Inhaltszusammenfassung zur Seite Nr. 1
12” HOT/COLD LAMINATOR
Model 92500
OpeRATINg INsTR uCTIONs
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS manual.
© ®
Copyright 2
Inhaltszusammenfassung zur Seite Nr. 2
pRODuCT speCIFICATIONs Electrical Requirements 110 V~, 60 Hz, 2 A Indicators Red LED - Power Green LED - Ready External Fuse 3.15A250V Glass Tube Motor Synchronous Power Plug 3 Prong, Grounded Maximum Laminating Width 12” Maximum Document Thickness .6mm (.024”) Maximum Film Thickness 0.0030”-0.0040” Laminating Speed Approx. 12” Per Minute Heat Dial Increments 1 To 10 Warm Up Time 5 to 10 Minutes Maximum Temperature 350° Fahrenheit Overall Dimensions 18” L x 8-1/4” W x 4” H Weight 8.4 Pounds uNpA
Inhaltszusammenfassung zur Seite Nr. 3
2. Do not operate the Laminator in explosive atmospheres, such as in the pres- ence of flammable liquids, gases, or dust. Electrical equipment creates sparks which may ignite flammables. 3. Keep bystanders, children, and visitors away while operating laminating equipment. Distractions can cause you to lose control. Protect others in the work area from accidents. peRsONAL sAFeTY 1. stay alert. Watch what you are doing, and use common sense when operating a Laminator. Do not use laminati
Inhaltszusammenfassung zur Seite Nr. 4
6. Maintain laminating equipment with care. Do not use damaged equipment. Tag damaged equipment “Do not use” until repaired. 7. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect operation of the Laminator. If damaged, have the equipment serviced before using. Many accidents are caused by poorly maintained equipment. 8. use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitabl
Inhaltszusammenfassung zur Seite Nr. 5
speCIFIC sAFeTY R uLes 1. Maintain labels and nameplates on the Laminator. These carry important infor- mation. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Always place the Laminator on a dry, flat, level, sturdy non-flammable work surface capable of supporting the weight of the Laminator and any additional accessories. Make sure to place the Laminator in a location that is out of reach of children. 3. Never place objects on top of the Laminator. Always ch
Inhaltszusammenfassung zur Seite Nr. 6
gROuNDINg WARNINg! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facil- ity before use. If the plug will not fit the outlet, have a proper outlet
Inhaltszusammenfassung zur Seite Nr. 7
exTeNsION CORDs 1. Grounded tools require a three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a seri- ous drop in voltage, resulting in loss of power and possible tool damage. (see Table A.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (see Tabl
Inhaltszusammenfassung zur Seite Nr. 8
sYMBOLOgY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current V~ Amperes A No Load Revolutions per Minute (RPM) n xxxx/min. 0 SKU 92500 For technical questions, please call 1-800-444-3353 PAGE 8
Inhaltszusammenfassung zur Seite Nr. 9
OpeRATINg INsTR uCTIONs Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 11. ReD LeD LIgHT (3) HOT / COLD sWITCH (9) pOWeR sWITCH (1) TeMpeRATuRe ADJusTMeNT KNOB (5) gReeN LeD LIgHT (4) ADJusTABLe FRONT guIDe pLATFORM FIguRe D (6) 1. Plug the Power Cord (2) into the nearest 110 volt, grounded, electrical outlet. (see Figure D.) 2. Turn the Power Switch (1) on the side of the unit to its “ON” position. NOTE: The Red LED
Inhaltszusammenfassung zur Seite Nr. 10
7. Make sure the sealed edge of the laminating film is inserted first into the Lamina- tor to avoid jamming. Keep hands and fingers clear of the Adjustable Front guide (6). 8. Once inserted into the Laminator, the laminating object will be automatically drawn into the Laminator and ejected from the Rear Guide Platform (7). To avoid pos- sible accidental burns, make sure to wear safety gloves (not included) when first removing the laminating object from the Rear guide platform. (see Assy. D
Inhaltszusammenfassung zur Seite Nr. 11
pLeAse ReAD THe FOLLOWINg CAReFuLLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEM
