Inhaltszusammenfassung zur Seite Nr. 1
Triple Bag Catcher
Kit No. 7600069 - 7600070
Safety Instructions
and Operator’s Manual
Instruction Manual No. 7102356 (Rev. C, 06/04/2008)
1
TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS WARNING All safety instructions and operating instructions in the manuals provided with the Snapper Lawn Tractor and this Grass Catcher attachment must be followed. Read, understand, and follow ALL instructions and warnings in the Operator’s Manual provided with the machine, with this attachment, and ALL instructions and warnings on the machine, engine and attachment. Failure to comply with ALL instructions and warnings can result in damage, serious injury
Inhaltszusammenfassung zur Seite Nr. 3
Installation Instructions Install Bagger Mount Install Grass Bag Support 1) Remove three bolts – two on the rear 1) Align the lower U-shaped channel on the of the tractor frame, and the top bolt on Grass Bag Support (7500994) with the U- the right rear of the tractor frame. See shaped slot in the top of the Bagger Mount. Figure 1. The two rear bolts will be Insert the channel support fully into the replaced with longer bolts supplied in bagger mount. See Figure 2. the kit. Save the rig
Inhaltszusammenfassung zur Seite Nr. 4
Install Grass Bags Install Grass Bag Adapter 1) Align the slot on the hanger of the 1) 46” & 52” Models Only – Attach the Grass Bag Assembly (7500995) with Latch Pin (M720543) to the appropriate the tab on the grass bag support. Grass Bag Adapter, using one carriage 2) Insert the tab into the slot. Repeat bolt 1/4-20x5/8 (1960252) and one for all three grass bags. See Figure 4. center lock flange nut 1/4-20 (1930642). See Figure 6 (inset). 2) The Grass Bag Adapter attaches to the dec
Inhaltszusammenfassung zur Seite Nr. 5
Install Upper Elbow Tube and Middle Install Baffles on 52” Deck (Not Grass Tube required on other size decks) 1) Slide the upper elbow tube 1) Position the left deck baffle (1733885) into the cover, aligning the (7400267A) and right deck baffle ridges with the notches in the cover (7400268A) on the front inside surface opening. The opening of the elbow tube of the 52” deck. Align the holes and must face towards the center of the insert carriage bolts (M720053) with the catcher. See Figur
Inhaltszusammenfassung zur Seite Nr. 6
Operation and Maintenance Instructions INTRODUCTION: EMPTYING GRASS CATCHER Follow operation and maintenance 1) Empty Grass Catcher often to avoid instructions in the Operator’s Manual overfilling. Overfilling the grass bags provided with the Snapper Lawn reduces performance and causes Tractor. clogging of tube, adapter and deck. GRASS CATCHER OPERATION 2) Turn blades off. Drive machine to 1) Select desired cutting height. Choose location the clippings are to be dumped. a setting
Inhaltszusammenfassung zur Seite Nr. 7
IF THE GRASS CATCHER BECOMES GRASS CATCHER MAINTENANCE CLOGGED Grass Catcher components are subject to The grass catcher may become plugged wear and deterioration during normal if the conditions are too severe, the usage. Inspect all components frequently catcher is overfilled, or the machine is for signs of wear and deterioration. used improperly. If plugging does occur, Replace worn or damaged components attempt the following: immediately. BEFORE EACH USE WARNING 1) Inspect all Ca
Inhaltszusammenfassung zur Seite Nr. 8
Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 8 TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 9
Parts Manual Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 9 TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 10
Bagger Mount Tractor Frame Existing 1 Hardware 2 Grass Bag Support 3 4 1 2 Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 10 TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 11
BAGGER MOUNT 1 7400272A WELDMENT, MOUNT, GRASS CATCHER 1 2 1930595 BOLT – WHIZ LOCK 5/16-18 X 1-1/4 2 -- 1927557 NUT – HEX FLANGE 5/16-18 WHIZ LOCK 2 -- 7091323 HEX FLANGE BOLT, 1/2-13 X 1-1/4 1 -- 7091544 HEX FLANGE NUT, 1/2-13 1 GRASS BAG SUPPORT 1 7500994 ASSEMBLY, GRASS CATCHER SUPPORT 1 2 7091323 HEX FLANGE BOLT, 1/2-13 X 1-1/4 2 -- 7091544 HEX FLANGE NUT, 1/2-13 2 3 7300957A ARM, SUPPORT, TRIPLE GRASS CATCHER 1 4 M720527 PIN, CHANNEL MTG, GRASS
Inhaltszusammenfassung zur Seite Nr. 12
Grass Bag Assembly 2 3 1 Cover Assembly 1 3 2 4 Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 12 TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 13
GRASS BAG ASSEMBLY 1 1733695 BAG, GRASS CATCHER, CLOTH 3 2 1733517 HOOP - BAG TRIPLE 3 -- 1733709 TUBE, CLIP, GRASS BAG 3 3 1703807A HANGER, GRASS BAG 3 -- 1672023A CLAMP, GRASS BAG 3 -- 1931333 CARRIAGE BOLT, 5/16-18 X 3/4 6 -- 1917356 LOCKWASHER, SPRING 5/16 6 -- 1917372 NUT - HEX 5/16-18 NC-2B 6 COVER ASSEMBLY 1 7500996 ASSEMBLY, COVER AND HANDLE, GRASS CATCHER 1 -- 1733546 COVER ASSY - TRIPLE 1 -- M720537 HANDLE, COVER 1
Inhaltszusammenfassung zur Seite Nr. 14
Grass Bag Adapter 2 3 4 6 5 1 6 Grass Tube Assembly 1 2 Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 14 TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 15
GRASS BAG ADAPTER 1 M720551 42" BAGGER BOOT 1 1 M720560 46" BAGGER BOOT 1 1 7102377 52" BAGGER BOOT 1 2 M720543 PIN, LATCH 1 3 1960252 CARRIAGE BOLT, 1/4-20 X 5/8 1 4 1930642 NUT – CENTER LOCK FLANGE 1/4-20 1 5 1960223 CARRIAGE BOLT 2 -- 7011791 BOLT RETAINER, 5/16- BLACK 2 6 M720125 NUT, 5/16-18 WINGNUT 2 GRASS TUBE ASSEMBLY – 42” 1 1733885 ELBOW - UPPER TUBE 1 2 7500993 ASSEMBLY, TUBE, CENTRAL 1 -- 1734299 TUBE, GRASS
Inhaltszusammenfassung zur Seite Nr. 16
Baffle Assembly 4 2 4 1 3 Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 16 TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 17
BAFFLE ASSEMBLY 1 7400268A BAFFLE, RIGHT 1 2 7400267A BAFFLE, LEFT 1 3 M720053 CARRIAGE BOLT 2 1 7090585 HEX FLANGE NUT, 5/16-18 5 Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 17 TP 200-5352-C-AT-N
Inhaltszusammenfassung zur Seite Nr. 18
Instruction Manual No. 7102356 (Rev. C, 06/04/2008) 18 TP 200-5352-C-AT-N
