Inhaltszusammenfassung zur Seite Nr. 1
Marshall Electronics
Model No. V-R261-DLW
26" Full Resolution Dual Link / Waveform Monitor
Operating Instructions
Inhaltszusammenfassung zur Seite Nr. 2
This page intentionally left blank 2
Inhaltszusammenfassung zur Seite Nr. 3
Contents Features............................................................................................................................................................4 Installation and Initial Setup .......................................................................................................................5 Unpacking....................................................................................................................................................................
Inhaltszusammenfassung zur Seite Nr. 4
Features The V-R261-DLW (Dual Link / Waveform) monitor is the latest addition to Marshall's expanding line of IMD-equipped monitors. ■ ■ 1920 x 1200 Full Resolution 26” Panel In-Monitor Display The V-R261-DLW features an all-digital TFT- In-Monitor Display allows on-screen text and tally MegaPixel active matrix LCD system with 1920x1200 indication, controlled locally or remotely via a variety native resolution. The LCD panel features a of industry standard protocols. 2 brightness of 500 cd/m and
Inhaltszusammenfassung zur Seite Nr. 5
Installation and Initial Setup ■ Unpacking Carefully unpack the V-R261-DLW monitor and verify that the following items are included: • V-R261-DLW Monitor • V-PS24-7.5 Power Supply with XLR Connector • Operating Instructions Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States, call +1 (310) 333-0606. ■ Installation The V-R
Inhaltszusammenfassung zur Seite Nr. 6
Front Panel Features Power Button Layout Button Turn the monitor off or on by pressing the power Use this button to switch between the four available button. The LED on the power button is at layouts on the V-R261-DLW. maximum illumination when the unit is OFF. The RotoMenu ™ Knob LED is at minimum illumination when the unit is on. The RotoMenu ™ knob allows for accessing and Input Channel Buttons navigating the main menu, using only a single control. Pressing SDI 1 or SDI 2 will select HDSDI-SD
Inhaltszusammenfassung zur Seite Nr. 7
Rear Panel Features RS-422/485 Serial Interface The RS-422/485 ports are used to remotely control Power Input the IMD or all V-R261-DLW features, using a variety of industry standard protocols. (Note: Connect the 24 VDC input to the XLR power input Connector/pin-out may need to be adapted connector. Power can be supplied from the included depending on protocol and controlling device power supply or from a variety of DC sources supplying at used.) Only one connection to either port is needed leas
Inhaltszusammenfassung zur Seite Nr. 8
Compatible Input Formats The following SDI standards are supported by the V-R261-DLW: 525i, 625i 1035i (60 / 59.94) 1080i (60 / 59.94 / 50) 1080psF (24 / 23.98) 1080p (23.98 / 24 / 25 / 29.97 / 30) 720p (60 / 59.94 / 50) 720p (23.98 / 24 / 25 / 29.97 / 30) The following 3G-SDI standards are supported by the V-R261-DLW: YCbCr (4:2:2) 10 Bit - Level A / B 1080p (60 / 59.94 / 50) YCbCr/RGB (4:4:4 / 4:2:2) 10 Bit / 12 Bit - Level A / B 1080i (60 / 59.94 / 50) 1080p (30 / 29.97/ 25 / 24 / 23.98) 1080
Inhaltszusammenfassung zur Seite Nr. 9
DLW Monitor Layouts The V-R261-DLW has 4 possible layouts, Multi mode, Vectorscope mode, Waveform mode and Full Screen Video mode. Each press of the LAYOUT Button will change the current mode to next available mode. Default Multi mode Layout Vectorscope Mode 9
Inhaltszusammenfassung zur Seite Nr. 10
Waveform Monitor Mode Full Screen Video Mode 10
Inhaltszusammenfassung zur Seite Nr. 11
On-Screen Menu STRUCTURE OVERVIEW 11
Inhaltszusammenfassung zur Seite Nr. 12
On-Screen Menu (continued) MAIN MENU AND NAVIGATION Access and navigate the main menu using the RotoMenu ™ knob: Main Menu Using the RotoMenu knob • Press the RotoMenu ™ knob to enter the main menu. • Rotate the knob to scroll up or down in the main menu or each submenu. • Press the RotoMenu ™ knob to enter a submenu or choose a setting. • To return to main menu from submenu, select ‘Back’ and press the RotoMenu ™. The menu timeout can be set in the OSD Timeout section of the OSD Config submenu.
