Inhaltszusammenfassung zur Seite Nr. 1
P5755
IMPORTANT!
KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fi sher-price.co.uk
Inhaltszusammenfassung zur Seite Nr. 2
Consumer Information IMPORTANT! Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child's reach. WARNING • Please read these instructions before assembly and use of this product. Prevent serious injury or death from • Adult assembly is required. falls or sliding out: • Tool needed for assembly: Phillips Screwdriver (not included). • The child should at all times wear a • Product features and decorations may vary from th
Inhaltszusammenfassung zur Seite Nr. 3
Assembled Parts CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Pad Seat Back Seat Bottom 2 Frames Hinge Rod Back Base Front Base 2 Seat Bottom Tubes Footrest Food Tray Base Tray Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. #8 x 1,9 cm Screws – 8 #10 x 2,2 cm Black Screw – 7 Shown Actual Size 3
Inhaltszusammenfassung zur Seite Nr. 4
Assembly IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. ® DO NOT use if any parts are missing or broken. Contact Fisher-Price for replacement parts and instructions if needed. Never substitute parts. Footrest Seat Bottom 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. Plastic Rings 3 • Align the holes in the plastic rings and the seat bottom t
Inhaltszusammenfassung zur Seite Nr. 5
Assembly Insert Screws Here Hinge Hinge Rod 4 6 • Insert two #10 x 2,2 cm black screws through the footrest and • Turn the seat assembly face down. into the seat bottom. Tighten the screws. This may require • Insert the hinge rod through the hinge on the seat back and seat extra force. bottom, as shown. • Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten the screw. Seat Back Pin • Set the seat assembly aside for Assembly step 9. Slot Slot Seat Bottom Assembly 5 • Turn the sea
Inhaltszusammenfassung zur Seite Nr. 6
Assembly Frame Leg Seat Height Adjusters Position 4 Frame Decorated Side Frame Back Legs Press Lever 8 • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Seat Assembly Base Screw Retainers Sockets Sockets 7 S Seat Bottom T eat Bottom Tubes ubes • Pull the frame leg out on each frame to open. Make sure it "clicks" into place. • Position a frame so that the decorated side is outward. • Fit the end of a base into the back leg o
Inhaltszusammenfassung zur Seite Nr. 7
Assembly Seat Height Adjuster Screw Retainers Base 10 Seat Bottom Tube Ends • Fit the frame front legs onto the remaining base. • Fit a screw retainer over a hole in the front leg. 12 • Insert a #10 x 2,2 cm black screw through the screw retainer and front leg. Tighten the screw. • Repeat this procedure to secure the other end of the base with • Push each seat height adjuster to be sure they are completely on the remaining screw retainer and #10 x 2,2 cm black screw. the seat bottom tubes.
Inhaltszusammenfassung zur Seite Nr. 8
Assembly Pad Slot Elastic Loops Hole Hole Crotch Belt FRONT VIEW 14 • Insert the crotch belt through the slot in the pad. Make sure the Tabs crotch belt is not twisted. Elastic Loops BACK AND BOTTOM VIEW 13 • Lift the bottom of the pad. Insert the two elastic loops on the pad through the holes in the seat bottom. • From the back and bottom of the seat, hook the elastic loops to the tabs on the seat. 8
Inhaltszusammenfassung zur Seite Nr. 9
Assembly Upper Shoulder Belt Slots Shoulder Portion Shoulder Portion L Lower Shoulder Belt Slots ower Shoulder Belt Slots 15 • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by 17 feeding them through the slots in the seat back. • Insert the shoulder portion of the shoulder/waist belt through the slots in the pad and seat back. - Use the lower shoulder belt slots for a smaller baby. - Use the upper shoulder belt slots for a larger baby. • Fit the
Inhaltszusammenfassung zur Seite Nr. 10
Secure Child WARNING Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • Do not use the high chair unless all com- ponents are correctly fitted and adjusted. Waist/Shoulder Belt Waist/Shoulder Belt 2 • Tighten each waist belt and shoulder belt so that the restraint system is snug against your child. Please refer to the next section for
Inhaltszusammenfassung zur Seite Nr. 11
Secure Child Hold Adjuster Shoulder Portion Pull Down Strap Slide Adjuster Down TIGHTEN LOOSEN 4 6 To tighten the shoulder belts: Hold the adjuster and pull the front • From the front of the high chair , pull the shoulder portion of shoulder strap down. the waist/shoulder belts out and then fit them back through the To loosen the shoulder belts: Slide the adjuster down. desired shoulder belt slots in the headrest pad, seat pad and the Note: After adjusting the restraint system to fit your ch
Inhaltszusammenfassung zur Seite Nr. 12
Using the Trays WARNING Prevent serious injury or death from falls or sliding out. The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. Base Tray 8 • While pushing the release bar on the front of the base tray , Armrest adjust the base tray forward or backward. Armrest 7 • Fit the base tray onto the seat armrests. Push down until the base tray "snaps" into place. Hint: Before use, thoroughly wash all p
Inhaltszusammenfassung zur Seite Nr. 13
Using the Trays Food Tray Base Tray 9 10 • While pushing the release bar on the front of the base tray, • Fit the food tray into the base tray, as shown. pull the tray base towards you and remove. Hint: Before use, thoroughly wash all parts (the trays) that may contact food. The food tray is not microwave safe. 13
Inhaltszusammenfassung zur Seite Nr. 14
Adjusting the Seat Hint: Adjust the seat height to any of seven positions! WARNING Prevent serious injury or death from falls or sliding out: It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position. Hint: Adjust the seat angle to any of three positions: Upright, Semi-Recline or Recline. Upright Semi-Recline Press Lever Recline 12 To adjust the seat height: • Press the levers on both seat height adjusters and lift or lower the s
Inhaltszusammenfassung zur Seite Nr. 15
Storage Care • The restraint system, pad, frame, trays and tray toy may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Pull Frame Release Latch • The food tray is also top rack dishwasher safe (or use bottom rack - without using the drying cycle). To remove the pad: • Remove the elastic loops from the pegs on the back of the seat. • From behind the product, squeeze the restraint release tabs and remove the restraint system from the peg. • From the fro
Inhaltszusammenfassung zur Seite Nr. 16
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303. www.service.mattel.com/uk. Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867. Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2008
