Inhaltszusammenfassung zur Seite Nr. 1
®
USER GUIDE
Aleratec 1:15 Blu-ray/DVD/CD
Tower Publisher SLS™
Part No. 260203
Inhaltszusammenfassung zur Seite Nr. 2
Copyright/Model Identification The content of this manual is for informational purposes only and is subject to change without notice. This manual is copyright with all rights reserved. Under copyright laws, this manual and the software described within may not be copied, except in the normal use of the product(s) described within or to make a backup copy. Copyright© 2011 Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.S.A. ® Aleratec is a registered trademark, and 1:15 Blu-ra
Inhaltszusammenfassung zur Seite Nr. 3
Radio/TV Interference Statement The equipment described in this guide emits radio frequency energy. If it is not installed in accordance with the manufacturer’s instructions, it may cause interference with radio or television reception. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
Inhaltszusammenfassung zur Seite Nr. 4
Safety Regulations WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to authorized personnel only. CAUTION As the laser beam in these 1:15 Blu-ray/DVD/CD Tower Publisher SLS is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to authorized personnel only. The use of optical instruments with this product will increase eye hazard. This BD/DVD/CD Duplicator is
Inhaltszusammenfassung zur Seite Nr. 5
Table of Contents Introduction ...................................................................................................1 Product Features ...................................................................................................1 Key Items – 1:15 Blu-ray/DVD/CD Tower Publisher SLS .................................2 1:15 Blu-ray/DVD/CD Tower Publisher SLS: LCD Front Panel ........................3 1:15 Blu-ray/DVD/CD Tower Publisher SLS: Removable Hard Disk Drive ......4 Preca
Inhaltszusammenfassung zur Seite Nr. 6
® www.aleratec.com
Inhaltszusammenfassung zur Seite Nr. 7
Introduction Thank you for purchasing the 1:15 Blu-ray/DVD/CD Tower Publisher SLS. Please read this User Guide thoroughly before using this product. Product Features The Aleratec 1:15 Blu-ray/DVD/CD Tower Publisher SLS is a stand alone LightScribe disc publishing system with the capability of simultaneously producing up to 15 BD/DVD/CD copies or clearly labeled discs, and no computer is required. • Removable Hard Disk Drive to store disc images and label files.* • Aleratec only USB fast key i
Inhaltszusammenfassung zur Seite Nr. 8
Introduction Key Items – 1:15 Blu-ray/DVD/CD Tower Publisher SLS Removable Control Panel Hard Disk Drive (see page 4) BD/DVD/CD Source Drive BD/DVD/CD RW LightScribe Drives* *Note: There is currently no LightScribe Blu-ray media available. 2 www.aleratec.com
Inhaltszusammenfassung zur Seite Nr. 9
Introduction 1:15 Blu-ray/DVD/CD Tower Publisher SLS: LCD Front Panel (View may vary from picture) 1 2 3 Initialize Duplicator ESC ENT 1-3 ver: X.XX COPY USB PRINT SOURCE 4 5 6 7 8 9 1. Display shows all functions and messages 2. ESC button is used to cancel a selected function 3. ENT button is used to execute a selected function 4. COPY button will start the “Autocopy” menu function. (See page 59 for more information) 5. USB button will take you directly to the USB On/Off mode option. (See
Inhaltszusammenfassung zur Seite Nr. 10
Introduction 1:15 Blu-ray/DVD/CD Tower Publisher SLS: Removable Hard Disk Drive Carriage Lever Removable Hard Disk Drive Key in Lock Your Tower Publisher SLS is equipped with a removable hard disk drive (HDD) for storing images of frequently copied discs. Storing an image of a disc you want to copy on an HDD improves duplication speed, and adds the convenience of not having to look around for the actual source disc you want to copy. Your removable HDD provides extra security, in that you c
Inhaltszusammenfassung zur Seite Nr. 11
Precautions Before you start: Before you start using your 1:15 Blu-ray/DVD/CD Tower Publisher SLS, please read the following to ensure proper operation. Good care will help assure maximum product life. Improper operating environment and misuse may void the warranty. Choose a Good Location: 1. Allow adequate clearance for moving parts. 2. Do not place near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, mechanical vibration or shock. 3. If the duplicator
Inhaltszusammenfassung zur Seite Nr. 12
