Inhaltszusammenfassung zur Seite Nr. 1
THE VERMONT
P4000
OWNER’S MANUAL
• WARNING: If your appliance is not properly installed a house fire may result. For your safety,
follow the installation directions. Contact local building or fire officials about restrictions and
installation inspection requirements in your area.
• PLEASE read this entire manual before installation and use of this pellet fuel-burning room heater.
Failure to follow these instructions could result in property damage, bodil
Inhaltszusammenfassung zur Seite Nr. 2
2 INTRODUCTION Thank you for purchasing the Breckwell Pellet Burning Stove, you are now prepared to burn wood in the most efficient, convenient way possible. To achieve the safest, most efficient and most enjoyable performance from your stove, you must do three things: 1) Install it properly; 2) Operate it correctly; and 3) Maintain it regularly. The purpose of this manual is to help you do all three. PLEASE read this entire manual before installation and use of this pellet fuel-burning
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY PRECAUTIONS 3 Do not operate your stove if you smell smoke Never try to repair or replace any part of the coming from it. Turn it off, monitor it, and call your stove unless instructions are given in this dealer. manual. All other work should be done by a trained technician. Never use gasoline, gasoline-type lantern fuel, Do not throw this manual away. This manual kerosene, charcoal lighter fluid, or similar liquids to has important operating and maintenance start or “freshen
Inhaltszusammenfassung zur Seite Nr. 4
4 TABLE OF CONTENTS INTRODUCTION -------------------------------------------------------------------------------------------------- 2 SAFETY PRECAUTIONS --------------------------------------------------------------------------------------- 3 SPECIFICATIONS ------------------------------------------------------------------------------------------------- 5 INSTALLATION -------------------------------------------------------------------------------------------------- 5 Preparation ---------
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION 5 SPECIFICATIONS Width: 25 ¼” Height: 29 ½” Depth: 24 ¼” Weight: 340 lbs. Flue size: 3” or 4” Hopper Capacity: Up to 40 lbs. (this can vary widely depending on pellet size, length, and diameter) EPA status: exempt Burn time: 1 lb. to 4 ½ lbs. per hour BTU range: 8,200 to 40,000 Approved installations: mobile home, alcove, conventional FIGURE 1 PREPARATION Factory packaging must be removed, and some minor assembly work is required prior to install
Inhaltszusammenfassung zur Seite Nr. 6
6 INSTALLATION COMBUSTION AIR SUPPLY For a mobile home installation the stove must be connected to an outside source of combustion air. A 2” inside diameter metallic pipe, either flexible or rigid, may be attached to the inlet at the stove’s rear (refer to figure 4). A rodent guard (minimum ¼” wire mesh)/wind hood must be used at the terminus (refer to figure 5). All connections must be secured and airtight by either using the appropriately sized hose clamp and/or UL-181-AP foil tape. F
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION 7 Equivalent Vent Length (EVL) The longer the run of pipe in your installation (both with inserts and freestandings), the more restriction there is in the system. Therefore, larger diameter pipe should be used. • Use 4” pipe if you have more than 15 feet of equivalent vent length. • Horizontal runs shall not exceed 10 feet of EVL. • It is recommended that vertical runs be a minimum of 8 feet. • To calculate EVL, use the following conversions: 90º elbow or “T” = 5 equiva
Inhaltszusammenfassung zur Seite Nr. 8
8 INSTALLATION B. VERTICALLY WITH NEW CHIMNEY SYSTEM (Refer to Figure 7) NOTE: See “VENTING” and follow L-Vent chimney manufacturer’s instructions. OPTION: To achieve a center vertical installation a 45º elbow and a clean-out tee can be used to offset the pipe from the exhaust outlet to the rear center of the stove. OPTION: Install L-Vent elbow in place of clean-out tee. Locate stove. Drop plumb bob to center of tee outlet, mark point on ceiling. Install ceiling support and L-Ve
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLATION 9 D. VERTICALLY INTO EXISTING MASONRY FIREPLACE NOTE: See “VENTING” and follow L-Vent chimney manufacturer’s instructions. 1. Have the masonry chimney inspected by a qualified chimney sweep or installer to determine its structural condition. 2. You will need a pipe length equal to the chimney height from the hearth. If outside combustion air is to be used, you will need a pipe length equal to the chimney height plus 18 inches. 3. Install a blanking plate and the
Inhaltszusammenfassung zur Seite Nr. 10
10 INSTALLATION ELECTRICAL INSTALLATION This stove is provided with a 6-foot grounded electrical cord extending from the rear of the stove. We recommend connecting to a good quality surge protector that is plugged into a standard three-prong, 120V, 60hz electrical outlet. Voltage variations can lead to serious performance problems. The Breckwell electrical system is designed for 120V AC with no more than 5% variation. Breckwell cannot accept responsibility for poor performance or
