Inhaltszusammenfassung zur Seite Nr. 1
™
Netra ft 1800
Installation Guide
Sun Microsystems, Inc.
901 San Antonio Road
Palo Alto, CA 94303-4900 USA
650 960-1300 Fax 650 969-9131
Part No.: 805-4533-10
Revision A, February 1999
Send comments about this document to: docfeedback@sun.com
Inhaltszusammenfassung zur Seite Nr. 2
Copyright 1999 Sun Microsystems, Inc., 901 San Antonio Road • Palo Alto, CA 94303 USA. All rights reserved. This product or document is protected by copyright and distributed under licenses restricting its use, copying, distribution, and decompilation. No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors, if any. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers. P
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1. Before Installation 1 Electrical Supply Considerations 1 Environmental Considerations 1 Dimensions 2 Airflow Consideration when Mounting in the Equipment Frame 2 Mechanical Considerations when Mounting in the Equipment Frame 6 Mounting Requirements 6 2. Hardware Installation 9 Unshipping and Mounting the System 9 Mounting Flanges 13 19-inch Mountings 13 23-inch, 24-inch and 600mm Mountings 18 Cable Bracket Assemblies 22 Removing and Installing Modules 23 Module Injector/Ejector Mecha
Inhaltszusammenfassung zur Seite Nr. 4
Installing the Filter Trays 36 CAF External I/O Connections 38 System Console Terminal Connections 39 Modem Port Connections 40 Alarms Port Connections 41 3. Electrical Supply Installation 43 System Switch 43 DC Source Site Requirements 44 Overcurrent Protection Requirements 44 Required Connection Materials 48 DC Supply and Ground Conductor 48 Dual Grounding Environment 49 Connecting the Power Leads 51 4. Powering on the System 55 5. Software and Operating Environment Installation 57 Netra ft 18
Inhaltszusammenfassung zur Seite Nr. 5
6. Installing and Configuring Sun StorEdge Volume Manager 65 Before You Install Sun StorEdge Volume Manager 65 Installing the Volume Manager Software 67 Mounting the CD-ROM Manually 67 Running the Installation 67 Setting up the Volume Manager Environment 68 Initializing the Volume Manager 69 Setting up Boot Disks 70 Setting up Other Disks 71 Configuring Storage 71 Boot Disk Aliases 72 Index 73 Contents v
Inhaltszusammenfassung zur Seite Nr. 6
vi Netra ft 1800 Installation Guide • February 1999
Inhaltszusammenfassung zur Seite Nr. 7
Figures FIGURE 1-1 Netra ft 1800 Airflow Requirements (External) 4 FIGURE 1-2 Netra ft 1800 Airflow Requirements (Internal) 5 FIGURE 2-1 Shipping Brackets and Sacrificial Plinth 11 FIGURE 2-2 Location Matrix For Mounting Flange Screws (19-inch rack) 14 FIGURE 2-3 Support Rail and Fixings (19-inch Rack) 15 FIGURE 2-4 Orientation of Support Rail Spacers 16 FIGURE 2-5 Rear Rack Mounting (19-inch Rack) 16 FIGURE 2-6 19-inch Rack Mounting Flange Kit 17 FIGURE 2-7 23-inch Rack Mounting Flange Kit 19 F
Inhaltszusammenfassung zur Seite Nr. 8
FIGURE 2-18 Removing a DSK Module 34 FIGURE 2-19 Cable Management Shelf 35 FIGURE 2-20 Large Filter Tray 36 FIGURE 2-21 Small Filter Tray 37 FIGURE 2-22 External I/O Connections on CAF Module 38 FIGURE 3-1 Circuit Breakers for Single Power Rails 46 FIGURE 3-2 Circuit Breakers for Dual Power Rails 47 FIGURE 3-3 Location of Chassis-to-Logic-0V Link and Grounding Points, and Wrist Strap Connection Point 50 FIGURE 3-4 Power Inlet Filter 51 FIGURE 3-5 Power Connector Wiring Polarity and Securing Scre
Inhaltszusammenfassung zur Seite Nr. 9
Tables TABLE 1-1 Mounting Hole Pattern Dimensions 7 TABLE 2-1 19-inch Mounting Flange Kit 13 TABLE 2-2 Support Rail Screw Hole Locations 15 TABLE 2-3 23-inch, 24-inch and 600mm Mounting Flange Kits 18 TABLE 2-4 Console Connector Pinout 39 TABLE 2-5 Console and Modem Port Parameters 39 TABLE 2-6 Modem Port Pinout 40 TABLE 2-7 Alarms Port Pinout 41 TABLE 3-1 Overcurrent Protection Requirements 44 TABLE 5-1 Suggested Disk Layout 62 ix
Inhaltszusammenfassung zur Seite Nr. 10
x Netra ft 1800 Installation Guide • February 1999
Inhaltszusammenfassung zur Seite Nr. 11
Preface This document describes the installation procedures for the core hardware and software used in the Netra™ ft 1800. Upon completion of the procedures in this manual, the Netra ft 1800 is fully functional as a fault-tolerant Solaris™ server. Who Should Use This Book This guide is intended to be read by installation engineers, software support personnel and service personnel. It is not intended for the end user of the system. How This Book Is Organized This guide is arranged as follows: Cha
