Inhaltszusammenfassung zur Seite Nr. 1
DRT 900
Owner's Manual / 96093000801 / 2009-04
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers • Never operate the tiller without proper guards, plates, TRAINING or other safety protective devices in place. • Read the Manual care ful ly. Be thor ough ly fa mil iar with the controls and the proper use of the equip ment. • Keep children and pets away. Know how to stop the unit and disengage the controls • Do not overload the machine capacity by attempting quickly. to till too deep at too fast a rate. • Nev
Inhaltszusammenfassung zur Seite Nr. 3
CUSTOMER RESPONSIBILITIES PRODUCT SPECIFICATIONS • Read and observe the safety rules. Gasolina Capacity: 3 Quarts (2.8L) • Follow a regular schedule in maintaining, caring for Unleaded Reg u lar and using your tiller. Oil (API-SG-SL): SAE 30 (Above 32°F) • Follow instructions under “Maintenance” and “Stor age” (Capacity: 20 oz./0.6L) SAE 5W-30 (Below 32°F) sections of this Owner’s Manual. Spark Plug : NGK-BPR6ES WARNING: This unit is equipped with an internal com- (Gap: .030"/0.7
Inhaltszusammenfassung zur Seite Nr. 4
ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY FRONT A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) Utility knife (1) Tire pressure gauge (1) Pair of pliers LEFT RIGHT
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY • Grasp handle assembly. Hold in “up” position. Be sure UNPACKING CARTON (See Fig. 2) handle lock remains in gearcase notch. Slide handle assembly into position. CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material. HANDLE ASSEMBLY "UP" POSITION IMPORTANT: WHEN UN PACK ING AND ASSEM BLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES. TIGHTEN HANDLE LOCK • While holding handle assembly, cut cable ties se cur ing LEVER TO HOLD handle as
Inhaltszusammenfassung zur Seite Nr. 6
ASSEMBLY CONNECT SHIFT ROD (See Fig. 7) ATTACH CLUTCH CABLE (See Fig. 6) • Insert end of shift rod into hole of shift lever indicator. • Hook end of clutch cable through hole in control bar bracket. • Insert hairpin clip through hole of shift rod to secure. SHIFT HAIRPIN CONTROL BAR SHIFT LEVER CLIP BRACKET ROD INDICATOR CONTROL BAR CLUTCH CABLE CONTROL BAR Fig. 7 BRACKET REMOVE TILLER FROM CRATE • Make sure shift lever indicator is in “N” position (See END OF CLUTCH Fig. 7) CABLE • Tilt
Inhaltszusammenfassung zur Seite Nr. 7
OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. RUN STOP FAST SLOW CHOKE FUEL OIL CAUTION ENGINE ENGINE OR WARNING ON OFF TILLING TILLING FORWARD NEUTRAL REVERSE TH
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. 00155 TINE OPERATION - WITH WHEEL DRIVE HOW TO USE YOUR TILLER Always release drive control bar before moving shift lever Know how to operate all controls before adding fuel and into anoth
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION • Hold the drive control bar against the handle to start TILLING (See Fig. 12) tilling movement. Tines and wheels will both turn. • Release depth stake pin. Pull the depth stake up for • Move throttle control "FAST" position for deep tilling. increased tilling depth. Place depth stake pin in hole To cultivate, throttle control can be set at any desired of depth stake to lock in position. speed, depending on how fast or slow you wish to • Place shift lever indicator in counter r
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION TO START ENGINE (See Fig. 14) Oil Filler Plug CAUTION: KEEP TINE CONTROL IN “OFF” Oil Level PO SI TION WHEN STARTING ENGINE. When starting engine for the first time or if engine has run out of fuel, it will take ex tra pulls of the recoil starter to move fuel from the tank to the engine. 1. Make sure spark plug wire is prop er ly connected. 2. Place the fuel valve to the "ON" position. 3. To start a cold engine, move the choke lever to the "ON" position. Max Upper Level 4. Mo
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION CULTIVATING TILLING HINTS Cultivating is destroying the weeds between rows to pre- CAUTION: Until you are accustomed to vent them from robbing nourishment and moisture from the handling your tiller, start actual field use plants. At the same time, breaking up the upper layer of with throttle in slow position (mid-way soil crust will help retain moisture in the soil. Best digging between “FAST” and “IDLE”). depth is 1" to 3" (2.5-7.5 cm). Lower the outer side shields to protect
