Inhaltszusammenfassung zur Seite Nr. 1
Multi-Purpose Oscillating Tool
Operator’s Manual
Outil oscillant à usages multiples
Manuel d’utilisation
Herramienta oscilante multiuso
Manual del Operario
GMT15A
Inhaltszusammenfassung zur Seite Nr. 2
Multi-Purpose Oscillating Tool 1.5 AMP Operator’s Manual Specifications: • Model: GMT15A • Ra ted Input: 120V~AC, 60HZ, 1.5A • No Load Speed: 21,000/min (OPM) Includes: Oscilla ting T ool, Hook & Loop Sanding P ad, Assorted Sandpa per , Rigid Scra per Blade, 1-3/16" (30mm) E-Cut (Flush Cut) Sa w Blade, 3” W ood & Dr ywall Sa w Blade, and Wrench WArnIng: To reduce the risk of injury, user must read and understand this operator’s manual before operating this tool.
Inhaltszusammenfassung zur Seite Nr. 3
WArnIng: rEAD AnD UnDErSTAnD ALL WArnIngS, CAUTIOnS AnD OPErATIng InSTrUCTIOnS BEFOrE USIng THIS EQUIPMEnT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS WORK AREA SAFETY: • Keep your work area clean and well lit . Cluttered benches and dark areas invite accidents. • Do not operate power tools in explosive atmospheres , such as in the presence of flammable liquids, gases, or dust. P o
Inhaltszusammenfassung zur Seite Nr. 4
• Do not for ce the power tool. The tool will perform the job better and safer a t the feed ra te for which it is designed. F orcing the tool could possibly dama ge the tool and may result in personal injur y . • Use the corr ect power tool for the job. Don’t force the tool or a ttachment to do a job for which it is not designed. • Do not use tool if switch does not tur n it on or of f. An y tool tha t cannot be controlled with the s witch is dangerous and must be repaired or replace
Inhaltszusammenfassung zur Seite Nr. 5
EXTEnSIOn COrDS grounded tools require a three wire extension cord . Double insula ted tools can use either a two or three wire extension cord. As the distance from the po wer supply outlet increases, you must use a hea vier gauge extension cord. using extension cords with inadequa tely sized wire causes a serious drop in volta ge, resulting in loss of po wer and possible tool dama ge. Refer to the table sho wn belo w to determine the required minimum wire size. The smaller the gauge
Inhaltszusammenfassung zur Seite Nr. 6
WArnIng: USE OF THIS TOOL CAn gEnErATE AnD DISBUrSE DUST Or OTHEr AIrBOrnE PAr TICLES, InCLUDIng WOOD DUST, Cr YSTALLInE SILICA DUST AnD ASBESTOS. Direct particles away from face and body. Always operate tool in a well-ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the d
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY AnD ADJUSTMEnTS WArnIng: Always be sure that the tool is switched off and unplugged before adjusting, adding accessories, or checking a function on the tool To install the saw blade or scraper blade 1. Loosen and remove the ca p screw (a) and large blade washer from the shaft flange using Allen wrench provided. (FIG 1) 2. Place the accessor y over the shaft flange (b). The shaft flange of this tool comes with a 4-pin design. Make sure the holes on the accessor y properly e
Inhaltszusammenfassung zur Seite Nr. 8
APPLICATIOnS nOTE: This tool must be used only with gEnESIS oscillating tool accessories. See Accessories Chart for details. This multi-purpose oscilla ting tool is intended for cutting and sanding wood, plastic, plaster and non-ferrous metals. It is especially suitable for cutting in tight spaces and for flush cutting. F ollo wing are a few typical uses. Cutting: use a flush cutting sa w blade (or “e-cut blade”) for making precise cuts in tight areas, c lose to edges or flush to a s
Inhaltszusammenfassung zur Seite Nr. 9
ACCESSOrIES nOTE: This tool must be used only with gEnESIS oscillating tool accessories. Model Picture Description Recommended Application Flush Cut Saw Blade Assortment Cutting and flush cuts in Wood, Plastic, Drywall and Pack, other soft materials. Size: 3/8" (10mm), For example: Size: 3/4" (20mm), -Flush cutting door jamb or base molding. Size: 1-3/16" (30mm) -Cut-outs in furniture for cable connections. GAMT301 Cutting in Wood, Plastic, Drywall and other Soft Materials. 3" Wood & Drywal
Inhaltszusammenfassung zur Seite Nr. 10
Notes
Inhaltszusammenfassung zur Seite Nr. 11
Notes Notes
Inhaltszusammenfassung zur Seite Nr. 12
Richpower Industries, Inc. 736 Hampton Road Williamston, SC USA www.richpowerinc.com
