Inhaltszusammenfassung zur Seite Nr. 1
BlueStorm Universal PCI
User Manual
Contact Information:
Connect Tech Inc.
42 Arrow Road
Guelph, Ontario, Canada N1K 1S6
Tel: 519-836-1291 (International)
800-426-8979 (Canada & USA)
Fax: 519-836-4878
Email: sales@connecttech.com
support@connecttech.com
URL: www.connecttech.com
CTIM-00015 revision 8 November, 2007
Inhaltszusammenfassung zur Seite Nr. 2
BlueStorm Installation Guide, Connect Tech Inc. Limited Lifetime Warranty Connect Tech Inc. provides a Lifetime Warranty for all Connect Tech Inc. products. Should this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non Connect Tech Inc. authorized modification
Inhaltszusammenfassung zur Seite Nr. 3
BlueStorm Installation Guide, Connect Tech Inc. Table of Contents Limited Lifetime Warranty ..............................................................................................................................2 Copyright Notice..............................................................................................................................................2 Trademark Acknowledgment..........................................................................................
Inhaltszusammenfassung zur Seite Nr. 4
BlueStorm Installation Guide, Connect Tech Inc. List of Tables Table 1: DB-25 Female Pinouts for BlueStorm/LP (2 port connector) ........................................................ 13 Table 2: HDB-44 Pinouts for BlueStorm/LP (4 port connector).................................................................. 14 Table 3: VHDCI-68 Female pinouts for BlueStorm/LP (8 port connector) ................................................. 15 Table 4: HDB-78 pinouts for BlueStorm/SP (8 port conn
Inhaltszusammenfassung zur Seite Nr. 5
BlueStorm Installation Guide, Connect Tech Inc. Customer Support Overview If you experience difficulties after reading the manual and/or using the product, contact the Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties. In the event that the reseller is unable to resolve your problem, our highly qualified support staff can assist you. Our support section is available 24 hours a day, 7 days a
Inhaltszusammenfassung zur Seite Nr. 6
BlueStorm Installation Guide, Connect Tech Inc. Introduction Connect Tech Inc. presents BlueStorm/LP/SP/SP Opto and SP RJ-11. These high-speed multi- port communication adapters are designed for Low Profile (LP) and Standard Profile (SP) PCI compatible computers. BlueStorm cards provide you with up to eight high performance serial ports and baud rates up to 1.8432 Mbps that are compatible with any standard serial communications application. BlueStorm cards are fully PCI compliant.
Inhaltszusammenfassung zur Seite Nr. 7
BlueStorm Installation Guide, Connect Tech Inc. BlueStorm Installation Overview There are three stages to installing your BlueStorm card: 1. Hardware Configuration Interrupts and Memory selection will be set by the host computer’s BIOS and operating system. This section outlines jumper settings and configuration. 2. Hardware Installation Installation involves the physical installation of the BlueStorm into your computer. Please note that you should configure any jumper settings
Inhaltszusammenfassung zur Seite Nr. 8
BlueStorm Installation Guide, Connect Tech Inc. Multi-drop Slave Mode In this mode the TxD+/- line driver is enabled only when data is transmitted and RxD+/- is enabled all the time. This mode is typically used in multi-drop 4-wire connections. This mode requires software setup in Control Panel – System Properties – Hardware - Device Manager – Ports – CTI PCI UART. Click on Advanced under Port Settings. Line Bias/Termination The RS-422/485 transceivers, both transmit and receive are
Inhaltszusammenfassung zur Seite Nr. 9
BlueStorm Installation Guide, Connect Tech Inc. Figure 2: BlueStorm/LP jumper block locations, 4 port models Figure 3: BlueStorm/LP jumper block locations, 8 port models Revision 0.08 9
Inhaltszusammenfassung zur Seite Nr. 10
BlueStorm Installation Guide, Connect Tech Inc. Note: Jumper blocks are not installed for ports communicating in RS-232. Female HDB-78 • • • • • Jx • • • • • Jx1 Jx2 Jx3 Jx4 Jx5 JA = Port 1 JB = Port 2 JC = Port 3 JD = Port 4 JE = Port 5 JF = Port 6 JG = Port 7 JH = Port 8 Figure 4: BlueStorm/SP jumper block locations, 8 port models Note: Jumper blocks are not installed for ports communicating in RS-232. • • • • • Jx • • • • • Jx1 Jx2 Jx3 Jx4 Jx5 4
Inhaltszusammenfassung zur Seite Nr. 11
BlueStorm Installation Guide, Connect Tech Inc. Pin 1 Pin 1 6 x RJ-11 Figure 6: BlueStorm/SP RJ-11 diagram, 8 port model Note: Refer to Table 8 for port 7 and port 8 pinouts. Jumper Configuration for BlueStorm Jumper configurations will vary by model. BlueStorm/LP cards feature the jumper layout listed in Figure 7, while BlueStorm/SP and BlueStorm/SP Opto cards use the jumper layout in Figure 8. Lastly, BlueStorm/SP RJ-11 uses the jumper layout used in Figure 9. Figure 7
