Inhaltszusammenfassung zur Seite Nr. 1
Operation/Maintenance
Combination
Sleever, Bosom,
Body and Yoke Press
CSBBYMV
CAB438C
CAB438C
WARNING
Read and understand these instructions
before operating or servicing these machines.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
An LSG Company
831 South First Street, P.O. Box 32270
Louisville, KY 40232-2270
Phone: (502) 587-1292
Sales Fax: (502) 585-3625
www.cissellmfg.com
Service/Parts Fax: (502) 681-1275
Par
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Safety Information.............................................................................. 3 Table of Explanation of Safety Messages........................................................... 3 Important Safety Instructions ............................................................... 3 Contents Operation............................................................................................. 5 Front View of CSBBYMV ...................................................................
Inhaltszusammenfassung zur Seite Nr. 4
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ0975 2
Inhaltszusammenfassung zur Seite Nr. 5
Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING,” Save These Instructions and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These WARNING precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the Failure to install, maintain, and/or operate machine. this machine according to manufacturer’s instructions may result in
Inhaltszusammenfassung zur Seite Nr. 6
Safety Information 9. Use press only for its intended purpose, finishing NOTE: The WARNINGS and IMPORTANT garments. SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible 10. ALWAYS disconnect the press from electrical conditions and situations that may occur. Common supply before attempting any service. Disconnect sense, caution and care must be exercised when the power cord by grasping the plug, not the cord. installing, maintaining, or operating the press. 11.
Inhaltszusammenfassung zur Seite Nr. 7
Operation Front View of CSBBYMV 6 2 4 3 5 1 7 8 9 10 CAB697N 12 11 14 13 CAB697N 1 Left End Guard 8 Sleeve Blower 2 Sleeve Extender Arms 9 Heat Exchanger, Buck Air Bags 3 Buck 10 Heat Exchanger, Sleeves 4 Mirror 11 Electrical Control Panel 5 Safety Bars 12 Front Head 6 Water Spray Gun 13 Operator Control Buttons 7 Electrical Box 14 Adjustable Air Valves Figure 1 AJ0975 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5
Inhaltszusammenfassung zur Seite Nr. 8
Operation Rear View of CSBBYMV 1 2 3 11 9, 10 4 8 CAB83N 5 6 7 CAB83N 1 Exhaust Muffler 7 Blower, Buck Air Bags 2 Rear Head 8 Steam Inlet 3 Left End Guard 9 OSHA Approved Shut-Off Valve at Air Inlet 4 Air Intake Filters 10 Air Inlet, Filter, Regulator and Lubricator 5 Steam Solenoid Valve, Sleeves 11 Sleeve Blower 6 Steam Condensate Tank, Sleeves Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ0975 6
Inhaltszusammenfassung zur Seite Nr. 9
Operation Operating Controls and Indicators 22 1 21 20 2 19 3 18 4 CAB89N CAB89N 17 5 16 15 6 14 13 SEE DETAIL ABOVE 15 CAB698N CAB698N 7 8 9 10 12 11 Figure 3 AJ0975 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7
Inhaltszusammenfassung zur Seite Nr. 10
Operation Operating Controls and Indicators Refer to Figure 3. Controls or Function Position or Indication Indicators 1. Red stop button Stops electrical service to blowers, timers, and heat exchanger. Press to actuate. 2. Cycle timer control Determines pressing cyle time. Rotate knob to desired knob setting. 3. Steam timer control Determines the length of sleeve steaming time. Normally set at Rotate knob to desired knob 5 seconds. setting. 4. Water gun needle Turns water on and off to water
Inhaltszusammenfassung zur Seite Nr. 11
Operation Table 1 (Continued) Controls or Function Position or Indication Indicators 15. Sleeve extender Clamp cuffs and extend sleeves outward for high quality finish. Extend shirt sleeves via rods foot pedal (item 11). Retract sleeve extender arms via sleeve extender button (item 12). 16. Collar clamp Holds shirt collar in place on buck (refer to item 10). Open and close clamp with foot pedal (item 10). 17. Safety bars Exhausts entire air system except air to collar clamp air cylinder. S
Inhaltszusammenfassung zur Seite Nr. 12
Operation Resetting Air Circuit Pressing Short Sleeve Shirts The air circuit must be reset before press can be used. Sleeve extender arms are not used when a short sleeve Resetting is required if: shirt is dressed on the buck. The operator should turn the steam timer selector switch to the off position to ● Press has been shut down. stop live steam and sleeve blower air through sleeve ● Any safety bar or red emergency stop button has armhole. been activated. ● Gauge indicates 0 air pressure.
