Inhaltszusammenfassung zur Seite Nr. 1
FT94
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW TREADMILL!
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Product Registration ...2 Important Safety Instructions 3 Important Electrical Information .4 Important Operation Instructions 5 Assembly instructions ..6 Folding Instructions .11 Operation of Your New Treadmill .12 Programmable Features .16 General Maintenance. 17 Service Checklist - Diagnosis Guide .20 Manufacturer s Limited Warranty ... 21 FT94 -1-
Inhaltszusammenfassung zur Seite Nr. 3
CONGRATULATIONS ON YOUR NEW TREADMILL AND WELCOME TO THE SOLE FAMILY! Thank you for your purchase of this quality treadmill from FUEL. Your new treadmill has been manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. FUEL will do all we can to make your ownership experience as pleasant as possible for many years to come. If you have a problem that requires service, call FUEL at: 866-545-3835,or send an email to:
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions WARNING - Read all instructions before using this appliance. DANGER - To reduce the risk of electric shock disconnect your FUEL treadmill from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the treadmill on a flat level surface with access to a 120-volt, 15-amp grounded outlet with only the treadmill plugged into the circuit.. DO NOT USE AN EXTENSION CORD UNLESS
Inhaltszusammenfassung zur Seite Nr. 5
Important Electrical Information WARNING! NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Large switching currents of the drive motor will trip GFCI type outlets, as with any appliance with a large motor. Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels. NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%) or more, the performance of your treadmi
Inhaltszusammenfassung zur Seite Nr. 6
Important Operation Instructions NEVER operate this treadmill without reading and completely understanding the results of any operational change you request from the computer. Understand that changes in speed and incline do not occur immediately. Set your desired speed on the computer console and release the adjustment key. The computer will obey the command gradually. NEVER use your treadmill during an electrical storm. Surges may occur in your household power supply that could damage treadm
Inhaltszusammenfassung zur Seite Nr. 7
Assembly Instructions (FT94) !!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ BEFORE UNPACKING YOUR FOLDING TREADMILL!! Serious injury could occur if this folding treadmill is not unpacked properly. There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding accidentally during shipping. If this strap is not removed properly the treadmill could spring open unexpectedly and cause injury if someone is standing near the treadmill when the strap i
Inhaltszusammenfassung zur Seite Nr. 8
ASSEMBLY PACK CHECK LIST #95. 5/16 x19x1.5T #96. M5 x 10 m/m Curved Washer (8pcs) Phillips Head Screw (6pcs) #90. 3.5x12 m/m #94. 5/16 x15m/m Self Tapping Screw (4pcs) Button Head Socket Bolt (14pcs) #93.Lubricant (1pc) #102. Safety Key (1pc) #97. Combination M5 Allen #98. M6 Allen Wrench (1pc) Wrench & Phillips Head Screw Driver(1 pc) FT94 -7-
Inhaltszusammenfassung zur Seite Nr. 9
Step 1. Remove the treadmill from the carton and lay it aside on a smooth level surface. Step 2. Connect the Lower Computer Cable (38) with the Middle Computer Cable (37). 37 38 Step 3. Insert the Upright tubes (4,5) into the Frame Base with the eight 5/16 x15mm Button Head Socket Bolts (94) and four 5/16" x 19 x 1.5T Curved Washers (95) - on the bolts for the side of the tubes - using the M5 Allen Wrench (97). Be careful not to pinch the computer cable while installing the right Upright tub
Inhaltszusammenfassung zur Seite Nr. 10
Step 4. Install the Left Handrail Cover (41) onto the Left Upright tube (4), Right Handrail Cover (40) onto the Right Upright tube (5). Make sure they are facing the correct direction and allow them to slide down and sit at the bottom of the tubes. 40 41 4 5 Step 5. Connect the middle Computer Cable (37) with the upper Computer Cable (36). 36 37 Step 6. Install the Console Assembly (39) into the Upright tubes (4,5) with the six 5/16 x15mm Button Head Socket Bolts (94) and four 5/16" x 19 x 1.
