Bedienungsanleitung Star Trac SPINNER BIKE NXT 7000

Inhaltszusammenfassung zur Seite Nr. 1

Spinner® Bike
Installation Instructions



NXT 7000


ELITE 6900 PRO 6800

Inhaltszusammenfassung zur Seite Nr. 2

Page 1 of 9Star Trac Product Support 800-503-1221 Installation Instructions AS SETUP SPIN BIKE ASSEMBLY AND SETUP Use the following procedures to unpack and assemble your STAR TRAC SPINNER ® BIKE. Prepare the area that you will be unpacking and assembling the bike to be free from debris that may cause damage. Observe all safety precautions and care while unpacking and assembling the bike. UNPACKING Open the shipping carton, carefully remove all parts from the shipping carton

Inhaltszusammenfassung zur Seite Nr. 3

Page 2 of 9Star Trac Product Support 800-503-1221 Assembly Following these steps in order will minimize the build time and ensure proper assembly. Note: Not all of the following procedures are performed on all models; Spinner ® Pro, Elite and NXT. If the procedure is particular to that model only it will be noted as follows: (NXT Only) or (Pro/Elite Only) or (NXT/Elite Only) Installation of the Rear Leg Assembly Lift up the rear of the bike frame and place the rear leg assem

Inhaltszusammenfassung zur Seite Nr. 4

Page 3 of 9Star Trac Product Support 800-503-1221 NXT Only 1. Position the leg so the thicker end faces toward the front of the bike 2. Using the 5mm hex wrench and a 13mm combination wrench insert 2- M10X55mm (rear- most holes) and 2-M10X65mm (front-most holes) button head screws, nuts and washers (under bolt head and nut), to secure the rear leg assembly to the frame. The nut should be on the bottom of the bike and the head of the screw on the top of the bike. 3. Tighten all

Inhaltszusammenfassung zur Seite Nr. 5

Page 4 of 9Star Trac Product Support 800-503-1221 Installation of the Saddle and Seat Slider 1. Install the seat post into the frame and lower it to the lowest position and tighten the pop pin securely. 2. Slide the seat slide into the top of the seat post with the saddle pointed towards the front of the bike. NXT Only 1. Rotate the seat slider lock knob as needed so that the slider clamp is in alignment with the guide rail 2. There is a locking pin under the saddle that has to

Inhaltszusammenfassung zur Seite Nr. 6

Page 5 of 9Star Trac Product Support 800-503-1221 Installation of the Handlebar Pop Pin 1) Insert the pop pin into the front of the bike frame. 2) Hand-tighten the nut of the pop pin hand tight taking care not to cross tread it. 3) Using a wrench tighten the pop pin assembly. Assembly and Installation of the Handlebar and Post NXT Only 4) Positioning the handlebar post with the numbers 1 on top and insert the handlebar into the handlebar sleeve locking it at numbe

Inhaltszusammenfassung zur Seite Nr. 7

Page 6 of 9Star Trac Product Support 800-503-1221 Pro & Elite Only 1) Slide the handlebar post into the frame making sure the holes face the front of the bike. 2) Allow the post to go into the frame all the way in to level 1 and align the pop pin so it snaps into the hole then tighten the pop pin and test for steadiness. 3) Loosen the pop pin and raise the handlebar to its highest position and tighten the pop pin and test for steadiness. Page 6 of 9

Inhaltszusammenfassung zur Seite Nr. 8

Page 7 of 9Star Trac Product Support 800-503-1221 Removing the decal protective covers The bikes have protective clear decal covers to protect the decals from damage during packaging and shipping. Using your fingers only, carefully peel off the protective covers after assembly of the bike. Testing the bike Use this checklist to perform the bike test procedure to ensure the bike is operating properly. ¨ Recheck all bolts to make sure they are all tightened to the proper torqu

Inhaltszusammenfassung zur Seite Nr. 9

Page 8 of 9Star Trac Product Support 800-503-1221 WEB SITE http://support.startrac.com/ PHONE 800-503-1221 FAX 714-669-0739 EMAIL SUPPORT@STARTRAC.COM Copyright©, Star Trac 14410 Myford Road Irvine, CA 92606 New Spinner Bike Install Rev A PN 620-7493.doc Page 8 of 9