Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
Safety Guidelines Caution: Always use a power cable is properly grounded. Please use the AC cords listed below for each area: USA ........................ UL Canada ...................CSA/cUL FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equi
Resumen del contenido incluido en la página 3
IMPORTANT SAFEGUARDS Important Safeguards Before using your TV, please read these instructions completely, and keep this manual for future refer- ence. Carefully observe and comply with all warnings, cautions and instructions placed on the unit or described in the operating instructions or service manual. The User Manual uses the following symbols, to ensure a safe operation and prevent any dam- age to operators or properties: WARNING ----- Ignorance or inappropriate use may cause damage to
Resumen del contenido incluido en la página 4
Never use a damaged power cord: Heavy objects, heat, or tensile force may damage the power cord and cause fire or electric shock. Never block or cover the slots or openings, in the TV cabinet back, bottom, and sides. Never place the TV: - on a bed, sofa, rug, or similar surface; - too close to drapes, curtains, or walls; or - in a confined space such as bookcase, built-in cabinet, or any other place with poor ventilation. The slots and openings are provided to protect the TV from overheating an
Resumen del contenido incluido en la página 5
IMPORTANT SAFEGUARDS The power cable should be kept away from heat sources: The heat produced by any heat source may melt the covering of the power cable. Unplug the connector Hold the power connector when removing the power cable: Pulling the power cable itself may damage the vires inside the cable and cause fire or electric shock. Do not touch the connector with wet hands: To avoid risk of electric shock. ATTENTION Insert batteries in accordance with instructions: Insert the batteries with corr
Resumen del contenido incluido en la página 6
Although the LCD screen is made with high-precision technology and has effective pixels of 99.99% or more, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD panel and is not a malfunction. LCD (Liquid Crystal Display) may cause interference in image, sound, etc.of the other electronic equipment that is easy to receive electromagnetic waves (i.e. AM radios and video equipme
Resumen del contenido incluido en la página 7
CONTENTS BEFORE USE Contents Adjustment of “Balance” ..................24 Safety Guidelines ..............................1 Selection of “Surround” ....................24 Important Safeguards ........................ 2 Using the Setup Menu ........................25 Precaution .........................................5 Selection of “Language” ...................25 1. Before use .....................................7 Setting of “V-Chip” ...........................25 1.1 Open the Pa
Resumen del contenido incluido en la página 8
1. Before use The product is a 37” WXGA (WXGA resolution) LCD TV Player. It has passed the UL and cUL safety certifications, and is an ideal product for personal and commercial use. The product is a precise electronic product. Users should read the following instructions carefully to maximize the performance and life span of the product: 1.1 Open the Package - The product is packaged in a carton together with other standard accessories. Any optional accessories shall be packed sepa
Resumen del contenido incluido en la página 9
PRODUCT FEATURES PRODUCT FEATURES SIDE VIEW FRONT VIEW 2. Product Features The 37” LCD TV Player provides quality image displays and is suitable for a variety of multi media applications: 1. Available input signals - The product provides HDMI input connector. - The product provides VGA (D-Sub 15 PIN) input connector. - The product supports PC images resolutions up to (1024 x 768@60Hz) with a vertical frequency of 60Hz. - The product provides component video (RCA) input connectors.
