Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION GUIDE
Undercounter Ice Machine
Inhaltszusammenfassung zur Seite Nr. 2
Contents Important Note Undercounter Ice Machine . . . . . . . . . . . . . . . . . . . . . 3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of Ice Machine Specifications . . . . . . . . . . . . . . . . . . . . . 4 highlighted information throughout this guide: Ice Machine Installation . . . . . . . . . . . . . . . . . . . . . . . . 8 IMPORTANT NOTE highlights information that is especially Installation Checklist . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
Undercounter Ice Machine 3 subzero.com/specs Sub-Zero Undercounter Ice Machine IMPORTANT NOTE: The importance of the installation of the Sub-Zero ice machine cannot be overemphasized. Proper installation requires connection to the water Installation must be completed by a qualified installer. supply, a drain and a dedicated electrical circuit. These connections are the responsibilities of the installer. Read this entire installation guide prior to installation. Improper connections can result in
Inhaltszusammenfassung zur Seite Nr. 4
Ice Machine Specifications 4 Ice Machine Specifications OVERALL DIMENSIONS INSTALLATION 3 14 /4" (375) 23" (584) TOP VIEW 24" (610) OPENING DEPTH 5 33 /8" (854) 4" (102) 1 1 24" (610) 34 /2" (876) 15 /4" OPENING DEPTH OPENING (387) HEIGHT OPENING WIDTH 18" (457) SIDE VIEW FRONT VIEW 6" (152) IMPORTANT NOTE: It is recommended that the electrical Overall dimensions do not include panels or handles. and water supply be placed in an adjacent cabinet. If they are placed within the opening, additional
Inhaltszusammenfassung zur Seite Nr. 5
Ice Machine Specifications 5 subzero.com/specs Electrical Requirements The ice machine must be installed with adequate clear- The electrical supply for the ice machine must be installed ance for electrical connection at the rear of the unit. The by a qualified electrician in accordance with all applicable electrical supply for the ice machine requires installation of national and local electrical codes. Observe the following: a grounded receptacle on a separate circuit, servicing only • The ice
Inhaltszusammenfassung zur Seite Nr. 6
Ice Machine Specifications 6 Plumbing Requirements The ice machine must be installed with adequate clear- WATER SUPPLY LINE ance for water and drain connections at the rear of the For all ice machine models, locate the water supply line as unit. Prepare the water supply line and drain connection shown in the illustration below. before installing the ice machine. IMPORTANT NOTE: It is recommended that the water supply be placed in an adjacent cabinet within the shaded area shown in the illustrati
Inhaltszusammenfassung zur Seite Nr. 7
Ice Machine Specifications 7 subzero.com/specs Plumbing Requirements DRAIN CONNECTION • The ice machine drain connection is approximately 5" (127) from the floor. Models UC-15I and UC-15IO are gravity drain models that require a drain tube that is pitched down from the outlet at • For the gravity drain, all horizontal runs of drain lines 1 the back of the unit to the sanitary sewer connection. must have a /4" (6) per 12" (305) fall. Models UC-15IP and UC-15IPO have a built in drain pump • Drain
Inhaltszusammenfassung zur Seite Nr. 8
Ice Machine Installation 8 Installation Requirements Installation • Installation must allow removal of the ice machine for Before moving the ice machine into position, make sure all cleaning and service. Service diagnostics are per- opening dimensions, electrical and plumbing requirements formed from the top of the ice machine. are complete and accurate. The floor under the ice machine must be at the same level as the surrounding • If the ice machine is installed in a corner, the door finished f
Inhaltszusammenfassung zur Seite Nr. 9
Ice Machine Installation 9 subzero.com/specs Installation INSTALL THE ICE MACHINE 8) Move the ice machine into its final position. 1 1) Adjust the leveling legs close to the desired height. 9) Secure the ice machine by installing two #8 x /2" flat Refer to the illustration below. head screws through each hinge. Refer to the illustra- tion below. 2) Reverse the door swing if needed. Refer to steps outlined on the following pages. 10) Add 4 oz (115 ml) of undiluted ice machine cleaner to a contain
Inhaltszusammenfassung zur Seite Nr. 10
Ice Machine Installation 10 Reverse Door Swing The hinged side of the door may be reversed to the other 2) Remove the hinges from the door by removing the four side if needed. screws (two per hinge) that secure the hinges to the door. Refer to the illustration below. The ice machine is shipped with the door hinged at the right. The door and hinges are designed for placing the 3) Remove the right-hand upper trim (shaded area) from hinges on either the right or the left side of the unit. the door
Inhaltszusammenfassung zur Seite Nr. 11
Ice Machine Installation 11 subzero.com/specs Reverse Door Swing 5) Remove the ice machine top cover by removing the 8) Remove two screws from the lower edge of the bottom two screws along the back of the unit. Refer to the trim plate and slide the trim plate to the right, to cover illustration below. the right-hinge mounting screw holes. The left-hinge mounting screw holes will now be exposed. Refer to 6) Remove four screws from the front top rail. Refer to the the illustration below. illustrat
Inhaltszusammenfassung zur Seite Nr. 12
Ice Machine Installation 12 Panel Installation DOOR PANEL INSTALLATION Door Panel Specifications Panel Width 15" (381) You should be sure of the door panel size and placement 3 before proceeding with the installation. Refer to the chart Panel Height 30 /8" (772) 5 for panel specifications. If you have questions, contact Minimum Thickness /8" (16) your authorized Sub-Zero dealer or cabinet supplier. Maximum Weight 15 lbs (7 kg) 1 For door handle hardware, a D-style pull, centered on the (3) Dimen
Inhaltszusammenfassung zur Seite Nr. 13
Ice Machine Installation 13 subzero.com/specs Panel Installation Installation INSTALL KICKPLATE Once the ice machine is in position, install the kickplate Exercise caution when drilling holes for mounting hardware. This is especially critical with inset panels. using the screws provided. The kickplate must be removed for servicing. The floor cannot interfere with removal. Do not cover the vents of the kickplate to allow proper airflow. The door panel may hang in front of the vents, but a decorat
Inhaltszusammenfassung zur Seite Nr. 14
Ice Machine Installation 14 Installation Installation Checklist 90° DOOR STOP To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure Door stop pins provided with the ice machine will limit the that no part of the installation has been overlooked. door swing to 90°. Follow these steps to install: 1) Open the door to approximately 80°. INSTALLATION CHECKLIST 2) Insert the stop pin into the bottom door hinge (pin Have all electrical and wate
Inhaltszusammenfassung zur Seite Nr. 15
Service Information 15 subzero.com/specs Service Information If service is necessary, maintain the quality built into your ice machine by calling Sub-Zero factory certified service. If you are storing or disposing of your old refrigerator For the name and number of Sub-Zero factory certified or freezer, please do it safely. Remove the service nearest you, check the contact & support section doors or tightly secure of our website, subzero.com or call Sub-Zero customer the doors closed. care at 80
Inhaltszusammenfassung zur Seite Nr. 16
SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7024818 REV-A 2/2012
