120 ℃) Plate Temp Higher Protect(300 ℃) Kettle Empty Protect(300 ℃) Sensor Open/Short Detection Over Current Protect(18A) Over
Inhaltszusammenfassung zur Seite Nr. 5
Induction Heater C Library User Manual Version 1.2 3. System Introduce 3.1. Hardware Block Diagram Figure-1 Hardware Block Diagram The electromagnetic eddy current heating is our system theory. We use the PWM to control the IGBT to generate the heating eddy current. The fan is use to cool the IGBT. The feedback signal is used to protect the system and calculate power. 3.2. MCU Resource Usage MB95F434K Resource Usage No. Resource Usage Info Remark 1 VCC 5.0V 2 ROM 3 RAM 4 OS
Inhaltszusammenfassung zur Seite Nr. 6
Induction Heater C Library User Manual Version 1.2 3.3. MCU Pin Assignment No. Name Define Note Remark sub oscillator 1 PG2/PPG0/X1A/OUT1 LED COM1 sub oscillator 2 PG1/TRG0/ADTG/X0A/BZ/OUT0 Fan 3 VCC VCC Vcc 4 C C C 5 P60/OPAMP_P OPAMP_P Current by Resistor 6 P61/OPAMP_N OPAMP_N 7 P62/OPAMP_O P62 LED COM2 8 P12/EC0/UI/DBG P12/DBG Debug 9 P00/INT00/AN00 P00 Start IGBT 10 P01/INT01/AN01/BZ BZ Buzzer 11 P02/INT02/AN02/UCK/TRG0 UCK Serial Clock 12 P03/INT03/AN03/UO/PPG0 U
Inhaltszusammenfassung zur Seite Nr. 7
Induction Heater C Library User Manual Version 1.2 3.4. IGBT Features MCU-AN-500087-E-12 7 / 18
Inhaltszusammenfassung zur Seite Nr. 8
Induction Heater C Library User Manual Version 1.2 4. System Hardware 4.1. System Connect Diagram The whole system includes pad, fan, main board and front board. They are connected as below. Figure-2 System Connect Diagram Connect Order: Pad to main board; Pad temp to main board; Fan to main board; Front board to main board; MCU-AN-500087-E-12 8 / 18
Inhaltszusammenfassung zur Seite Nr. 9
Induction Heater C Library User Manual Version 1.2 4.2. Front Board Figure-3 is the front board image. It is made up of eight led, a 4-bit digital led and eight buttons. 2 1 3 4 Figure-3 Front Board 1. Connector, connect to main board. 2. Eight led, to display some status. 3. 4-bit digital led, to display power and time. 4. Eight buttons, to control the system. MCU-AN-500087-E-12 9 / 18
Inhaltszusammenfassung zur Seite Nr. 10
Induction Heater C Library User Manual Version 1.2 4.3. Main Board Figure-4 is the main board image. It is made up of power module, mcu control module and IGBT driver module. 1 2 Power 3 IGBT Driver 4 5 Mcu Control 7 6 8 9 10 Figure-4 Main Board 1. 220VAC, to supply power. 2. Pad Connector, to connect the pad. 3. Buzzer, to note some status. 4. Pad temp connector, to test the pad temperature. 5. IGBT power, to supply power to the IGBT. 6. IGBT, is the IGBT chip. 7. MCU, t
Inhaltszusammenfassung zur Seite Nr. 11
Induction Heater C Library User Manual Version 1.2 5. Module Description 5.1. Power Module The 220V is connected by “ICN1 ” and “ICN2 ”. The 220V is rectified by “U4 ”, and supplied to the pad. The “U11 ” is a 15V power module. It supply power to the MCU and IGBT driver. 5.2. IGBT Driver Module The “START ” is the system enable signal. When it is high, the system is enabled, else disabled. The “PPG-IGBT ” is the IGBT drive signal. When it is high, the IGBT is opened, else closed.
