Inhaltszusammenfassung zur Seite Nr. 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Medalist SL Family
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
540sl, 851sl
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1080sl, 1270sl
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATA Interface Drives
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 2
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before you begin... . . . . . . . . . . . . . . . . . . . . . 3 Configuring the drive . . . . . . . . . . . . . . . . . . . . 5 Attaching the cables . . . . . . . . . . . . . . . . . . . . 8 Mounting the drive . . . . . . . . . . . . . . . . . . . . . 10 Transferring the software from the drive . . . . . . . . . 11
Inhaltszusammenfassung zur Seite Nr. 3
Medalist SL Family Installation Guide, November 1995 1 Introduction ® Thank you for choosing a Seagate drive. The purpose of this guide is to assist you with installing your new hard drive. Its organization outlines the complete installation process from han- dling the drive in “Before you begin...” to offering troubleshooting suggestions and technical support information. The topics dis- cussed are: • Handling your drive (see “Before you begin...” on page 3) • Configuring the drive • Attaching
Inhaltszusammenfassung zur Seite Nr. 4
2 Medalist SL Family Installation Guide, November 1995 Drive features Model ST5540A ST5851A ST51080A ST51270A Formatted Capacity 541 854.6 1,083 1,282 Mbytes Cylinders 1,050 1,656 2,100 2,485 Heads 16 16 16 16 Sectors 63 63 63 63 Average seek time 10.5 msec Cache (segmented) 128 Kbytes Spindle speed 5,376 RPM 1 External transfer rate 16.6 Mbytes per second max. Average sustained 1 3.5 Mbytes per second transfer rate LBA Supported Multiple block Supported read/write PIO modes 0, 1, 2, 3, 4 Multi
Inhaltszusammenfassung zur Seite Nr. 5
Medalist SL Family Installation Guide, November 1995 3 Before you begin... The drives in this manual are referred to by their model numbers: ST5540A for the Medalist 540sl, ST5851A for the Medalist 851sl, ST51080A for the Medalist 1080sl and ST51270A for the Medalist 1270sl. Application. Your Seagate drive is designed for IBM AT and compatible personal computers. It uses the ATA interface. It is intended for use with UL-listed computers or similar products. Drive handling. Your drive is vulnerab
Inhaltszusammenfassung zur Seite Nr. 6
4 Medalist SL Family Installation Guide, November 1995 Warranty. Your drive comes with a three-year limited warranty. Note. With regards to the EZ-Drive and SEG32BIT.386 software, there are no warranties, express or implied, including, but not implied, warranties of merchantability or fitness for a particular purpose. All such warranties are expressly and specifically disclaimed. Maintenance and repair. Seagate drives do not require mainte- nance. The head/disc assembly is sealed; a broken seal
Inhaltszusammenfassung zur Seite Nr. 7
Medalist SL Family Installation Guide, November 1995 5 Warning.Turn off the computer before you remove its cover. Turn off the power before you install or remove any adapter card or the drive. Caution. Special training or tools may be required to service laptop computers. Removing the cover may void your warranty. Review the terms and conditions of your warranty before removing the cover. Configuring the drive Required materials: • 2-mm jumper connector (supplied as spare jumpers) Your Seagate
Inhaltszusammenfassung zur Seite Nr. 8
6 Medalist SL Family Installation Guide, November 1995 Options jumper block pin 1 pin 1 Interface connector Standard power connector Circuit board +5V +5V return +12V return +12V Figure 1. Drive connectors One-drive only. Use this configuration if there are no other drives attached to the hard disc controller. Master with slave present. Use this configuration if the drive is the first of two drives in your system. The master drive is Drive 0 in the System Setup record. Slave. Use this confi
Inhaltszusammenfassung zur Seite Nr. 9
Medalist SL Family Installation Guide, November 1995 7 11 9 7 5 3 1 Circuit board 12 10 8 6 4 2 side up Spares One drive only Drive is master; slave is present Drive is slave when another drive is master Master/slave timing protocol. Drive waits up to 30 seconds for slave to respond. Cable select Remote LED connection pin 11 (–), pin 12 (+) Figure 2. Options jumper block settings
Inhaltszusammenfassung zur Seite Nr. 10
8 Medalist SL Family Installation Guide, November 1995 Master/slave timing protocol. This protocol involves the com- munication between the computer and the disc drives during the boot cycle only. The computer queries the master drive for the status of both drives. The slave must report its status to the master within a certain time period. If it does not respond, a timeout error is issued and the computer does not identify the slave. Place a jumper on pins 3 and 4 and on pins 5 and 6 to extend
Inhaltszusammenfassung zur Seite Nr. 11
