Inhaltszusammenfassung zur Seite Nr. 1
Installation Instructions
for Topload Washers
Inside.....................................
Washer Dimensions........................................................... 2
Before You Start................................................................ 2
Installation......................................................................... 3
Installer Checklist.............................................................. Back Cover
Date Purchased _____________________________
Model Number _________
Inhaltszusammenfassung zur Seite Nr. 2
Washer Dimensions 28 in. (71.1 cm) 22.13 in. (56.2 cm) .4 in. 26 in. (66 cm) 25.6 in. (65 cm) (10.2 mm) TLW2075N *With leveling legs turned into base. Figure 1 Parts Included Before You Start An accessories bag has been shipped inside your Supplies washer. It includes: For most installations, the basic supplies you will need • Two fill hoses with washers and filter screens. are: Refer to step 3 of Installation. � Four rubber feet. Refer to step 5 of Installation. 1 2 � Beaded strap. Refer t
Inhaltszusammenfassung zur Seite Nr. 3
Step 2: Wipe Out Inside of Washtub Installation Prior to first wash, use an all purpose cleaner, or a Step 1: Remove the Shipping Brace and detergent and water solution, and a damp cloth to Shipping Plug remove shipping dust from inside of washtub. Remove the shipping brace from under the lid. The shipping plug will be released from the base of the washer when removing the cardboard base from the washer. Refer to Figure 3. NOTE: Do not tilt washer to front or sides when moving. Save the sh
Inhaltszusammenfassung zur Seite Nr. 4
Step 3: Connect Fill Hoses Connecting Hoses Remove the two plain rubber washers and two filter screens from the accessories bag. Install them into WARNING each end of the fill hoses as shown in Figure 5. The Under certain conditions, hydrogen gas screen must be facing outward. may be produced in a hot water system Screw hose couplings with the filter screens onto the that has not been used for two weeks or water faucets until they are finger-tight. Then, using a more. HYDROGEN GAS IS EXP
Inhaltszusammenfassung zur Seite Nr. 5
IMPORTANT: Hoses and other natural rubber Standpipe Installation: parts deteriorate after extended use. Hoses may Place the adapter into the standpipe. develop cracks, blisters or material wear from the temperature and constant high pressure they are The recommended height for the standpipe is subject to. 36 inches (91.44 cm). Standpipes higher than 4 feet (122 cm) are not recommended. All hoses should be checked on a yearly basis for Remove the beaded strap from accessories bag and any v
Inhaltszusammenfassung zur Seite Nr. 6
If standpipe is lower than 36 inches (91.44 cm), you Laundry Tub Installation: must install No. 562P3 Siphon Break Kit. Refer to For this type of installation, the drain hose MUST be Figure 8. This kit is available (as optional equipment secured to the stationary tub to prevent hose from at extra cost) through an authorized dealer or parts disloding during use. Refer to Figure 10. Use the distributor. Installation instructions are supplied with beaded strap (supplied in accessories bag) t
Inhaltszusammenfassung zur Seite Nr. 7
Step 5: Position and Level the Washer Position washer so it has sufficient clearance for installation and servicing. 1 Place washer in position on a clean, dry and reasonably firm floor. Installing the washer on any type of carpeting is not recommended. For easier access to leveling legs, prop up washer with a wooden block. Refer to Figure 11. Place rubber feet (supplied in accessories bag) on all four leveling legs. Refer to Figure 12. 5 Place a level on the cabinet top and check if the
Inhaltszusammenfassung zur Seite Nr. 8
Step 6: Plug in the Washer When plugging in the washer: � DO NOT overload circuits. Washer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-Prong grounding plug. � DO NOT use an extension cord. Refer to serial plate for specific electrical � DO NOT use an adapter. requirements. � DO NOT operate both a washer and gas dryer on the same circuit. Use separately fused 15 Amp circuits. The washer is designed to be operated on a separate 2 branch, polarized, three-wire, e
Inhaltszusammenfassung zur Seite Nr. 9
Grounding Information Step 7: Add Water to the Washer The washer must be grounded. In the event of To prevent damage to pump, do not run washer before malfunction or breakdown, grounding will reduce the adding at least one quart water to the tub. If the washer risk of electric shock by providing a path of least is run before any water is added, the pump seal may resistance for electric current. overheat causing the pump to leak. Once installed, the water retained in the drain system from the
Inhaltszusammenfassung zur Seite Nr. 10
Step 8: Check Lid Switch Washer should stop agitating and spinning when lid is opened. W376I Figure 15 Step 9: Check Installation Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly. Run washer through one complete cycle to make sure it is operating properly. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 201958 10
Inhaltszusammenfassung zur Seite Nr. 11
Inhaltszusammenfassung zur Seite Nr. 12
Installer Checklist Fast Track for Installing the Washer (Refer to the manual for more detailed information) 1 • Remove the Shipping 5 � Position and LEVEL Brace and Shipping Level the Washer. D255I D255I Plug. CHECK CHECK W316I W316I TLW1975N TLW1975N 2 6 � Wipe Out Inside of � Plug in the Washer. Washtub. TLW2009N TLW2009N CHECK CHECK D254I D254I Filter Cold Valve 3 7 �Connect Fill � Add Water to Screens Connection Hoses. the Washer. COLD HOT Blue C H Red Hot Valve Connection Plain T