Inhaltszusammenfassung zur Seite Nr. 11
Step 7. Install the Left and Right Handrail Covers (41, 40) onto the Console Assembly (39) with the four 3.5x12mm Self Tapping Screws (90). 39 40 41 90 97 90 Step 8 Install the Frame Base Caps (44,43) onto the Frame Base with six M5x10mm Phillips Head Screws (96). 43 96 44 97 96 Please Ensure All Screws are tightened After All Components Assembly Complete. FT94 -10-
Inhaltszusammenfassung zur Seite Nr. 12
Folding Instructions Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired position. UNFOLDING Hold the treadmill running board with your left hand. Pull the locking knob with your right hand and slowly lower the treadmill running board. FOLDING Ensure the incline angle of the treadmill is at its lowest position. Lift the treadmill running board up until lo
Inhaltszusammenfassung zur Seite Nr. 13
W Operation of Your Treadmill Getting familiar with the control panel FT94 Console Initial Display: When the power is turned on, the main display will light up showing all characters. The console will be performing an internal test to make sure the console is operational. The display will then scroll through three numbers, the first showing the current software version, second is how many hours the treadmill has been in use and third is how many virtual miles the treadmill has gone. The treadmil
Inhaltszusammenfassung zur Seite Nr. 14
WINDOW DISPLAY DATA: SCAN: When lit, will scan through all the display information; each one for 5 seconds. SPEED: Displays the current belt speed from starting at 1.0Mph to 10.0Mph. TIME: Accumulates total workout time from 00:00 to 99:59. DISTANCE: Accumulates total workout distance from 0.00 to 99.99 miles. CALORIES: Accumulates the user s calorie consumption during exercise. Max. Value is 9999 calories. PULSE: Displays your current heart rate in beats per minute from 40 to 240. ♥ Icon: The
Inhaltszusammenfassung zur Seite Nr. 15
set the time to count down, see STEP 7. STEP 3: Press the SELECT button to scroll through your workout data. The initial screen will be showing the SPEED. Pressing the SELECT button will show the TIME then DISTANCE, CALORIES, PULSE, INCLINE and SCAN. In scan mode each data will be displayed for 5 seconds. STEP 4: To get a pulse reading, simply grasp both stainless steel pick-ups. Make sure the display is set to show Pulse, or Scan. When the ♥ Icon is flashing that means the console is receiving
Inhaltszusammenfassung zur Seite Nr. 16
To Select a Program: Step 1: Press the ^ or v button to choose P1 ~ P5, each program has a preset speed value. Step 2: Press the ENTER button to set the count down time from 10:00 to 99:00; the preset value is 20:00. You can adjust the value by pressing FAST/SLOW or press START button to start training immediately. Step 3: Press STOP button to stop your workout or pull safety key away from its position to shut down the computer. Pulse Feature: The Pulse (Heart Rate) window will display your curr
Inhaltszusammenfassung zur Seite Nr. 17
Programmable Features Speed Incline P1 P2 P3 P4 P5 FT94 -16-
Inhaltszusammenfassung zur Seite Nr. 18
General Maintenance Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is maximized when the bed is kept as clean as possible. Use a soft, damp cloth or paper towel to wipe the edge of the belt and the area between the belt edge and frame. Also reach as far as practical directly under the belt edge. This should be done once a month to extend belt and bed life. Use water only - no cleaners or abrasives. A mild soap and water solution along with a nylon scrub br
Inhaltszusammenfassung zur Seite Nr. 19
TREADBELT TRACKING ADJUSTMENT: The performance of your treadmill is dependent on the frame running on a reasonably level surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt adjustment may be necessary. The treadmill is designed to keep the treadbelt reasonably centered while in use. It is normal for some belts to drift near one side while the belt is running with no one on it. After a few minutes of use, the treadbelt should have a tendency to cen
Inhaltszusammenfassung zur Seite Nr. 20
Belt/deck lubrication procedure: Do not lubricate with other than FUEL approved lubricant. Your treadmill comes with one tube of lubricant and extra tubes can be ordered directly from FUEL. There are commercially available lube kits, but the only one currently approved by FUEL is Lube-N-Walk. These kits come with an application wand that makes applying the lubrication easier. The kits can be purchased directly from Lube-N-Walk here: http://www.jadfitness.com/. Keeping the deck lubricated at the