Medalist SL Family Installation Guide, November 1995 9 Caution. The cable and connector bond is delicate. Pulling the cable to remove the connector may damage the cable. Attach an interface connector to the drive. If your interface con- nector has a key, it will plug into the drive only one way. Make sure that you do not bend the pins when you attach the cable. Attach an interface-connector to the hard-disc controller connec- tor on the motherboard or host adapter (see your system user’s guide o
Inhaltszusammenfassung zur Seite Nr. 12
10 Medalist SL Family Installation Guide, November 1995 Mounting the drive Required materials: • Four 6-32 UNC-2A screws (not included) The drive fits in a standard 3.5-inch bay and can be mounted in any orientation. Position the drive so that the cables are not strained or crimped. Secure it with four mounting screws not more than 6 full turns (0.20 inches) into the drive frame (see Figure 4). Caution. To prevent drive mounting-hole damage, use only the type of screws specified. This completes
Inhaltszusammenfassung zur Seite Nr. 13
Medalist SL Family Installation Guide, November 1995 11 Transferring the software from the drive Required materials: • Diskette Drive A • A bootable, blank, 1.2-Mbyte or larger diskette for Drive A • A bootable diskette with the Format command Recent developments in drive technology have pushed drive capacities beyond the limits that many older computers using DOS can address. Seagate provides software that allows these computers to surpass the address limit and access your new drive’s full capa
Inhaltszusammenfassung zur Seite Nr. 14
12 Medalist SL Family Installation Guide, November 1995 To transfer the software, you must put a blank, bootable diskette into Drive A. To create a bootable diskette: 1. Insert your DOS diskette into Drive A. 2. Type format a: /s. The drive reads the DOS diskette and prompts you to insert the diskette you want to format into Drive A. 3. Insert the blank diskette. Press ENTER. When the format is complete, you can transfer the installation software files to the diskette. To transfer the software f
Inhaltszusammenfassung zur Seite Nr. 15
Medalist SL Family Installation Guide, November 1995 13 the computer. The computer returns an invalid drive specifi- cation error if you try to access the drive. Caution. Do not write-protect the Seagate software diskette with EZ-Drive. The EZ-Drive program writes important in- formation back to the diskette during the installation. Configuring the computer Configuring the computer involves updating the computer’s Sys- tem Setup records with the new drive’s translation geometry (cylinder, head a
Inhaltszusammenfassung zur Seite Nr. 16
14 Medalist SL Family Installation Guide, November 1995 Determining whether your BIOS accepts more than 528 Mbytes The following suggestions can help you to determine whether your BIOS limits the drive capacity to 528 Mbytes. • If you are using a 286 or 386 computer, the native BIOS cannot recognize more than 528 Mbytes. • If the copyright date of the BIOS is earlier than 1994, the BIOS probably will not recognize more than 528 Mbytes. The BIOS copyright date, manufacturer and version number ap
Inhaltszusammenfassung zur Seite Nr. 17
Medalist SL Family Installation Guide, November 1995 15 Using the EZ-Drive installation software Note. The EZ-Drive software is authorized for installation only with the drive on which it is shipped. EZ-Drive allows your computer to access your Seagate drive’s full formatted capacity. It bypasses the BIOS during the boot sequence and uses information it creates on Drive C to identify the drive before DOS is loaded. During the installation, EZ-Drive: • Determines how many drives are installed •
Inhaltszusammenfassung zur Seite Nr. 18
16 Medalist SL Family Installation Guide, November 1995 Note. EZ-Drive is designed for DOS installations. It supports Microsoft MS-DOS Version 5.0 or later. EZ-Drive does not support: • Toshiba laptops, XT or Micro Channel computers • Non-ATA hard drives (SCSI, ESDI, MFM and RLL) • Some Local Bus adapters that use 32-bit mode • Some systems that have PIO mode 3 or 4 active • OS/2 and NT Caution. Some older virus-detection programs may misidentify the EZ-Drive information stored in conventional
Inhaltszusammenfassung zur Seite Nr. 19
Medalist SL Family Installation Guide, November 1995 17 4. Locate the bottom box on the screen. The model number of each drive EZ-Drive identifies is listed in this box. If a drive you have installed is not listed or the drive order (Drive 0 is the master, Drive 1 is the slave) is incorrect or there is a drive not identified message, make sure the master and slave jumpers are set correctly on the drives and the I/O and power cables are properly connected. Note. Other troubleshooting tips are ava
Inhaltszusammenfassung zur Seite Nr. 20
18 Medalist SL Family Installation Guide, November 1995 Booting with a diskette after EZ-Drive is installed When you boot with a diskette, you must allow the EZ-Drive information about the drive to load into memory before the system information on the diskette loads. The diskette accesses the BIOS directly, which does not recognize the EZ-Drive-installed drive. To boot your computer with a diskette: 1. Boot the computer with the diskette-drive door open. 2. Press the CTRL key when the followin
