Inhaltszusammenfassung zur Seite Nr. 4
CONTENTS INTRODUCTION This manual explains how to correctly install, operate and get the best Introduction 1 performance from your monitor. Please read this user s manual carefully Product Features 2 before installing your monitor, then keep it near your monitor for quick reference. Setup 3 Installing the Tilt/Swivel Stand 3 First, please check that the contents of the carton box corresponds with the following checklist : Connecting the D-Sub Signal Cable 4 Connecting to Your Macintosh Compu
Inhaltszusammenfassung zur Seite Nr. 5
SETUP PRODUCT FEATURES INSTALLING THE TILT/SWIVEL STAND • The convenient and user-friendly on-screen display allows for 1. Ensure that the power to the monitor is off. easy and accurate adjustments of horizontal and vertical screen size and position, geometry and screen color. 2. Set the monitor face down with the underside facing you. Please be careful so as not to scratch the monitor screen. • The monitor supports a safe working environment in strict compliance with the MPR standard for l
Inhaltszusammenfassung zur Seite Nr. 6
CONNECTING THE D-SUB SIGNAL CABLE POWER MANAGEMENT SYSTEM If you use the monitor with a computer which complies with the power 1. Turn off the computer and monitor. saving program, you can set the monitor to go blank when the system has remained unused for a period of time. To specify the period or to disable 2. Connect the 15 pin D-sub connector to the output port of the this feature, set the system timeout field of the computer s system setup video card in your computer. program or use specia
Inhaltszusammenfassung zur Seite Nr. 7
OPERATION & ADJUSTMENT 1. OSD(On-Screen Display) Menu 1 + - EXIT ADJUST SELECT MENU Adjust the contrast of image, the difference MENU : Launch OSD(On-Screen Display) Menus - + between light and dark areas on the screen. 50% : Select the next function Range : 0 -100 % CONTRAST : Select the previous function : Increase the value of any selected function - + : Decrease the value of any selected function Adjust the brightness of the entire display. 50% EXIT : Exit OSD Menus & Launch
Inhaltszusammenfassung zur Seite Nr. 8
2. OSD (On-Screen Display) Menu 2 3. OSD (On-Screen Display) Menu 3 Adjust the left and right margins for more convex or more concave margins. - + Adjust the position of the display horizontally Image turns to by . - + 50% 50% (left or right). Image turns to by . PINCUSHION HORIZONTAL POSITION Adjust the trapezoid of the screen by moving the lines inward or outward. - + Image turns to by . - + Adjust the display width (horizontal
Inhaltszusammenfassung zur Seite Nr. 9
SPECIFICATIONS Picture Tube Type : 15-inch, Flat Square Tube type Tilt/Swivel Range Tilt : 5 forward, 10 backward (14-inch, viewing area) Swivel : 45 leftward, rightward Dot Pitch : 0.28mm, MPR II Face Treatment : Non-glare / Anti-static Dimension 368(W) 394(D) 382(H) mm (set with stand) Video Input Signal : R.G.B. Analog Amp. Bandwidth : 85 MHz Weight(net/gross) 12.5 / 14.2 Kg Input Sync : TTL, separate negative / positive 27.6 / 31.4 lbs Scan Fr
Inhaltszusammenfassung zur Seite Nr. 10
TROUBLESHOOTING DESCRIPTION FOR D-SUB CONNECTOR Symptom Check Pin Signal No picture. Check if POWER SWITCH and COMPUTER POWER SWITCH are in the on position. 1 Red 1 2 Green Check if the signal cable is correctly connected to 3 Blue the video card. 4 GND 6 10 5 GND(Self-Test) Check if the pins of D-sub connector are not bent. 6 GND-Red 15 7 GND-Green Check if the computer is in the power saving mode. 8 GND-Blue 9 No Pin Check if POWER SWITCH is in the on position. 10 GND-H.Sync POWER LED is not
Inhaltszusammenfassung zur Seite Nr. 1
COLOR MONITOR
Model No : CTL 5fln
CTL
S/N:9978623807A
USER S GUIDE
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFEGUARDS FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT 1. Read all of these instructions. 12. For added protection for this NOTE : This equipment has been tested and found to comply with the limits for a monitor during a lightning storm, 2. Save these instructions for later use. or when it is left unattended and Class B digital device, prusuant to Part 15 of the FCC Rules. These limits in a unused for long periods of time, 3. Unplug this monitor from th
Inhaltszusammenfassung zur Seite Nr. 3
The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. As an ENERGY STAR Partner, Computer Technology Link, Inc., has determined that this product meets the Energy Star guidelines for energy efficiency.
