Inhaltszusammenfassung zur Seite Nr. 1
Owner’s Manual
PUV-Basic
PUV-8
PUV-16
(NSF Standard 55
Class B Certified)
Congratulations. By purchasing this system, you have taken the first step in ensuring
safe drinking water. Designed using the most advanced UV technology available
today, your UV system is designed to provide you with years of trouble free
operation with minimal maintenance required.
KEY INFORMATION YOU SHOULD KNOW:
• A 5-micron (nominal) sediment filter must
Inhaltszusammenfassung zur Seite Nr. 2
Potential Safety Measures Hazard UV Exposure Never illuminate UV Lamp outside of the UV Chamber. Never look directly at illuminated UV Lamp, even when using protective gear. Always use protective gear, including gloves and UV safety glasses. If accidental exposure occurs, immediately cool affected area and consult physician. Electrical Shock Disconnect power to system before performing any maintenance or repair. There may be more than one source of power. Impalement Never perform any physical
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INSTRUCTIONS GROUNDING This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock. This system is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER – Improper connection of the equipment-gro
Inhaltszusammenfassung zur Seite Nr. 4
TABLE OF CONTENTS Overview 3 What model do I have? 3 Specifications 4 Components 5 Dimensions and layout 7 Installation 9 Installing the UV system 9 Disinfecting the water lines 11 Operation 14 Control panel 14 Troubleshooting 15 Maintenance 16 Sleeve cleaning and lamp replacement 17 Warranty 20 2 OVERVIEW WARRANTY MAINTENANCE OPERATION INSTALLATION
Inhaltszusammenfassung zur Seite Nr. 5
OVERVIEW INSTALLATION OPERATION MAINTENANCE WARRANTY 6 5 4 2 1 3 HISTORY: NOTE: DATE REV SHT ZONE REVISION DESCRIPTION LOG NO. REV BY CHK BY APPD BY YYYY-MM-DD 1. LABEL TO BE PRINTED ON 602919 LABEL STOCK. A DRAWING RELEASED 07-979 CL DGP DGP 2008-01-18 2. SEE SHEET 2 DESIGN TABLE FOR "A", "B", "C" AND "SYSTEM DESCRIPTION". 3. SERIAL NUMBER "000001" IS AN EXAMPLE OF THE FIRST SERIAL NUMBER OF THIS TYPE OF SYSTEM. THE D NUMBER WILL INCREASE FOR EACH ADDITIONAL SYSTEM PRODUCED. LABEL VISION WI
Inhaltszusammenfassung zur Seite Nr. 6
SPECIFICATIONS General (All Models) Operating Parameters Maximum operating pressure 125 PSI (862 kPa) Minimum operating pressure 4 PSI (27.5 kPa) 0 0 Maximum ambient air temperature 122 F (50 C) 0 0 Minimum ambient air temperature 32 F (0 C) Maximum humidity 100% Maximum hardness 120 ppm (7 grains per gallon) Maximum iron 0.3 ppm Minimum UVT 70% Installation Vertical or horizontal* Flow Restrictor Yes NSF Standard 55 NSF Certification Class B Rated service life of lamp 1 ye
Inhaltszusammenfassung zur Seite Nr. 7
OVERVIEW INSTALLATION OPERATION MAINTENANCE WARRANTY COMPONENTS For replacement components please contact your installer or contact VIQUA directly for a referral: 1 800 265 7246 (North America), 519 763 1032, or info@viqua.com. Components - PUV -Basic, PUV-8, PUV-16 Part 1 Part Number Power supply mounting All -- 1 bracket Reference card All 603069 2 Power supply PUV-Basic 650713-006 3 2 (includes Power supply PUV-8, 650713-007 mounting bracket, PUV-16 Reference card, Safety cap, Lam
Inhaltszusammenfassung zur Seite Nr. 8
Components - All Models Part Model Part Number Lamp PUV-Basic, 602805 7 (includes O-rings) PUV-8 PUV-16 602806 O-ring All -- 8 7 Sleeve bolt All 602665 9 Sleeve PUV-Basic 602732 10 (includes O-rings) PUV-8 PUV-16 602733 UV Chamber All -- 11 (includes Chamber clamp(s), and Ring clamp*). Ring clamp All -- 12 8 Chamber clamp(s) All -- 13 9 Solenoid valve kit PUV-8 650717-001 14 (optional) (3/4") 8 (includes Junction Box) PUV-16 650717-002 CoolTouch val
Inhaltszusammenfassung zur Seite Nr. 9
OVERVIEW INSTALLATION OPERATION MAINTENANCE WARRANTY DIMENSIONS AND LAYOUT OUTLET Clearance for lamp removal A B D L 13 ( ) 48” 122cm 14 C 9 8 10 12 11 To Drain L 16 7 Ø 3 4 INLET 1 2 5 6 Model L Ø A B C D (max.) (max.) PUV-Basic 20.5" 4" 72" 8.5" 6" 54" (52cm) (10cm) (183cm) (22cm) (15cm) (137cm) PUV-8 20.5" 4" 72" 8.5" 6" 54" (52 cm) (10cm) (183cm) (22cm) (15cm) (137cm) PUV-16 30" 4" 72" 8.5" 6" 54" (76cm) (10cm) (183cm) (22cm) (15cm) (137cm) 7 WARRANTY
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION MAINTE- NANCE WARRANTY 1 Sample valve: Allows for sampling of raw water. 2 Shut-off valve: Required to allow maintenance of pre-treatment equipment. Pre-treatment (illustrative only): For the UV system to operate effectively, the water should meet certain 3 water quality parameters, as outlined below. To meet these, pre-treatment of the water may be required. Pre- treatment equipment must be installed BEFORE the UV chamber. Pre-treatment systems can be comprised of one or more of the