Inhaltszusammenfassung zur Seite Nr. 13
■ 16:9 Markers Use this setting to superimpose one of 10 markers on the screen when in 16:9 or Full Screen mode. This setting is disabled when the aspect ratio is set to 4:3, or when Pixel-to-Pixel mode is enabled. Note that in Full Screen mode, markers are vertically stretched along with the picture to fit the 16:10 screen. • Off (No Marker) • 95% Safe Area • 93% Safe Area • 90% Safe Area • 88% Safe Area • 80% Safe Area • 1.85:1 Aspect Ratio • 2.35:1 Aspect Ratio • 4:3 Aspect Ratio • 14:9 Aspec
Inhaltszusammenfassung zur Seite Nr. 14
4:3 Marker Examples: OFF (No Marker) 90% Safe Area ■ Marker Background Use this setting to choose how selected markers are displayed on the screen: • Off The marker is superimposed on the complete image. • 50% Gray Screen area beyond the marker is shown at 50% intensity. • Black Screen area beyond the marker is shown as black. Example (80% Marker in 4:3 Mode): Background OFF 50% Gray Background Black Background ■ Center Marker Use this setting to display a center marker on the screen. Center Mar
Inhaltszusammenfassung zur Seite Nr. 15
Video Config Submenu Use the Video Configuration submenu to select various video settings such as monochrome mode or blue-only mode. Video Configuration Submenu ■ Monochrome Mode Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale picture. ■ Blue-Only Mode Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching off the red and green components. Use this mode when calibrating the m
Inhaltszusammenfassung zur Seite Nr. 16
■ Pixel-to-Pixel Mode Use this setting to enable Pixel-to-Pixel mode. This mode bypasses the monitor’s internal scaling function and displays images in their native resolution and aspect ratio, with a one-to-one mapping of incoming image pixels to screen pixels: • For incoming formats smaller than the native resolution of the window (or selected aspect ratio), the image will be displayed in the center of the window using only the necessary LCD pixels. For example, 480i images will only occupy ex
Inhaltszusammenfassung zur Seite Nr. 17
■ Curtain Color Use this setting to choose the default color displayed on the screen when no video input is present. Available colors are blue, red, green, white, and black. ■ Ctemp/Gamma Use this setting to choose one of three color temperature / gamma presets or to remove gamma settings: • Linear (No gamma applied) • 55K • 65K • 93K ■ Analog Phase (DVI-Analog or VGA input only) Adjusts the analog phase value to improve picture quality on DVI-A or VGA Sources. This adjusts the signal phase (not
Inhaltszusammenfassung zur Seite Nr. 18
■ HDMI CSC Auto (HDMI input only, via the DVI-I interface) The HDMI CSC Auto setting is used to accommodate newer HDMI interfaces that send colorspace signaling in the HDMI data stream. If this setting is set to On, the monitor will automatically determine which colorspace setting to use. If this setting is set to Off, or your HDMI signal does not contain colorspace signaling, the DVI-D CSC Mode described above will determine the colorspace configuration. Color Config Submenu Use the Color Confi
Inhaltszusammenfassung zur Seite Nr. 19
■ User-Definable Function Buttons Use the Function 1, Function 2, Function 3 and Function 4 menu items to define each function button on the front panel of the monitor. The following options are available for each button: • Marker Toggle between different Screen Markers • Center Marker Display/hide the Center Marker • Marker Backgrd Change how markers are displayed on the screen • IMD State Display/hide IMD text • Anc. Time Code Display/hide time code • OSD Tally Rotate amongst types of OSD Tall
Inhaltszusammenfassung zur Seite Nr. 20
OSD Config Submenu Use the OSD Configuration submenu to select a variety of information to be displayed on the screen. OSD Configuration Submenu ■ IMD State Use this setting to turn the IMD text display on or off. This setting affects both fixed string IMD text and remote IMD text commands. ■ Status Display Use this setting to enable or disable status display. When enabled, the current video input standard is displayed on the top left of the screen. When disabled, status is only displayed for 2