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 6 “Installing and Configuring Sun StorEdge Volume Manager” summarizes what you need to know in order to use the Volume Manager on the Netra ft 1800. Related Books ■ Netra ft 1800 Software Release Notes (Part No. 805-4527-10) ■ Netra ft 1800 Hardware Release Notes (Part No. 806-0179-10) ■ Netra ft 1800 CMS API Developer’s Guide (Part No. 805-5870-10) ■ Netra ft 1800 CMS Developer’s Guide (Part No. 805-7899-10) ■ Netra ft 1800 Developer’s Guide (Part No. 805-4530-10) ■ Netra ft 1800 Hardwa
Inhaltszusammenfassung zur Seite Nr. 13
Shell Prompts in Command Examples The following table shows the default Open Boot PROM (OBP) prompt and the system prompt and superuser prompt for the C shell, Bourne shell, and Korn shell. TABLE P-2 Shell prompts Shell Prompt Open Boot PROM prompt ok C shell prompt machine_name% C shell superuser prompt machine_name# Bourne shell and Korn shell prompt $ Bourne shell and Korn shell superuser prompt # Symbols The following symbols mean: Note – A note provides information which should be considere
Inhaltszusammenfassung zur Seite Nr. 14
Sun Documentation on the Web sm The docs.sun.com web site enables you to access Sun technical documentation on the Web. You can browse thedocs.sun.com archive or search for a specific book title or subject at: http://docs.sun.com Sun Welcomes Your Comments We are interested in improving our documentation and welcome your comments and suggestions. You can email your comments to us at: docfeedback@sun.com Please include the part number of your document in the subject line of your email. xiv Netra
Inhaltszusammenfassung zur Seite Nr. 15
CHAPTER 1 Before Installation This section provides information on what should be considered when choosing a location for a Netra ft 1800 system. Note – This equipment is only intended for installation in a Restricted Access Location as defined by UL1950, 3rd Edition, and EN60950: 1992 / A11: 1997. Electrical Supply Considerations Before you install the system, verify that the correct power supply is available. Refer to “DC Source Site Requirements” on page 44 for further information. Environmen
Inhaltszusammenfassung zur Seite Nr. 16
■ Relative humidity 1 ■ Operating: 5 to 85% noncondensing 1 ■ Storage: 10 to 90% noncondensing ■ Elevation ■ Operating: 0 to 3000 meters ■ Storage: 0 to 12000 meters Dimensions ■ Height: 1466.85 mm (57.75 inches) 33U NOM ■ Width: 437.60 mm (17.22 inches) ■ Depth: 392.8 mm (15.4 inches) ■ Weight: Maximum 190.5 kg (420 lb) (excluding rack or AC converter items) ■ Maximum rate of heat release for fully configured system: 3000W (10,200 Btu/hour) ■ GR 63 CORE heat release calculation result: 425.4 W
Inhaltszusammenfassung zur Seite Nr. 17
3. A minimum of 2U (88.9 mm/3.5 inches) clearance must be allowed at both top and bottom of the Netra ft 1800 cabinet when mounted to allow adequate inlet and exhaust ventilation. 4. The Netra ft 1800 system must not be mounted above any heat-generating sources within the same frame unless a heat deflector is used to provide fresh inlet air at ambient temperature. 5. To maintain adequate airflow, replace the environmental filters every six months (contact your local support organization for furt
Inhaltszusammenfassung zur Seite Nr. 18
Minimum 2U (90 mm) gap Minimum 2U (90 mm) gap FIGURE 1-1 Netra ft 1800 Airflow Requirements (External) 4 Netra ft 1800 Installation Guide • February 1999
Inhaltszusammenfassung zur Seite Nr. 19
Min. 2U (90 mm) gap at top of system CAF CAF PSU PSU CPU CPU PSU CPU PSU PSU PSU CAF CAF Front Rear Front Rear Front Min. 2U (90 mm) gap at base of system Fan unit Min. 75 mm between front of system and rack door (if fitted) FIGURE 1-2 Netra ft 1800 Airflow Requirements (Internal) Chapter 1 Before Installation 5
Inhaltszusammenfassung zur Seite Nr. 20
Mechanical Considerations when Mounting in the Equipment Frame Caution – Mechanical assistance is required if installing a loaded chassis. If you intend not to use a lifting device for installation, all modules other than the motherboards must be removed from the system prior to lifting. The empty chassis weighs approximately 49 kg (108 lb), or 68 kg (150 lb) with the motherboards, plus the adaptors. The weight of any removable module depends on its configuration. Weight warning labels are for g