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION OVERVIEW OPERATION MAINTENANCE WARRANTY INSTALLING THE UV SYSTEM 1 6 Determine appropriate indoor location of Slide power the power supply and chamber, referring supply onto to Dimensions and Layout drawing. mounting Power supply should be installed higher bracket. than chamber away from all water sources. Ensure adequate clearance above chamber to allow for removal of the lamp and sleeve. 2 7 Screw chamber clamp(s) to the wall (#10 Slide screws recommended.) Reference car
Inhaltszusammenfassung zur Seite Nr. 12
11 14 Attach ground (green/yellow) and strain Outlet must be relief (red) wires from the lamp plug to protected by a the ground lug on the chamber. Secure Ground Fault both wires with locking screw provided. Circuit Interrupter (GFCI). 15 Let water flow to one faucet or other water outlet, then close the outlet and check for leaks. Proceed to Disinfecting The Water Lines. Locking Ground and screw strain relief Ground wires lug 12 Push safety cap into place. 13 Flow direction must
Inhaltszusammenfassung zur Seite Nr. 13
INSTALLATION OVERVIEW OPERATION MAINTENANCE WARRANTY DISINFECTING THE WATER LINES UV systems disinfect the water using ultraviolet light, treating the water as it passes through the system. When there is a risk that water downstream of the UV system has been contaminated, it is critical that these water lines be chemically disinfected. Disinfection of the water lines is therefore required after initial system installation and following any period of time during which the system is inoperativ
Inhaltszusammenfassung zur Seite Nr. 14
8 11 Allow water to fill Let the bleach sit in the water lines for at UV chamber. least four hours. 9 12 13 10 Go to a water outlet and allow the cold water to flow until you can smell bleach, then stop the flow. Allow hot water (if present) to flow until you can smell bleach, then stop the flow. Repeat procedure at all water outlets. Remember to include all faucets, washing machines, toilets, outside taps, and other water outlets. Note: You will likely run out of bleach; if you cannot
Inhaltszusammenfassung zur Seite Nr. 15
INSTALLATION OVERVIEW OPERATION MAINTENANCE WARRANTY 16 20 17 21 Flush all water outlets until bleach can no longer be smelled (at least 5 minutes). 18 19 13
Inhaltszusammenfassung zur Seite Nr. 16
CONTROL PANEL A B C 1 2 3 Buttons and Display For all models. Lamp timer Counts down from 365 days to show time for annual lamp replacement. A display Lamp timer After installing a new lamp, press and hold for five seconds to reset Lamp timer to B reset 365. Mute Press to silence audible alarm. C When the alarm is due to the lamp's age, the mute button will silence the audible alarm for 7 days; this may be repeated up to a maximum of 4 times. After that, the button will silence for only 24
Inhaltszusammenfassung zur Seite Nr. 17
OPERATION OVERVIEW INSTALLATION MAINTENANCE WARRANTY TROUBLESHOOTING The table below is a list of possible causes and solutions. Before replacing parts, please contact VIQUA Technical Assistance for any new troubleshooting techniques : 1-800-265-7246 Symptom Possible cause Possible solution No power GFCI and/or breaker tripped Reset GFCI and/or breaker Transient voltage surge suppressor (TVSS) Replace TVSS damaged Power supply damaged Replace power supply and use a TVSS GFCI or breaker Connec
Inhaltszusammenfassung zur Seite Nr. 18
SLEEVE CLEANING & LAMP REPLACEMENT Sleeve cleaning Minerals in the water slowly form a coating on the sleeve. This coating must be removed because it reduces the amount of UV light reaching the water, thereby reducing purification performance. Basic models: please clean the sleeve regularly (3-4 times per year, or more often depending on water quality). When only cleaning is required, follow instructions and re-install the current lamp. Lamp replacement The amount of UV light created by the l
Inhaltszusammenfassung zur Seite Nr. 19
MAINTENANCE OPERATION WARRANTY OVERVIEW INSTALLATION 1 6 2 1 Squeeze tabs 2 7 Open a tap downstream of the UV unit to Strain relief release pressure. Then, close this tap. wires should remain connected. 3 8 Hold by 2 sleeve bolt to remove lamp/sleeve assembly. 1 4 9 For sleeve cleaning only: 5 Let the system cool for 10 minutes. Skip to step 14. Note: Sleeve must be replaced if it cannot be completely cleaned or if it appears scratched or cracked. For lamp or sleeve replacement: Clean
Inhaltszusammenfassung zur Seite Nr. 20
10 13 Screw lamp into sleeve hand-tight. Caution: Over tightening will break the sleeve. 2 1 2 Lamp tab 1 Sleeve bolt 11 14 Make sure lamp/sleeve assembly is centered. 1 Caution: Over tightening 2 will break the sleeve. Remove o-rings and sleeve bolt from sleeve. 12 15 Align connections by rotating ring clamp (if equipped) to push lamp plug onto end of lamp. Reinstall sleeve bolt ring with 2 new o-rings. clamp 18 MAINTENANCE WARRANTY OPERATION INSTALLATION OVERVIEW
