Inhaltszusammenfassung zur Seite Nr. 1
M1108D
ITEM NUMBER: 1108, 1109, 1114
TM
SERIAL NUMBER: _____________________
Owner’s Manual
Instructions for Assembly, Testing, Operation, Servicing,
& Storage
22, 30, 37-Ton Log Splitters: Outdoor hydraulic powered
machine that splits wood logs.
WARNING
READ and UNDERSTAND this manual completely before using log splitter.
All operators of this equipment must read and completely understand all safety information, operating instructions,
maintenance and stor
Inhaltszusammenfassung zur Seite Nr. 2
Hazard Signal Word Definitions 2
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents About Your Log Splitter 4 Safety Label Locations 5 Machine Components Identification 7 Initial Set-up 8 Optional 4-Way Wedge Wings 10 Moving & Towing to the Job Site 11 Before Each Use: Step One: Inspection/Maintenance 14 Step Two: Refueling 17 Step Three: Work site Selection & Set-up 18 Splitting Operation 20 Storage 26 Perio
Inhaltszusammenfassung zur Seite Nr. 4
About Your Log Splitter Thank you for purchasing your Northstar log splitter! About Your Log Splitter: This log splitter is a machine designed to split wood logs using a hydraulically powered moving wedge. The log splitter’s gasoline engine is used to pressurize the hydraulic system. This log splitter is designed to split logs lengthwise with the grain only. Your splitter can be used in either a vertical or horizontal splitting position: • When the splitter is set up to oper
Inhaltszusammenfassung zur Seite Nr. 5
Safety Label Locations 11 9 4 5 8 7 2 10 6 6 3 Fig 02403 1 Reference Part Number Description number 1 39259 Warning Decal 2 777887 Splitter Operating Instruction Decal 3 777890 Fire Hazard Warning Decal 4 777891 Hydraulic Fluid Warning Decal 5 777892 Moving/Towing Decal 6 778593 Outrigger Leg Decal 7 778597 Horizontal Lock Decal 8 778609 Control Decal 9 778610 Log Splitter Warning Decal 10 778714 Vertical Lock Deca
Inhaltszusammenfassung zur Seite Nr. 6
Safety Label Locations WARNING POISONOUS GAS This product's use gives off carbon monoxide, an odorless gas that can kill you. ONLY use outdoors and away from air intakes. NEVER use inside homes, garages, or sheds. EVEN IF you run a fan or open doors and windows. See product manual for more details. ©2005 Northern Tool + Equipment Co. 1-800-270-0810 PN 39259 WARNING ESCAPING HIGH PRESSURE HYDRAULIC FLUID HAZARD High fluid pressures and temperatures are developed in the
Inhaltszusammenfassung zur Seite Nr. 7
Machine Component Identification 11 10 9 8 13 4 20 18 6 7 1 5 3 2 14 15 21 19 Fig 02407 12 17 Ref Description Ref Description 1 2” Ball Coupler 11 Endplate 2 Horizontal Lock 12 Outrigger Legs 3 Lifting Handle 13 Engine 4 Cylinder 14 Hydraulic Tank 5 Hydraulic Oil Dipstick 15 Suction Strainer 6 Split Control Lever 17 Safety Chains 7 Control Valve 18 Vertical Lock 8 Wedge 19 Hydraulic Oil Filter 9 Log Cradle 20 Grease Zerks 10 Beam 21 Drain Plug 7
Inhaltszusammenfassung zur Seite Nr. 8
Initial Set-Up IMPORTANT! Engine is shipped without oil. DO NOT start the engine before adding oil. See Assembly Instructions section of this manual to assemble the log splitter before set-up. Closely inspect all log splitter components. Step One: (See Machine Components section of this manual for diagram of components.) Inspect Log Splitter • If you have missing components, contact Customer Service at 1-800-270-0810. Components. • If you have damaged components, contact th
Inhaltszusammenfassung zur Seite Nr. 9
Initial Set-Up Step Four: Pump grease into grease zerks found under each keeper. This will help prevent wear between the keepers and beam. Lubricate Keepers BEAM WEDGE KEEPER GREASE ZERK Fig 02408 9
Inhaltszusammenfassung zur Seite Nr. 10
Optional 4-Way Wedge Wings Wing Assembly 4-Way Wedge Wings 1. Unbox and identify components 2. Insert Nylon nuts into hex cutouts in wing 3. Position wings into proper locations on the wedge and bolt into position using supplied bolts ” 4. Tighten the bolts with a 3/8 hex wrench Exploded View Assembled View • 4-Way Wings create additional pinch points when the wedge is moving forward or backwards. Keep hands clear of the wedge, wedge wings, and the log while the wedg
Inhaltszusammenfassung zur Seite Nr. 11
Moving and Towing to the Job Site WARNING The log splitter is heavy. It can crush and cause serious injury if it rolls out of control or tips over. Follow the instructions below for safely moving and towing the log splitter. Moving the log splitter: 1. Place in Make sure the log splitter is locked in the horizontal position with hitch pin Horizontal before moving. position NEVER move log splitter when it is in vertical configuration because it will be unstable and could t