Inhaltszusammenfassung zur Seite Nr. 13
Operation Operating Instructions WARNING These instructions will provide the best shirt pressing quality and prolong padding life. To avoid possible serious injury NEVER use press unless BOTH safety bars are Pre-Operating Services working properly. W375 Perform the following services daily before using the press: 8. Reset air to press. Send buck into cabinet. Allow buck to travel into cabinet and heads to close. 1. Check condition of buck padding and air bags. Press emergency stop button.
Inhaltszusammenfassung zur Seite Nr. 14
Operation Post-Operating Services Cleaning Press Heads Perform the following services after the final operation Press heads require cleaning if: of the day or anytime press will be idle for an extended ● Discoloration transfers from head to shirts. period of time: ● Shirts stick to heads as the heads open. 1. Turn off steam to buck sleeve openings by pressing the steam Timer Selector switch to the Once precautions listed in these WARNINGS have off position. been met, follow directions provide
Inhaltszusammenfassung zur Seite Nr. 15
Operation CSBBYMV Operation Sequence 5. Unload CUCC. Hang shirt 2 on garment hook. 6. Load shirt 3 from damp box onto CUCC. Single Operator. Refer to Figure 4. 7. Remove shirt 1 from buck. Place on collar post. A typical single operator shirt station consists of: Form collar and button. Leave shirt on collar post ● One CSBBYMV sleeve, bosom, body and yoke to cure. press 8. Load shirt 2 from garment hook onto buck. ● One collar and cuff press (CUCC) 9. Unload CUCC. Hang shirt 3 on garment hook
Inhaltszusammenfassung zur Seite Nr. 16
Operation Buck Dressing Instructions 4. Depress collar clamp foot pedal to open collar clamp. Slide index finger of each hand along The steps listed below outline the procedure for neck band from the top down to the points of the dressing a shirt on the buck. collar. Guide left collar point under right point. Butt neck band ends together. Do NOT overlap 1. Grasp shirt by neck band with label side facing band ends except for large size shirts. Refer to you. Turn to buck and swing the rig
Inhaltszusammenfassung zur Seite Nr. 17
Operation 6. Grasp one sleeve with gusset facing you. Overlap NOTE: Dress sleeve into clamp at CUFF SEAM. gusset of cuff as if you are going to button cuff so Do NOT place cuff in clamp. Loading cuff into that air does not escape gusset. The sleeve end is clamp will pinch or crease the cuff. A guide on each now closed (do not button). Refer to Figure 9. clamp will cause you to meet resistance if cuff is accidentally loaded. Refer to Figure 11. CAB478N Figure 11 CAB421N Figure 9 NOTE: Do N
Inhaltszusammenfassung zur Seite Nr. 18
Operation 8. Press the left foot pedal to extend the sleeves and turn the buck vacuum on. 9. Notice a natural “A” at shirt’s placket. The gap at the bottom is related to shirt size. The larger shirts will have a smaller gap. Refer to Figure 13. CAB423N CORRECT Figure 14 11. With thumb and first finger of both hands, grasp the bottom of the placket and side seam at the left side of the shirt. Gently pull downward. Pull the placket downward in the direction of the natural “A.” This action
Inhaltszusammenfassung zur Seite Nr. 19
Operation 13. Spray with water gun if necessary. Refer to Figure 15. CAB424N Figure 15 14. If necessary, move your hand in an upward direction over the pocket to remove any air trapped inside. Refer to Figure 16. CAB426N Figure 17 17. Press right foot pedal to release collar clamp. Lift right side of shirt. Move right shoulder clear of buck with a slight upward then backward motion of your hand. Do not swing your right arm over the buck (that would be unnecessary motion). Refer to Fig
Inhaltszusammenfassung zur Seite Nr. 20
Operation 18. Using your left hand, grasp the left sleeve just Operating Tips next to the yoke. Pull the shirt to your left and off the buck. As the right side of shirt clears the Shirt Quality buck, position the fingers of your right hand so The CSBBYMV gives a high volume professional they catch the left side of shirt and slide to the finish to sleeves, bosom, body, sides and yoke of right of the yoke. This opens the shirt and shirts. To achieve best shirt quality and volume: supports i
