Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTIONS FOR OPERATION AND CARE
XVGA GRATER/SHREDDER AND
XVSA SLICER ATTACHMENTS
Our versatile grater/shredder attachments can be used to grate and shred cheeses, raw vegetables, nuts, breadcrumbs, etc.
depending on the plate selected. Our S/S plates are available with 3/32", 3/16", 1/4", 5/16" or 1/2" size holes and a special
grating plate for breadcrumbs & hard cheeses. A plate holder with shaft and one 3/16" plate are included with the XVGA
attachment.
Our slicer attachments can be used f
Inhaltszusammenfassung zur Seite Nr. 2
TO INSTALL SHREDDER OR GRATER DISCS Stop the machine. Orient the plate with the cutting edge away from the shaft assembly. Locate the keyhole slots on the plate and slide the wide part of the slots over the studs on the plate holder. When the plate is flush with the holder, rotate it clock- wise to lock it in position. It is possible to loosely assemble the plate to the hub (sharp edge out), then place it on a work sur- face (the teeth on the plate will mar a finished table). Press down and turn
Inhaltszusammenfassung zur Seite Nr. 3
Locking Pin TO REMOVE XASP ADJUSTABLE SLICE PLATE ASSEMBLY FROM HOUSING Open the door all the way and raise the locking pin XP1007 (on top of rear of housing) and the assembly will be free for removal by pulling outward. Open Door Thumb Screw TO REMOVE ATTACHMENT FROM POWER UNIT Loosen thumbscrew on power unit until hub is free for removal from unit. PUSHER PLATE REMOVAL Raise the Pusher Plate and slide it out of the slot in the door XVSD. OPERATION Thumb Screw 1. Stop the power unit (mixer,
Inhaltszusammenfassung zur Seite Nr. 4
4. Drop the hinge pins of the front door into the holes in the housing. Pusher Plate 5. Close the slicer front door and fasten the latch. 6. Start the machine. Set at a speed to produce the best product (see machine manual) 7. Raise the pusher plate lever. Pusher Plate 8. Place the food to be sliced in the hopper and gently press Lever down on the pusher plate lever. Note: Too much pressure crushes the food and causes CAUTION: Keep Hands out of Hopper – use a irregularity in the slices. Large
Inhaltszusammenfassung zur Seite Nr. 5
Adjustment 6.When using the adjustable slicer plate, make sure it is Thrust Nut cleaned frequently to assure easy thickness adjustment. Bearing Occasionally disassemble the slicer plate for a thorough cleaning. To do this it is necessary to unscrew the knurled thrust bearing, which has a left hand thread, to Spring release the spring. Withdraw the knife and shaft assem- bly. Unscrew the adjusting nut from the plate. Use a drop of approved food machinery oil on the shaft and adjust- ment threads
Inhaltszusammenfassung zur Seite Nr. 6
PART NUMBER LISTING XVSH HOUSING XVSH Housing size 12 XP1004 Threaded (Hex) Pin for housing latch XP1005 Latch with setscrew XP1005A Latch setscrew only XP1007 Shaft Lock knob - top XP1008 Housing Hub with locating pin – six holes XP1009 Flat Head Machine Screw (6) for hub XP1010 Knife Lock Screw XP1011 Fiber gasket XPH PLATE HOLDER XPH Plate Holder Assembly Complete XP1026 Brass Collar with set screw XP1026A Set Screw for Collar XP1030 Stud for Plate Holders XSP332 3/32" S/S Shredder Plate XS
Inhaltszusammenfassung zur Seite Nr. 7
Shredder and Grater Plate Hole Sizes with Typical Applications 1/2" 5/16" 3/16" 3/32" Universal Food Shredder Shredder Shredder Shredder Grater Product Plate Plate Plate Plate Plate 000 0 3 7 14 Cole Slaw Bread Crumbs Cheese Soft Cheese For Pizza Carrots For Coloring Cheese For Tacos Hard Cheese Stainless steel Shredder Plate hole sizes (not drawn to scale) SS Grater Plate For Hard 3/32" 3/16" 5/16" 1/4" 1/2" Cheese only 7
Inhaltszusammenfassung zur Seite Nr. 8
LIMITED XVSA/XVGA ATTACHMENT WARRANTY Globe Food Equipment Company (“GFE”) warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions within North America and subjected to normal use, is free from defects in material or workmanship for a period of 1 year from invoice date. The XVSA Vegetable Slicing Attachment and XVGA Shredder/Grater Attachment have a 1-year replacement warranty. There is no labor warranty for mixer attachment
