Inhaltszusammenfassung zur Seite Nr. 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY
THIS MANUAL IS PRINTED ON RECYCLED PAPER
828
By SHERWOOD INDUSTRIES LTD.
B Vent
OWNERS MANUAL
Installation And Operating Instructions For Models:
828 BV. FS. (Freestanding)
828 BV. INS. (Insert)
WARNING
WHAT TO DO IF YOU SMELL GAS
If the information in this
• Open windows/Extinguish any open flame
manual is not followed exactly,
• Do not try to light any appliance.
a fire or explosion may result
•
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY PRECAUTIONS FOR SAFE INSTALLATION AND OPERATION OF YOUR "ENVIROGAS" ROOM HEATER, PLEASE, CAREFULLY READ THE FOLLOWING INFORMATION: • All "ENVIROGAS" gas-fired appliances must be CAN/CGA -B149 installation code in Canada or the National Fuel Gas Code ANSI Z223.1.2 in the installed in accordance with these instructions. Carefully read all the instructions in this manual first. USA. Consult the building authority having jurisdiction to determine the need for a permit prior to
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS 1 Code Approvals................................................................................................................................... 3 2 Specifications..................................................................................................................................... 3 3 Dimensions and Clearances to Combustibles ....................................................................................... 4 4 Deciding where to locate your stove.....
Inhaltszusammenfassung zur Seite Nr. 4
FOR INSTALLATIONS ABOVE 2000 FEET • In Canada, these appliances are certified for altitudes of 0-2,000 feet and must be derated by 10% for installation at elevations between 2,000 and 4,500 feet. • In the USA, these appliance are certified for elevations up to 2,000 feet. For elevations above 2,000 feet, input should be reduced 4% for each 1,000 feet above sea level. The efficiency rating of this appliance is a product thermal efficiency rating determined under continuous operating
Inhaltszusammenfassung zur Seite Nr. 5
4. DECIDING WHERE TO LOCATE YOUR FREESTANDING STOVE 1. The stove should be located out of traffic and away from furniture and draperies. 2. This stove should have sufficient access for its safe operation and maintenance. 3. Locate a position where the flue system of the stove can be properly installed without damaging the integrity of the building. e.g. cutting wall or ceiling joists. 4. The stove can be installed on any wooden or non-combustible flat surface extending the full width a
Inhaltszusammenfassung zur Seite Nr. 6
* As specified in CGA B149 Installation Codes (1991) Note: Local Codes or Regulations may require different clearances. 5. ASSEMBLY AND INSTALLATION INSTRUCTIONS PREPARATION FOR INSTALLATION • Remove the packaging from the appliance, pedestal or surround panels, check to make sure there is no damage. Carefully check the glass door. Do not use the unit if it is damaged. In the event damage is found please report it to both the courier and your dealer as soon as possible. ASSEMBLING
Inhaltszusammenfassung zur Seite Nr. 7
13. Re-attach the hinged side flaps by sandwiching the surround panels between the mounting brackets and the hinged side flaps. secure with screws. 14. Re-install the stove top by inserting the locating screws, previously put into the surround panel top, through the holes in the back of the stove top. Push threaded studs through holes in top baffle and tighten nuts. Re-attach the top grill bar. 15. Be sure to maintain adequate clearances around air openings, do not block. 16. P
Inhaltszusammenfassung zur Seite Nr. 8
6. ELECTRICAL REQUIREMENTS The ENVIROGAS 828 Series will operate without an external electrical power supply. This model has a Millivolt gas control which uses the pilot flame to generate enough electricity to operate the main burners. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. FAN INSTALLATION OPTIONAL FAN Efficiency and heat output of the unit
Inhaltszusammenfassung zur Seite Nr. 9
7. GAS LINE CONNECTION AND TESTING WARNING: Only persons licensed to work with gas piping can make the gas connections to this appliance. This appliance is equipped with a 3/8” stainless steel flex line from the valve. This line may be routed through the hole in the rear of the pedestal, or on inserts, routed through the fire box sides. An adapter plate is available for installations that do not allow flex pipe through cabinetry. NOTE: Consult your local authorities and in CAN. the CAN/
Inhaltszusammenfassung zur Seite Nr. 10
8. VENTING WARNING: THIS APPLIANCE HAS BEEN DESIGNED TO OPERATE BY DRAWING COMBUSTION AIR AND DILUTION AIR FROM THE ROOM. IT IS ALSO DESIGNED TO DRAW ROOM AIR FOR PROPER HEAT CIRCULATION FROM THE SIDES OF THE UNIT. BLOCKING OR MODIFYING THE LOUVERS IN ANY WAY CAN CREATE HAZARDOUS SITUATIONS, EITHER THROUGH POOR VENTING OR BY OVERHEATING. IT IS IMPORTANT THAT THIS UNIT HAS SUFFICIENT AIR CIRCULATION FOR PROPER VENTING AND COMBUSTION. PROVISIONS MUST BE MADE FOR THE SUPPLY OF ADEQUATE CO