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION 11 PANEL CONTROLS (See Figure 12) The blowers and automatic fuel supply are controlled from a panel on the left-hand side of the P4000. The control panel functions are as follows. a. ON/OFF SWITCH • When pushed the stove will automatically ignite. No other firestarter is necessary. The igniter will stay on for at least 10 and up to 15 minutes, depending on when Proof of Fire is reached. The fire should start in about 5 minutes. • The green light located above the On
Inhaltszusammenfassung zur Seite Nr. 12
12 OPERATION PROPER FUEL THIS STOVE IS APPROVED FOR BURNING PELLETIZED WOOD FUEL ONLY! Factory-approved pellets are those ¼” or 5/16” in diameter and not over 1” long. Longer or thicker pellets sometimes bridge the auger flights, which prevents proper pellet feed. Burning wood in forms other than pellets is not permitted. It will violate the building codes for which the stove has been approved and will void all warranties. The design incorporates automatic feed of the pellet fuel into the
Inhaltszusammenfassung zur Seite Nr. 13
OPERATION 13 RE-STARTING A WARM STOVE If the stove has been shut off, and you want to re-start it while it is still warm, the “on/off” button must be held down for 2 seconds. IF STOVE RUNS OUT OF PELLETS The fire goes out and the auger motor and blowers will run until the stove cools. This will take 30 to 45 minutes. After the stove components stop running the “Power” and the BAR GRAPH lights stay on for 10 minutes. After the 10 minutes the “3” light on the bar graph will flash and
Inhaltszusammenfassung zur Seite Nr. 14
14 THERMOSTAT INSTALLATION OPTIONAL THERMOSTAT A thermostat may help you maintain a constant house temperature automatically. A millivolt thermostat is required. A fixed wall mount or Breckwell’s hand held model can be used. The control panel can be set up two ways to operate your stove in thermostat mode. NOTE: YOUR THERMOSTAT SHOULD BE INSTALLED BY AN AUTHORIZED DEALER OR SERVICE PERSON. THERMOSTAT INSTALLATION • A MILLIVOLT THERMOSTAT IS REQUIRED. • Unplug sto
Inhaltszusammenfassung zur Seite Nr. 15
OPERATION 15 OPERATING SAFETY PRECAUTIONS PLEASE READ THIS! a. Hot while in operation. Keep children, clothing, and furniture away. Contact may cause skin burns. b. If you notice a smoldering fire (burnpot full but no visible flame) AND a heavy smoke buildup in firebox, immediately TURN OFF the stove, but DO NOT unplug it. Do not open the door, change the damper setting or tamper with any controls on the stove. Wait until firebox clears, and blowers shut down, do as instructed in “PR
Inhaltszusammenfassung zur Seite Nr. 16
16 MAINTENANCE FAILURE TO CLEAN AND MAINTAIN THIS UNIT AS INDICATED CAN RESULT IN POOR PERFORMANCE AND SAFETY HAZARDS. NEVER CLEAN WHEN HOT. NOTE: Inspect burn pot periodically to see that holes have not become plugged, if so, clean thoroughly. ASH REMOVAL Ashes should be placed in a metal container with a tight-fitting lid. The closed container or ashes should be placed on a noncombustible surface or on the ground, well away from all combustible materials pending final disposal.
Inhaltszusammenfassung zur Seite Nr. 17
MAINTENANCE 17 CLEANING Baffle Plates a. Heat Exchange Tubes – Your Breckwell stove is designed with a built-in heat exchange tube cleaner. This should be used every two or three days to remove accumulated ash on the tubes, which reduces heat transfer on the P4000. Insert the handle end (with hole) of the cleaning tool onto the cleaning Air Switch Tube rod (refer to figure 15). The cleaner rod is located in the grill above the stove door. Move the cleaner rod back and forth
Inhaltszusammenfassung zur Seite Nr. 18
18 MAINTENANCE CHIMNEY CLEANING a. Creosote Formation – When any wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue or a newly started fire or from a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire, which may damage the chimney or even destroy the house. Despite their
Inhaltszusammenfassung zur Seite Nr. 19
TROUBLESHOOTING GUIDE 19 When your stove acts out of the ordinary, the first reaction is to call for help. This guide may save time and money by enabling you to solve simple problems yourself. Problems can be caused by to only five factors: 1) poor fuel; 2) poor operation or maintenance; 3) poor installation; 4) component failure; 5) factory defect. You can usually solve those problems related to 1 and 2. Your dealer can solve problems relating to 3, 4 and 5. Refer to figures 20, 21 and 22
Inhaltszusammenfassung zur Seite Nr. 20
20 TROUBLESHOOTING GUIDE STOVE SHUTS OFF AND THE # 3 LIGHT FLASHES Possible Causes: Possible Remedies: (Unplug stove first when possible) 1. The hopper is out of pellets. Refill the hopper. 2. The air damper is too far open for a low feed setting. If burning on the low setting, you may need to close the damper all the way (push the knob in so it touches the side of the stove). 3. The burnpot is not pushed completely to the rear of the firebox. Make sure that the air in
