Inhaltszusammenfassung zur Seite Nr. 1
SyncMaster 750B / 950B
Install drivers Install programs
Inhaltszusammenfassung zur Seite Nr. 2
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Inhaltszusammenfassung zur Seite Nr. 3
Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place
Inhaltszusammenfassung zur Seite Nr. 4
Do not drop the monitor when moving it. This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or personal injury. Do not place the product on an unstable or small surface area. Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically chil
Inhaltszusammenfassung zur Seite Nr. 5
Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance. Clean
Inhaltszusammenfassung zur Seite Nr. 6
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire. Others Do not remove cover (or ba
Inhaltszusammenfassung zur Seite Nr. 7
the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor. This may cause malfunction, an electric shock or fire. If a foreign substance enters the monitor, unplug the power
Inhaltszusammenfassung zur Seite Nr. 8
17,19 inch - 1280 X 1024 Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.
Inhaltszusammenfassung zur Seite Nr. 9
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor Manual User's Guide, Warranty Card Monitor Driver, Quick Setup Guide (Not available in all Natural Color software, locations) MagicTune™ software MagicRotation software Cable D-Sub Cable Power Cord DVI Cable
Inhaltszusammenfassung zur Seite Nr. 10
Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™ MagicBright™ is a new feature providing optimum viewing button [ ] environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™
Inhaltszusammenfassung zur Seite Nr. 11
Activates a highlighted menu item. / Enter button [ ] / Push the , then selects the video signal while the OSD is SOURCE button 'SOURCE' off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. Use this button for auto adjustment. AUTO button Thi
Inhaltszusammenfassung zur Seite Nr. 12
Connecting the Monitor Make sure to connect any cables to the monitor only when it is rotated. 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI port on th
Inhaltszusammenfassung zur Seite Nr. 13
Using the Stand Press and hold down the bottom of the stand and remove the fixing pin before use. A. Stand Stopper Pivot Stand Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Inhaltszusammenfassung zur Seite Nr. 14
A. Monitor Mounting interface pad B. 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. Installing the Monitor Driver (Automa
Inhaltszusammenfassung zur Seite Nr. 15
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage
Inhaltszusammenfassung zur Seite Nr. 16
Installing the Monitor Driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://w
Inhaltszusammenfassung zur Seite Nr. 17
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following " " window, then click the " " button. Then Message Continue Anyway click "OK" button. This monitor driver is under certifi
Inhaltszusammenfassung zur Seite Nr. 18
10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start" , "Setting" , "Control Panel". 2. Double click the "Display" Icon.
Inhaltszusammenfassung zur Seite Nr. 19
® ® Microsoft Windows NT Operating System 1. Click , , , and then double-click icon. Start Settings Control Panel Display 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower
Inhaltszusammenfassung zur Seite Nr. 20
For more information, refer to Help (F1) in the software program. How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD- ROM Drive, click the [Start] button of Windows and then select [Exec