Inhaltszusammenfassung zur Seite Nr. 12
Induction Heater C Library User Manual Version 1.2 5.3. Pad Driver Module When the IGBT (U9) is opened, the current flow over the “PAD ”. The “PAD ” is a coil, so it will save the power. The current direction is from left to right. Once the IGBT is closed, because the “PAD ” is a coil, the current direction is still from left to right. Because there is a C11, so it and the “PAD ” are made an oscillation loop, and the power will be saved in the C11. When the system is working, if there i
Inhaltszusammenfassung zur Seite Nr. 13
Induction Heater C Library User Manual Version 1.2 6. System Operate 6.1. Key & Led Definition The system key buttons and leds are defined as below. Error Timer CaoCai HuoGuo DunCai BaoTang BaoWen Power Clear Timer View Power Inc Dec M-Inc M-Dec Key Define Clear---------------Clear the timer. Timer---------------Set the timer. Inc-------------------Power increase. Dec-----------------Power decrease. M-Inc---------------Mode increase. M-Dec--------------Mode decrease. View-----
Inhaltszusammenfassung zur Seite Nr. 14
Induction Heater C Library User Manual Version 1.2 6.2. Operate Descript Turn On/Off When we have connect the power, the “Power ” led will light. We can push the “Power” button to turn on the device, and the “Power ” led will start wink. At anything, we can push the “Power ” button to turn off the device. Mode Change When we turn on the device, the system is in standby. We must push the “M-Inc ” or “M-Dec ” to start the system. The system has six work modes. You can push the “M-I
Inhaltszusammenfassung zur Seite Nr. 15
Induction Heater C Library User Manual Version 1.2 7. Debug and Programming 7.1. Debug Environment and Tools Name Description Manufacturer Notes Windows XP Pro PC OS Microsoft SP2 Softune V3 Software Developing IDE Fujitsu For FFMC-8L MB95F434K Emulator MCU Emulator Fujitsu --- 7.2. Hardware Setup The base hardware connect as below: 7.3. MCU Programming We can programme the MCU by the simulator. The base hardware connect as “6.2 Hardware Setup ”. MCU-AN-500087-E-12 15 /
Inhaltszusammenfassung zur Seite Nr. 16
Induction Heater C Library User Manual Version 1.2 8. Appendix 8.1. Front Board SCH and BOM-List Front Board SCH Front Board BOM-List MCU-AN-500087-E-12 16 / 18
Inhaltszusammenfassung zur Seite Nr. 17
Induction Heater C Library User Manual Version 1.2 8.2. Main Board SCH and BOM-List Main Board SCH Main Board BOM-List Main Board Part List Index Reference Value Footprint Quantity Description 1 B1 BM-330H BGM-330H 1 2 C1 C2 C3 C4 C5 C13 C21 C23 C28 104Z C0805 9 3 C6 C12 C22 C24 100uF/25V CAP100V25 4 4 C7 C9 30P C0805 2 5 C11 0.33uF/1200V HVCAPD27 1 6 C14 5uF/275V HVCAP5U 1 7 C15 2uF/275V HVCAP2U 1 8 C16 C17 681 C0805 2 9 C18 103 C0805 1 10 C19 C26 10uF/2
Inhaltszusammenfassung zur Seite Nr. 18
Induction Heater C Library User Manual Version 1.2 23 ICN1 ICN2 ICN3 ICN4 PCN4 PCN4 4 24 J1 CON10_1 CON10_1 1 25 L1 4.7uH R_6_2_10 1 26 L2 400uH L-400-90 1 27 Q1 Q4 Q6 8050 SOT-23-8050 3 28 Q2 D667 TO-92-D667 1 29 Q5 Q7 8050 TO-92-8050 2 30 R1 3.3R/1W R_11_4_16 1 31 R2 R3 330R R0805 2 32 R4 R5 5.1k R0805 2 33 R6 R9 0R R0805 2 34 R7 330k/2W R_15_5_22 1 35 R8 5.1k R_V 1 36 R10 R11 R15 470k/2W R_15_5_22 3 37 R12 R13 R38 R40 R42 10k R0805 5 38 R14 R17 10