Inhaltszusammenfassung zur Seite Nr. 12
Moving and Towing to the Job Site Towing: 1. Read instructions Review towing safety instructions in your vehicle manual. 2. Check tires Make sure tires are fully inflated and in good repair. WARNING: • Do not over-inflate tires. Serious injury can occur if tire explodes. • When seating a bead after repair, do not exceed 30 PSI. Pressures higher than 30 PSI can cause the tire and wheel to rupture and explode. 3. Attach to hitch Attach log splitter to vehicle hitch (2” ball) 1. Att
Inhaltszusammenfassung zur Seite Nr. 13
Moving and Towing to the Job Site Fig 02410 Attach coupler to class 2 or higher hitch with 2” ball. Latch Securely. Lock front outrigger leg in the Lock rear Hook both safety up position outrigger leg in the chains to the towing up position vehicle Tow log splitter carefully to desired work site. 6. Tow to desired (See Before Each Use section on selecting an appropriate work site) location Important safety instructions: • Added length. Be aware of the a
Inhaltszusammenfassung zur Seite Nr. 14
Before Each Use-Inspection / Maintenance Step One: Inspect and maintain log splitter before each use If the log splitter has been used previously, it must be inspected and maintained BEFORE EACH SUBSEQUENT USE. WARNING ALWAYS shut off the engine, disconnect the spark plug, and relieve system pressure before inspecting, cleaning, adjusting, or repairing the splitter. Relieve system pressure by moving Split Control Lever back and forth several times. IMPORTANT: If a part need
Inhaltszusammenfassung zur Seite Nr. 15
Before Each Use-Inspection / Maintenance 5. Hydraulic system Check the hydraulic system carefully: 1. Visually inspect all hoses, tubing, clamps/fittings, pump, and cylinder for cracks, fraying, kinks, or other damage. 2. Check all components for oily residue, which may indicate a leak. Do NOT operate the log splitter if there is any indication of damage or oily residue. Small leaks in hydraulic lines can cause severe injuries and can also be an indication of catastrophic failure in t
Inhaltszusammenfassung zur Seite Nr. 16
Before Each Use-Inspection / Maintenance 9. Tires Make sure tires are fully inflated and in good repair if you will be towing the splitter. See tire sidewall for recommended tire pressure. WARNING: • Do not over-inflate tires. Serious injury can occur if tire explodes. • When seating a bead after repair, do not exceed 30 PSI. Pressures higher than 30 PSI can cause the tire and wheel to rupture and explode. 10. Shields / guards Replace all guards and shields after servicing the log
Inhaltszusammenfassung zur Seite Nr. 17
Before Each Use - Fueling Step Two: Fueling WARNING Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Use extreme care when handling gasoline. The engine must be off and allowed to cool at least two minutes before adding fuel. 1. Engine off / cool WARNING: A running engine is hot enough to ignite fuel. Never add fuel or remove gas cap if engine is running or still hot. 2. Outdoor location Fill fuel tank outdoors
Inhaltszusammenfassung zur Seite Nr. 18
Before Each Use – Work Site Selection & Set-Up Step Three: Work site selection and log splitter set-up WARNING It is important to select an appropriate work site and properly set up the log splitter in order to minimize the risk of slips and falls, equipment rolling or tipping over, carbon monoxide poisoning, and accidental fires. 1. Select location Select an appropriate location for operating the log splitter. Requirements: 1. Dry-level surface with good footing. Stay clea
Inhaltszusammenfassung zur Seite Nr. 19
Before Each Use – Work Site Selection & Set-Up Lock both the outrigger legs in the “DOWN” position. 4. Lock both outrigger legs DOWN Lock rear Lock front outrigger leg in outrigger leg in the down the down position position Block the wheels to prevent unintended movement of the log splitter. 5. Block wheels Apply grease into grease zerks located under both keepers. 6. Apply grease 19
Inhaltszusammenfassung zur Seite Nr. 20
Splitting Operation WARNING Before starting this log splitter, review the following instructions and safety information for safe operation of the log splitter. Failure to follow these rules may result in serious injury to the operator or bystanders from moving parts that crush, cut, or entangle from flying objects, burns, fire, falling or tripping, or from carbon monoxide poisoning. General safety information: • Read manual. Do not allow anyone to operate the log splitter who has no
