Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Please take a moment to review your safety labels. 1 Safety Labels WARNING This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING Your Responsibility Restrict the use of this p
Inhaltszusammenfassung zur Seite Nr. 4
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm. DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects
Inhaltszusammenfassung zur Seite Nr. 5
up and thrown by theblade. Thrown objects sightto cutting bladeis blocked by guards. can cause seriouspersonal injury. 24. Alwaysstop enginewhen edging or 6. Alwayswear safetyglasses or safety goggles trimming isdelayed or when transporting during operation andwhile per forming machine fromone location to another . an adjustment or repair to protectyour Never leave arunning machine unattended. eyes. Thrown objects whichricoch
Inhaltszusammenfassung zur Seite Nr. 6
Inhaltszusammenfassung zur Seite Nr. 7
Inhaltszusammenfassung zur Seite Nr. 8
Inhaltszusammenfassung zur Seite Nr. 9
Inhaltszusammenfassung zur Seite Nr. 10
Inhaltszusammenfassung zur Seite Nr. 11
Inhaltszusammenfassung zur Seite Nr. 12
Off-Season Storage Notes Observe the following when preparing the edger for long-term storage: 1. Clean and lubricate unit thoroughly as instructed 7 maintenance section of this manual. 2. Refer to the Engine Manual packed separately Off-Season with the edger for engine manufacturers’s storage instructions. 3. Coat the edger blade with chassis grease to prevent Storage rusting and corrosion. 4. Store the edger in a dry, clean area. Do not store next to any corrosive materials, such as law
Inhaltszusammenfassung zur Seite Nr. 13
Troubleshooting Guide 8 Problem Possible Cause(s) Corrective Action Troubleshooting Dirty air cleaner Refer to the Engine Manual packed with your unit. Engine fails to start Guide Engine needs to be primed Push primer bulb two or three times. Fuel tank empty Fill tank with clean, fresh gasoline. Stale fuel in gasoline tank Drain gasoline and refill tank with clean, fresh gasoline. Spark plug wire disconnected. Connect the spark plug wire to the spark plug. Spark plug fouled Clean, adjust gap o
Inhaltszusammenfassung zur Seite Nr. 14
Inhaltszusammenfassung zur Seite Nr. 15
9 Ref. Part No. Description Ref. Part No. Description 1 687-02022 Curb Height Adjustment Lever 32 732-04169 Compression Spring Part List: 2 687-02125A Curb Height Adjuster Plate 33 734-1988 Wheel 7 x 1.8 Spoke Bar Grey † Handle/Frame/ 3 687-02126 Blade Plate Assembly 34 734-1987 Wheel 8 x 1.8 Spoke Bar Grey † Wheel Assembly 4 710-0191 Screw 3/8-24 35 736-0234 Flat Washer, .385 x 1.5 x .075 5 710-0411 Screw 3/8-16 36 736-04088 Flat Washer .635x1.24x.181 Model 550 Series 6 710-04389 Hex Screw, 5
Inhaltszusammenfassung zur Seite Nr. 16
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with respect e. MTD does not extend any warranty for products sold or exported to new merchandise purchased and used in the United States, its outside of the United States, its possessions and territories, except possessions and territories. those sold through MTD’s authorized channels of export distribution. “MTD” warrants this product against defects in material and workman- f. Replacement parts tha
