Bedienungsanleitung Harbor Freight Tools 90160

Inhaltszusammenfassung zur Seite Nr. 1

4 TIER STOCKER
SERVICE CART
90160
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2003 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353

Inhaltszusammenfassung zur Seite Nr. 2

Specifications Weight Capacity 450 Lbs.Overall (if evenly distributed), 112 Lbs. Per Shelf Overall Dimensions 60” H x 39” L x 24-1/8” W Tray Dimensions 35-1/8” x 22-7/8” (Inside) Castors (4) 5” x 1-3/4” - (2 Swivel Castors) Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the m

Inhaltszusammenfassung zur Seite Nr. 3

9. Maintain products with care. Keep the Cart clean for better and safer performance. The handle must be kept clean, dry, and free from oil and grease at all times. 10. Stay alert. Watch what you are doing, use common sense. Do not operate the Cart when you are tired. 11. Check for loose and damaged parts. Before using the Cart, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and bindin

Inhaltszusammenfassung zur Seite Nr. 4

Assembly While following the assembly instructions on page 5, use the three FIGURES below and the Assembly Drawing on page 7. FIGURE 1 A Position 1 C G A H Note: Part Names are listed on page 6. B E D F Handle Detail FIGURE 3 FIGURE 2 Caster Plate Upper/Middle Tray (A) Post (C) Handle (H) Castor Mounting Plate (D) SKU 90160 Page 4

Inhaltszusammenfassung zur Seite Nr. 5

Assembly (continued) Note: You will need a 7/16” open end wrench and a flat screwdriver (both not included). Refer to FIGURES 1, 2, & 3, on page four and the Assembly Drawing on page 7. 1. Bolt the Bottom Tray (B) to all four Posts (C) using (16) 1/4-20 x 1/2” machine screws and nuts. 2. Working your way up the Posts (C) from the bottom, attach the two middle Upper/Middle Trays (A) to the posts using (16) 1/4-20 x 1/2” machine screws and nuts per tray. Do not attach two of the bolts on each

Inhaltszusammenfassung zur Seite Nr. 6

Parts List Part No. Description Qty. A Upper/Middle Tray 3 B Bottom Tray 1 C Post 4 D Castor Mounting Plate 2 E Rigid Castor 2 F Swivel Castor 2 G Handle Bracket 2 H Handle Tube 1 I Hardware Package 1 Maintenance 1. Periodically tighten all of the hardware. 2. Make sure the castors are free of all dirt, debris, or grease. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR

Inhaltszusammenfassung zur Seite Nr. 7

Assembly Drawing Detail (B) (D) Castor Plate Split Washer Nut SKU 90160 Page 7