Inhaltszusammenfassung zur Seite Nr. 11
constructed out of non-combustible materials. Make sure that all chimney clean outs are tightly fitting and will not permit air to leak into the chimney. Remove the vent collar plate from the top of the insert and connect it securely with at least 3 sheet metal screws and a 4" hose clamp. Check for any tears in the liner at this point. (See also Assembly and Installation Instructions section 5 ) IMPORTANT: The screw that holds the vent collar plate in it's approved position must be inst
Inhaltszusammenfassung zur Seite Nr. 12
For best venting performance, we recommend total If 45° elbows are used, one 90° elbow is equivalent vent height of 10ft (3m) to 30ft (9m). Total to two 45° elbows. horizontal length depends on the number of elbows Venting rise should be a minimum of 3 ft (.62m). used. The venting should never slope down. 1/4" from the top of the unit before any horizontal. rise per 2' horizontal is recommended. For other special venting requirements, please refer If practical, it is best have short
Inhaltszusammenfassung zur Seite Nr. 13
10. INSTALLATION OF LOG SET and EMBERS A. INSTALLING THE GLOWING EMBERS A bag of ceramic fiber embers is provided for use on the front burner tray. CAUTION: Use only the type of ember material supplied with this appliance. Due to the irregular size of the ember material there may be more than required. The use of other foreign materials on the burners may create dangerous conditions. If over time, through cleaning and servicing these embers require replacement, contact your
Inhaltszusammenfassung zur Seite Nr. 14
11. OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE OPERATING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A) This appliance is equipped with a pilot which must be lit • If you cannot reach your gas supplier, call the fire by hand by following these instructions exactly. department. B) BEFORE LIGHTING smell all around the appliance area for C) Use only your hand to push in or tu
Inhaltszusammenfassung zur Seite Nr. 15
12. ROUTINE MAINTENANCE Periodically check to ensure that the "B-Vent" venting replacement door assembly including glass must system is clear and that a negative draft is present be fitted. when the unit is operating. On fireplace insert models To Replace there is a draft inspection tube the opening is located • open door fully on the right hand side behind the hinged side. A • Lift door vertically so that hinge pins lift out vacuum should be present at the opening. of hinge receivers.
Inhaltszusammenfassung zur Seite Nr. 16
13. TROUBLE SHOOTING Problem Possible Cause Solution Spark will not arc to the pilot after Defective piezo ignitor Check connections to ignitor repeated pressing of spark ignitor -If ignitor connections are good but there is no spark-replace ignitor Broken spark electrode -Check for broken ceramic insulation replace, electrode if broken Miss-aligned spark electrode -If spark is not arcing from the electrode to pilot- adjust by loosening screws on pilot base. Adjust away from
Inhaltszusammenfassung zur Seite Nr. 17
14. PARTS AND ACCESSORIES Service Parts available from your local ENVIROGAS Dealer. PART # DESCRIPTION 828-001 Convection Blower 828-002 Heyco Strain Relief 828-003 2-Speed Fan Switch 828-004 Eurosit Manually Regulated Valve, Natural Gas 828-005 Eurosit Manually Regulated Valve, Liquid Propane 828-006 Pilot with Ingitor Electrode, Natural Gas 828-007 Pilot with Ingitor Electrode, Liquid Propane 828-008 Thermocouple 828-009 Thermocouple Interrupter 828-014 120 Ceramic Fan Temp Sen
Inhaltszusammenfassung zur Seite Nr. 18
15. WARRANTY Sherwood Industries Ltd. offers a *Lifetime Warranty on this gas product. The lifetime warranty covers the appliance for a period of seven years from the date of installation. This warranty applies only to the original owner in the original location Covered under the lifetime warranty are Cabinet Sides, Tops, Pedestals, Surround Panels and Chassis and Heat Exchanger. These steel components are covered against manufacturer’s defects for 5 years and labor for the first yea
Inhaltszusammenfassung zur Seite Nr. 19
16. INSTALLATION DATA SHEET The following information must be recorded by the installer for warranty purposes and future reference. Envirogas Model: EG-828 INSERT BV. FPI Name of Owner: Name of Dealer: __________________________________________ ___________________________________________ Address: Address: __________________________________________ ___________________________________________ __________________________________________ ________________
Inhaltszusammenfassung zur Seite Nr. 20
20