Precautions Before you start - continued External Connection Warning: In order to operate the duplicator solely as a standalone unit (no connection to the computer), you have to make sure all of the USB connection(s) are off. If by any chance, the USB connection(s) are on, please refer to “Setup Guide: Setup USB 2.0 device(s)” Maintenance: It is very important to operate and keep the duplicator in a dust free, clean environment since dust is the number 1 killer for BD/DVD/CD recording devic
Inhaltszusammenfassung zur Seite Nr. 13
Overview Unpacking the Unit Your system was shipped in one box and contains the 1:15 Blu-ray/DVD/CD Tower Publisher SLS and cables. Carefully open the box and remove the top protective foam padding. Remove the following: • 1:15 Blu-ray/DVD/CD Tower Publisher SLS • 2 Power Cords • 1 USB 2.0 Cable • 1 Quick Start Guide • 1 Installation CD Note: It is important to keep the original shipping container and packaging. In the event you misplace your packaging and need to ship the 1:15 Blu-ray/ DVD
Inhaltszusammenfassung zur Seite Nr. 14
Overview LightScribe Software Installation Minimum System Requirements: PC running Windows 2000, XP, Vista or 7 1. Install the Aleratec File System Manager. First write down the key code labeled “Product Key” on the front of the disc and then put the disc into your PC. If Autorun does not begin, go to “My Computer” and explore the CD and double-click “Setup” to begin the installer manually. Follow the prompts and insert the key code that you wrote down where “Serial Number” is displayed
Inhaltszusammenfassung zur Seite Nr. 15
Overview c. Click Install to complete the installation. 3. Connect the 1:15 to your PC with the USB cable. 4. Make sure the 1:15 is in USB mode. Press the “USB” fastkey on the control panel on the front of the 1:15. If the screensaver is on you may have to press the button twice. 5. You will see the LCD screen display the “USB Connection” menu. Below this title you will see an “On” or “Off” listed. This is the current status of the USB connection. To change the current status, use either
Inhaltszusammenfassung zur Seite Nr. 16
Overview 6. After the 1:15 Tower Publisher SLS has rebooted, go to “My Computer” in Windows and look to see if the HDD is there. It will be labeled as “Duplicator”. 7. If you open the drive location you will see three or four folders. a. The “dup” folder is where “.iso” files, “.nrg” files and folders of data can be put in for disc burning.* b. The “label” folder is where “.lsi” files created by the LightScribe Template Labeler program will be placed. * Duplicating from folders on the Dupl
Inhaltszusammenfassung zur Seite Nr. 17
Overview Using the LightScribe Labeling Software The following procedure demonstrates using the LightScribe Template Labeler to generate the label files (.lsi) used by the Stand-Alone Tower Publisher SLS. 1. Launch the LightScribe Template Labeler. ▪ Click the shortcut on your desktop, or go to: Start → All Programs→ LightScribe Direct Disc Labeling → LightScribe Template Labeler. Note: Ignore the “LightScribe Disc Insertion” shown below by pressing the OK button. 2. Select a Template. You
Inhaltszusammenfassung zur Seite Nr. 18
Overview 3. Insert Text and/or Pictures into the template. Depending on the template chosen, you may have options to modify text box(es) or picture(s). ▪ To insert pictures, click on the dedicated area to select the picture you’d like to use. ▪ To insert text, click on the text field, and type the text you’d like use. Note: Depending on the template chosen, you may enter multiple lines of text. 4. When you are satisfied with your disc design, click “Preview and Print”. ▪ Select the “Best” c
Inhaltszusammenfassung zur Seite Nr. 19
Overview Using the LightScribe Labeling Software - continued A menu will appear prompting you to save your file. Navigate to the “label” folder located on the “Duplicator” drive. You may copy multiple files into this folder. Note: The 1:15 Tower Publisher SLS will only recognize label files located in the main LABEL folder. Any file that is placed outside of the main LABEL folder or in a subfolder will not be recognized as a label. Create a name for the file and click the “Save” button. 5.
Inhaltszusammenfassung zur Seite Nr. 20
Overview 6. Press the “USB” button on the duplicator and set the USB mode to “Off”. Reboot the duplicator by turning it off and then on again. After the device has completed the start up process, press the “Print” fast key (also menu option 2) on the main menu of the duplicator and push the ENT key. 7. The “Please Select Label” menu will appear. The newly created label file will appear below this prompt within the “label” folder. If there are multiple files, use the UP and DOWN arrow keys