Inhaltszusammenfassung zur Seite Nr. 12
BlueStorm Installation Guide, Connect Tech Inc. JA JB JC JD TxD control JD1 JD1 JD1 JD1 RxD control JD2 JD2 JD2 JD2 JD3 JD3 JD3 JD3 RxD ± Termination/Bias JD4 JD4 JD4 JD4 RxD ± Termination/Bias JD5 JD5 JD5 JD5 TxD ± Termination Port 1 Port 3 Port 4 Port 2 Figure 7: Jumper configuration example for 4 port RS-422/485 BlueStorm/LP models JA JB JC JD JA0 JC0 RS-485 selection JB0 JD0 TxD control JA1 JC1 JB1 JD1 RxD control JA2 JC2 JB2 JD2 RxD ± Termination/Bias JA3
Inhaltszusammenfassung zur Seite Nr. 13
BlueStorm Installation Guide, Connect Tech Inc. Note that Auto 485 is a single jumper. The second site is not in use. See Figure 1 for the location of this jumper. Power-On Tri-state (BlueStorm/SP models only, excludes BlueStorm/SP RJ-11) BlueStorm/SP models offer a power-on tri-state similar to the Auto-485 mode listed above. The BlueStorm/SP implementation will tri-state ports configured as RS-485 full duplex. This is meant to ensure compatibility with our legacy Blue Heat/PCI card
Inhaltszusammenfassung zur Seite Nr. 14
BlueStorm Installation Guide, Connect Tech Inc. Table 2: HDB-44 Pinouts for BlueStorm/LP (4 port connector) Pin Port RS-232 Signal RS-422/485 Signal No. No. Signal Direction Signal Direction 1 1 TXD output TXD- output 2 1 RTS output RTS- output 3 1 DCD input RXD+ input 4 1 RXD input TXD+ output 5 2 TXD output TXD- output 6 2 RTS output RTS- output 7 2 DCD input RXD+ input 8 2 RXD input TXD+ output 9 3 TXD output TXD- output 10 3 RTS output RTS- output 11 3 DCD input RXD+ inpu
Inhaltszusammenfassung zur Seite Nr. 15
BlueStorm Installation Guide, Connect Tech Inc. Table 3: VHDCI-68 Female Pinouts for BlueStorm/LP (8 port connector) Pin Port RS-232 Signal RS-422/485 Signal No. No. Signal Direction Signal Direction 1 1 TXD output TXD- output 2 1 RI input CTS+ input 3 1 DCD input RXD+ input 4 1 DTR output RXD- input 5 1 RTS output RTS- output 6 1 DSR input CTS- input 7 1 RXD input TXD+ output 8 1 CTS input RTS+ output 9 2 TXD output TXD- output 10 2 RI input CTS+ input 11 2 DCD input RXD+ inpu
Inhaltszusammenfassung zur Seite Nr. 16
BlueStorm Installation Guide, Connect Tech Inc. Table 3: VHDCI-68 Female Pinouts for BlueStorm/LP (continued) Pin Port RS-232 Signal RS-422/485 Signal No. No. Signal Direction Signal Direction 47 6 RTS output RTS- output 48 6 DSR input CTS- input 49 6 RXD input TXD+ output 50 6 CTS input RTS+ output 51 5, 6 SG signal gnd. SR signal ref. 52 7, 8 SG signal gnd. SR signal ref. 53 7 TXD output TXD- output 54 7 RI input CTS+ input 55 7 DCD input RXD+ input 56 7 DTR output RXD- input
Inhaltszusammenfassung zur Seite Nr. 17
BlueStorm Installation Guide, Connect Tech Inc. Table 4: HDB-78 Pinouts for BlueStorm/SP (8 port connector) Pin Port RS- Signal RS-422/48 Signal No. No. 232 Direction 5 Direction Signal Signal 1 5 RTS output RTS A(-) output 2 5 CTS input RTS B(+) output 3 5 DSR input CTS A(-) input 4 5 RI input CTS B(+) input 5 5 SG signal gnd. SR signal ref. 6 6 RTS output RTS A(-) output 7 6 CTS input RTS B(+) output 8 6 DSR input CTS A(-) input 9 6 RI input CTS B(+) input 10 7 RTS output RTS
Inhaltszusammenfassung zur Seite Nr. 18
BlueStorm Installation Guide, Connect Tech Inc. Table 4: HDB-78 Pinouts for BlueStorm/SP (continued) Pin Port RS- Signal RS-422/48 Signal No. No. 232 Direction 5 Direction Signal Signal 40 1 RTS output RTS A(-) output 41 1 CTS input RTS B(+) output 42 1 DSR input CTS A(-) input 43 1 RI input CTS B(+) input 44 1 SG signal gnd. SR signal ref. 45 2 RTS output RTS A(-) output 46 2 CTS input RTS B(+) output 47 2 DSR input CTS A(-) input 48 2 RI input CTS B(+) input 49 3 RTS output R
Inhaltszusammenfassung zur Seite Nr. 19
BlueStorm Installation Guide, Connect Tech Inc. Table 5: RJ-45 Pinouts for BlueStorm/SP Opto (4 port connector) RS-232 RS-422/485 Pin No. Signal Direction Signal Direction 1 N/C no connect RTS (-) output 2 N/C input RxD (+) input 3 RTS output RTS (+) output 4 SG signal gnd SR signal ref. 5 TxD output TxD (+) output 6 RxD input RxD (-) input 7 Gnd ground Gnd. ground 8 CTS input CTS (+) input 9 N/C no connect TxD (-) output 10 N/C no connect CTS (-) input RJ-45 connector 1
Inhaltszusammenfassung zur Seite Nr. 20
BlueStorm Installation Guide, Connect Tech Inc. Table 6: Pinouts and Control Signals for DB-9 and DB-25 Male Connectors (BlueStorm/LP and BlueStorm/SP only) Pin # RS-232 RS-422/485 DB-9 DB-25 Signal Signal Direction Signal Signal Direction 1 8 DCD input RxD + input 2 3 RxD input TxD + output 3 2 TxD output TxD – output 4 20 DTR output RxD – input 5 7 SG signal gnd. SR signal ref. 6 6 DSR input CTS – input 7 4 RTS output RTS – output 8 5 CTS input RTS + output 9 22 RI input CTS
