Inhaltszusammenfassung zur Seite Nr. 1
PCI Scope Preprocessor
Users Manual-FSPCI64S
Copyright 1995 FuturePlus Systems Corporation
FuturePlus Systems and PCI Scope is a trademark of FuturePlus Systems Corporation
Revision 1.0
For Hewlett-Packard Logic Analysis Systems
LOCAL BUS
FuturePlus Systems Corporation
Inhaltszusammenfassung zur Seite Nr. 2
4 5 5 5 6 INTRODUCTION 7 7 8 Duplicating the Master Diskette 8 8 8 9 9 9 9 Connecting the MultiProbe Control Card to an Oscilloscope 10 11 Installation Quick Reference 11 Selecting the PCI signals to acquire 12 13 14 15 Characteristics 15 15 15 The PCI Present Pins 15 2 JTAG Boundary Scan Preprocessor Interface Compatibility GENERAL INFORMATION The PCI Personality Adapter option 101 Acquiring signals with an Oscilloscope AN
Inhaltszusammenfassung zur Seite Nr. 3
Standards Supported 15 15 15 Signal loading 15 Operations 16 Environmental Temperature 16 Altitude 16 16 Testing and Troubleshooting 16 Servicing 16 17 3 Signal Connections for the MultiProbe POD Humidity MultiProbe Pods required Power Requirements
Inhaltszusammenfassung zur Seite Nr. 4
How to reach us FuturePlus Systems can be reached at: FuturePlus Systems Corporation 36 Olde English Road Bedford, NH 03110 TEL:603-471-2734 FAX:603-471-2738 Internet: 71035.3052@compuserve.com WEB:www.futureplus.com FuturePlus Systems is represented in Japan by: 15-8, Minami-Shinagawa, 2-chome, Shinagawa-ku Tokyo 140 TEL:03-450-8101 FAX:03-450-8410 Contact : Mr. Takashi Ugajin Outside of Japan, FuturePlus Systems is represented world wide by Hewlett-Packard Co. Please contact your nearest Hewl
Inhaltszusammenfassung zur Seite Nr. 5
Product Warranty in material and workmanship for a period of 1 year from the date will, at its option, either replace or repair products proven to be defective. For warranty service or repair, this product must be returned to the factory. error-free. The foregoing warranty shall not apply to defects resulting from supplied software or interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for OTHER WARRANTY IS EXPRESSED OR IMPLIED. IMPLIED WARRANT
Inhaltszusammenfassung zur Seite Nr. 6
SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY. 6 products. For assistance, contact the factory. assistance agreements are available for FuturePlus Systems Assistance Product maintenance agreements and other customer
Inhaltszusammenfassung zur Seite Nr. 7
the MultiProbe connection point. are terminated with 10pf terminators at the maximum allowed the MultiProbe control module for analog analysis of the PCI This manual is organized to help you quickly find the information • The Analyzing the PCI Local Bus • The • The General Information information including the operating characteristics for the 7 PCI Scope Preprocessor module and the pinout. chapter provides some general
Inhaltszusammenfassung zur Seite Nr. 8
analysis system. This will help prevent the possibility of losing out, is damaged, or a file is accidentally deleted. in the disk menu of your logic analyzer. For more information, refer to the reference manual for the HP16500B mainframe. • interface circuit module. • • The minimum equipment required for complete analysis of a • • • 8 A 208 pin MultiProbe Pod (HP part number E5322A) An HP 16535A MultiProbe Control M
Inhaltszusammenfassung zur Seite Nr. 9
• • • LOCAL BUS SPECIFICATION - REVISION 2.1. That is, a # active state occurs when it is at a low voltage. The absence of a # symbol indicates that the signal is active at a high voltage. 208 pin MultiProbe pod. For information on how to configure the calibration fixture refer to the chapter on Analog Analysis in this 2. Align the 208 Pin MultiProbe Pod with the retainer that is nut. Install the affect the modules operation on a 32-bit PCI Local bus. pins. To load the files: HP16500B m
Inhaltszusammenfassung zur Seite Nr. 10
PCI_MUL.DUT and PCI.ADP from your PCI Scope 3. Access the configuration menu of the MultiProbe Control 4. Select POD setup for the POD that will be connected to the 5. On the next menu select #2 select the file PCI.ADP and select . 6. Return to the MultiProbe Configuration menu and Select 7. From the File selection menu select the MULTIPRB directory 6. Select the field next to File. Select the file PCI_MUL.DUT 7. Load the file With PCI_MUL displayed in the File field, select configured POD i