Inhaltszusammenfassung zur Seite Nr. 12
MAINTENANCE GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. T o receive full value from the warranty, the operator must main tain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. ENGINE All adjustments in the Service and Adjustments section RH GEAR CASE of this manual should
Inhaltszusammenfassung zur Seite Nr. 13
MAINTENANCE Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot muffler or cylinder fins as contact may cause burns. ENGINE OIL DRAIN LUBRICATION PLUG Use only high quality detergent oil rated with API s
Inhaltszusammenfassung zur Seite Nr. 14
MAINTENANCE COOLING SYSTEM (See Fig. 20) SPARK PLUG Your engine is air cooled. For proper en gine performance Replace spark plugs at the beginning of each tilling sea- and long life keep your engine clean. son or after every 25 hours of use, whichever comes first. • Clean air screen frequently using a stiff-bristled brush. Spark plug type and gap setting are shown in “PROD UCT SPEC I FI CA TIONS” on page 3 of this manual. • Remove blower housing and clean as nec es sary. • Keep cylinder fin
Inhaltszusammenfassung zur Seite Nr. 15
SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO REMOVE WHEEL (See Fig. 22) • Place blocks under trans mis sion to keep tiller from TO ADJUST HANDLE HEIGHT (See Fig. 21) tipping. Select handle height best suited for your tilling conditions. • Remove hairpin clip and clevis pin from wheel. Handle height will be different when tiller digs into soil. • Remove wheel and tire. • First loosen handle
Inhaltszusammenfassung zur Seite Nr. 16
SERVICE AND ADJUSTMENTS TO REPL ACE GROUND DRIVE BELT GROUND DRIVE BEL T ADJUSTMENT (See Figs. 23 and 24) (See Fig. 24) • Remove belt guard as described in “TO REMOVE BELT For proper belt tension, the extension spring should have GUARD”. about 5/8 inch (16 mm) stretch when drive control bar is • Remove old belt by slipping off engine pulley first then in “EN GAGED” position. This tension can be attained as remove from transmission pulley. fol lows: • Place new belt in groove o
Inhaltszusammenfassung zur Seite Nr. 17
SERVICE AND ADJUSTMENTS • To maintain the superb tilling performance of this ma- TINE REPLACEMENT chine the tines should be checked for sharpness, wear, (See Figs. 25, 26, and 27) and bending, particularly the tines which are next to the transmission. If the gap between the tines ex ceeds CAUTION: Tines are sharp. Wear 3-1/2 inches they should be replaced or straight ened gloves or other protection when han- as necessary. dling tines. • For tines that are slightly worn, the bolt ed t
Inhaltszusammenfassung zur Seite Nr. 18
STORAGE Immediately prepare your tiller for storage at the end of the ENGINE OIL season or if the unit will not be used for 30 days or more. Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CAUTION: Never store the tiller with gasoline in the tank inside a build ing where fumes may reach an open flame CYLINDER(S) or spark. Allow the engine to cool before storing in any enclosure. • Remove spark plug. • Pour 1 ounce (29 m
Inhaltszusammenfassung zur Seite Nr. 19
TROUBLESHOOTING POINTS 1 Out of fuel. 1 Fill fuel tank. Will not start 2 Fuel valve “OFF” 2 Turn fuel valve to the “ON” position. 3 Engine Switch “OFF” 3 Turn engine switch to the “ON” position. 4 Engine not “CHOKED” properly. 4 See “TO START ENGINE” in Operation section. 5 Engine flooded. 5 Wait several minutes before attempting to start. 6 Bad spark plug or improper gap. 6 Replace spark plug or adjust gap. 7 Dirty air filter. 7 Clean/replace air filter. 8 Water in fuel. 8 Empty fuel tank and c
Inhaltszusammenfassung zur Seite Nr. 20
REPAIR PARTS TILLER - - MODEL NUMBER DRT 900 (96093000801), PRODUCT NUMBER 960 93 00-08 HANDLE ASSEMBLY 8 6 2 30 10 13 33 12 2 14 11 41 15 27 27 29 37 21 16 37 18 4 20 19 26 24 11 17 23 31 Handle_assy_99_23 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 21 532 18 11-27 Handle 2 532 42 76-43 Grip, Handle 4 532 15 92-28 Bar Assembly, Control 23 532 08 67-77 Screw, Hex Washer SLT #10-24 x .50 24 532 00 94-84 Clip 6 532 18 06-85 Panel, Control 8 871 19 10-08 Screw, Truss Hd. #10-24 un