Resumen del contenido incluido en la página 10
4. Names and Functions of Parts 4.1 Side View The functions of the buttons are described as follows: Sketch map STANDBY: Press (Standby) to turn on and turn off. VOL.+/- A. They are used as buttons in the OSD Menu screen. B. Press to adjust the volume. CH.+/- A. They are used as buttons in the OSD Menu screen. B. Press to scan through channels. To scan quickly through channels, press and hold down either channels. MENU: Press to display the menu. Press agai
Resumen del contenido incluido en la página 11
REAR VIEW REMOTE CONTROL 4.3 Rear View Sketch map Push the power switch (O: Off, I: On). Use the power cord connect to an earthed 120V, 60Hz AC outlet. Signal input and other terminals: ANT1 & ANT2: 75Ω Coaxial connector for Antenna/Cable Network. Note: ANT 1 is for ATSC (DTV), and ANT 2 is for NTSC. (Refer to page 16.) OPTICAL OUTPUT: Connect the optical output to the optical input connector of the Amplifier. (Only for DTV) RS-232: The D-SUB 9 Pins terminal i
Resumen del contenido incluido en la página 12
4.4 Remote Control Power ( ): Press to turn on and off. Mute ( ): Press to mute the sound. Press again or press VOL+/- to restore the sound. 0~9 Number Buttons: In TV mode, press 0~9 to select a channel; the channel changes after 2 seconds. EPG: Press to display EPG(Electronic Program Guide) menu. Source ( ): Press to select the signal sources. DTV: Press to select Digital TV mode. Dot: Press number buttons with it to select the channels directly in
Resumen del contenido incluido en la página 13
REMOTE CONTROL CONNECT ACCESSORY DEVICES Insertion of Batteries - Turn the remote control upside down, press and slide off the battery cover. - Insert two 1.5V (AAA) batteries into the compartment, take care to observe the and markings indicated inside. - Replace the cover and slide in reverse until the lock snaps. Sketch map Range of Remote Control - Ensure the remote control is pointed towards the Remote control window on the display unit. - No obstacles should be placed between
Resumen del contenido incluido en la página 14
5. Connect Accessory Devices Connecting a DVD player or other equipment Switch off LCD TV and external equipment before connecting cables. 1. Connect a DVD player or other equipment’s Component Video Out (Y,Pb,Pr/Y,Cb,Cr) to the LCD TV’s corresponding Component In (Y,Pb,Pr/Y,Cb,Cr) terminal on COMP1 or COMP2. Green Red 2. Connect a DVD player’s Audio Out to the TV Blue Component L/R terminal. White Red 3. Press Power to turn on the LCD TV, then turn on external equipmen
Resumen del contenido incluido en la página 15
CONNECT ACCESSORY DEVICES Connecting the DVD player or HDTV Set-top box using HDMI input Switch off TV and external equipment before connecting cables. 1. Connect the LCD TV to the DVD player or HDTV Set-top box with the HDMI cable. 2. Connect the DVI AUDIO input terminal to the audio output terminal of HDTV Set-top box with DVI output terminal, and a DVI to HDMI conversion cable should be adopted. 3. Press ensure the power cord is connected and press the power switch button turned on be
Resumen del contenido incluido en la página 16
Connecting the DVD or VCR player devices Switch off TV and external equipment before connecting cables. 1. Connect a DVD or VCR player’s Video Out to the TV’s Video In terminal by a Video cable. 2. Connect a DVD or VCR player’s S-VIDEO Out to the TV’s S-VIDEO In terminal by a S-VIDEO cable. 3. Connect a DVD or VCR player’s Audio Out to the TV’s L/R terminal by a Audio cable. 4. Press Power to turn on the TV, then turn on external equipment. 5. Press Source to select AV or S-VIDEO si
Resumen del contenido incluido en la página 17
CONNECT ACCESSORY DEVICES BASIC OPERATION Connect to antenna ATSC (DTV) & NTSC input connection config 1. There are two Antennas: - ANT 1 is only for ATSC channel of Air. - ANT 2 is only for Air or Cable Signal of NTSC. 2. The user can select the Antenna input as below: A. One Antenna is for Air signal config. Splitter ANT 1 (DTV) ANT 2 (NTSC) Air Signal (NTSC + ATSC) B. Two Antenna config A ANT 1 is only for ATSC channel of Air. ANT 2 is only for Cable signal of NTSC. Air Si
Resumen del contenido incluido en la página 18
6. Basic Operation 6.1 Power ON/OFF The Display is in Standby mode. - Press the Power on the remote control or on the control panel to turn on the unit. The power indicator changes from red to green. Power - Press the Power on the remote control or on the control panel again to return the display to standby mode. The power indicator changes from green to red. Note: For protecting your LCD TV product, the interval time between turn on the LCD TV product and Source shu
Resumen del contenido incluido en la página 19
USING THE PIP/PBP FEATURE 6.4 Using the PIP/PBP feature The PIP (picture-in-picture) /PBP (picture-in-picture) feature splits the screen into a double window that allows you to watch two programs at the same time. The POP program can come from a TV broadcast or an external source, such as a VCR. To enter the PIP/PBP window: Press PIP for selecting the different PIP modes, such as following; Full Screen Picture Source PIP Picture PBP Picture Use Swap button to select the wi
Resumen del contenido incluido en la página 20
To display a picture from an external source in the PIP/PBP window: 1. Connect the external source equipment. (refer to Connect Accessory Devices page.) 2. Select the TV program you want to watch. 3. Press PIP to display the PIP/PBP window. 4. Repeatedly press Source to select the input source for the PIP/PBP window. To change the PIP position: Press PIP Pos. button to change the PIP window position under PIP mode, it display as following; Right Left Left Right