Inhaltszusammenfassung zur Seite Nr. 11
Load the PCI MultiProbe configuration file PCI_MUL.DUT from the MULTIPRB directory on the file. Once the file is loaded the POD that is connected to the PCI 11 as shown below Scope Preprocessor will be assigned the name PCI LogicScope hard disk. See page 9 for details on how to load this 2. the target PCI Local bus. Install the PCI Scope Preprocessor module into a slot in 1. Preprocessor module. Reference perform anal
Inhaltszusammenfassung zur Seite Nr. 12
Select Signals menu of the MultiProbe control module. a) Choose the output (Output 1 or Output 2) of the control module that is connected to the pod that is In the Select Signal menu, select the Output field to choose Output 1 or Output 2 of the control module. For example, Output D1 would be output 1 from the control module in slot D. b) Select the scope that you will use. In the Select Signal menu, select the scope field, then 3. Select the PCI signal for each output. time you want to choose a
Inhaltszusammenfassung zur Seite Nr. 13
MultiProbe field, then select the oscilloscope module. 2. Use the oscilloscope controls to run and adjust the If you need help, refer to the documentation on your 3. Select new signals. Signals field, the oscilloscope Scroll Signal field, or the MultiProbe Select Signal menu. Selecting signals from 13 glitch with FRAME# and the PCI clock appears below. A scope picture taken with the PCI Scope Preprocessor of a HP16534A
Inhaltszusammenfassung zur Seite Nr. 14
When the PCI Personality Adapter 101 is not in use, keep it in its original container. The file PCI.ADP matches the MultiProbe for PCI Analysis. If you wish to configure your own Programming the ground connections Installation guide and program all the even numbered 14 connections to ground. in your 208 MultiProbe High-Density Pod Personality adapter follow the instructions for configuration of the PCI Personality Adap
Inhaltszusammenfassung zur Seite Nr. 15
General Information This chapter provides additional reference information including Preprocessor Interface universal connector pinout. All PCI local bus ground pins of the Compatibility JTAG Boundary Scan The PCI Present Pins Standards Supported The PCI Local Bus Specification Revision 2.1 Power Requirements MultiProbe Pods required Signal loading Per the PCI Local Bus Specification the PCI Scope worst case load (10pf) at the maximum stub length. For
Inhaltszusammenfassung zur Seite Nr. 16
information on the electrical loading of the MultiProbe Pod refer to your Hewlett-Packard MultiProbe specification. Operations Environmental Temperature Altitude Operating: 4,6000m (15,000 ft) Humidity Testing and Troubleshooting Servicing module are damaged or lost contact the factory for a list of 16 replacement parts. replacement. However, if parts of the PCI Scope Preprocessor The repair strategy for the PCI Scope Pre
Inhaltszusammenfassung zur Seite Nr. 17
If the pin is not listed it is Grounded. POD PCI Signal PQFP pin 1 3 5 7 9 17 73 AD27 71 AD28 69 AD29 67 AD30 65 AD31 63 CLK 61 RST# 59 INTD# 57 INTC# 55 INTB# 53 INTA# 27 AD63 25 AD62 23 AD61 21 AD60 19 AD59 17 AD58 15 AD57 13 AD56 11 AD55 AD54 AD53 AD52 AD51 AD50 for the MultiProbe the PQFP package that acts as the MultiProbe Contact point. Signal Connections The below table shows the connection from the PCI Local Bus to
Inhaltszusammenfassung zur Seite Nr. 18
STOP# 18 135 AD10 133 AD11 131 AD12 129 AD13 127 AD14 125 AD15 123 C/BE1# 121 PAR 119 SERR# 117 SBO# 115 PERR# 113 SDONE 111 LOCK# 109 107 DEVSEL# 105 TRDY# 103 IRDY# 101 FRAME# 99 C/BE2# 97 AD16 95 AD17 93 AD18 91 AD19 89 AD20 87 AD21 85 AD22 83 AD23 81 C/BE3# 79 AD24 77 AD25 75 AD26
Inhaltszusammenfassung zur Seite Nr. 19
19 197 AD44 195 AD43 193 AD42 191 AD41 189 AD40 187 AD39 185 AD38 183 AD37 181 AD36 179 AD35 177 AD34 175 AD33 173 AD32 171 PAR64 169 C/BE4# 167 C/BE5# 165 C/BE6# 163 C/BE7# 161 REQ64# 159 ACK64# 157 AD00 155 AD01 153 AD02 151 AD03 149 AD04 147 AD05 145 AD06 143 AD07 141 AD08 139 C/BE0# 137 AD09
Inhaltszusammenfassung zur Seite Nr. 20
20 207 AD49 205 AD48 203 AD47 201 AD46 199 AD45
