Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTION MANUAL
Air Cleaner
50-868
PART NO. 410-09-651-0004 - 09-23-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
ESPAÑOL: PÁGINA 11
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Inhaltszusammenfassung zur Seite Nr. 2
GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust
Inhaltszusammenfassung zur Seite Nr. 3
13. DO NOT ATTEMPT TO REMOVE OR REPLACE THE FILTER(S) WHILE THE UNIT IS RUNNING.Make certain that the unit is disconnected from the power source. 14. MAINTAIN THE UNIT IN TOP CONDITION. Keep filters clean for optimum performance. Follow all instructions for changing and cleaning filters. 15. STORE THIS UNIT IN A LOCATION that eliminates the potential of damage to the power cord. Safely store power cord on the unit to eliminate tripping hazards. 16. TURN THE UNIT “OFF” AND DISCONNECT IT FROM THE
Inhaltszusammenfassung zur Seite Nr. 4
HOLES GROUNDED OUTLET BOX GROUNDED OUTLET BOX CURRENT GROUNDING CARRYING MEANS PRONGS ADAPTER GROUNDING BLADE IS LONGEST OF THE 3 BLADES HOLES Fig. A Fig. B EXTENSION CORDS MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS Ampere Volts Total Length of Gauge of Rating Cord in Feet Extension Cord 0-6 120 up to 25 18 AWG 0-6 120 25-50 16 AW
Inhaltszusammenfassung zur Seite Nr. 5
CARTON CONTENTS E B D A C Fig. 2 A - Air cleaner B - Four 1” eye-bolts C - Four 1/4-20 flange nuts D - Four rubber feet E - Remote Control Unit (Batteries not included) ASSEMBLY INSTRUCTIONS Determine whether the Air Cleaner will be used on the floor, on a bench, or hanging from an overhead support. If the Air Cleaner will be used as a mobile unit, proceed to “USINGTHE AIRCLEANERONABENCH OR FLOOR SURFACE” section. For overhead or ceiling mounting, refer to section “MOUNTING THE AIR CLEANER TO A
Inhaltszusammenfassung zur Seite Nr. 6
USING THE AIR CLEANER ON A BENCH OR FLOOR SURFACE 1. Locate (4) self-adhesive rubber feet (A)Fig. 3, supplied with the unit. Carefully place Air Cleaner on a firm supporting surface with access to the bottom of the cabinet Apply a self-adhesive rubber foot (A) Fig. 3, to the bottom at each corner of the air cleaner cabinet. The rubber feet will help eliminate vibration and will prevent A the possibility of the air cleaner “walking” across the work or floor surface. For operator safety, clamp the
Inhaltszusammenfassung zur Seite Nr. 7
D 1. Locate the four 1" eye bolts and the four 1/4-20 flange nuts supplied with the unit. C 2. Use a 5/32” Allen wrench (not supplied) to remove the four screws, (C) Fig. 5 from the top of air cleaner (D). 3. Thread one flange nut on the bolt approximately 3/4" of the threaded portion of the bolt. 4. Thread each eye-bolt into each of the four holes where screws were removed in STEP 2. Fig. 5 5. Fig. 6 illustrates the four eye bolts (F) attached to the top of the air cleaner. NOTE: Be certain tha
Inhaltszusammenfassung zur Seite Nr. 8
USING THE REMOTE CONTROL B H F C G D To reduce the risk of fire or electric shock, do not use this unit with any solid-state speed control device. The remote control provided with this A unit is not considered a solid-state device. E The Air Cleaner is equipped with a REMOTE CONTROl I (A) Fig.7A. NOTE: The remote requires two (2) AAA batteries (not supplied). Battery housing is located Fig. 7B Fig. 7A inside the back cover. The 50-868 Dust Collector provides a timer that can be Notice that the r
Inhaltszusammenfassung zur Seite Nr. 9
MAINTENANCE CHANGING AND CLEANING FILTERS 1. To remove the outer first stage filter (A) Fig. 8, lift and pull out the bottom of the filter as shown. 2. Remove inner bag filter (B) Fig. 9 in the same manner. 3. The first stage filter can be replaced or cleaned depending on its condition. Clean this filter in one of two ways: Use a shop vac to remove the dust, or use compressed air (30 psi maximum) to blow the dust out of the filter. Compressed air can be dangerous. For operator safety, do not ex
Inhaltszusammenfassung zur Seite Nr. 10
PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a net- work of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain addi- tional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582). Delta Building Trades and Home Shop
Inhaltszusammenfassung zur Seite Nr. 11
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) ARIZONA ILLINOIS MINNESOTA Cleveland 44125 Minneapolis 55429 Tempe 85282 (Phoenix) Addison 60101 (Chicago) 8001 Sweet Valley Drive 5522 Lakeland Avenue North 2400 West Southern Avenue 400 South Rohlwing Rd. Unit #
