Resumen del contenido incluido en la página 1
TYPHOON
L50B Pro
opErAting instructions
Please keep for future reference
Thank you for purchasing this Typhoon L50B Pro charger. We are sure you will be pleased
with its performance and features. In order to ensure that you obtain the maximum benefit
from its operation, please read these instructions carefully.
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
SpEciFicAtions Input Voltage 11~15V DC Battery Type & Cells 1~5 Lithium-Ion or Lithium-Polymer cells (3.6V or 3.7V respectively) 1~6 LiFePO4 cells (3.3V) 1~14 Nickel-Cadmium cells 1~14 Nickel-Metal Hydride cells 1 - 6 Lead-Acid cells (2V per cell) Battery Capacity 100mAh ~ 6000mAh adjustable ONLY for Lithium-Ion, Lithium-Polymer and LiFePO4 Charge Rate 0.1A ~ 6A Adjustable in 100mA steps (2C charge rate available for Li-Po Batteies) Trickle Charge Rate 0 ~ 200mA Balancing Max.
Resumen del contenido incluido en la página 4
SAFEty prEcAutions • DO NOT attempt to charge incompatible types of rechargeable batteries. This charger is designed to only charge and discharge Nickel-Cadmium, Nickel-Metal Hydride, Lithium-Ion, Lithium-Polymer, LiFePO4 and Lead- Acid batteries. • Mak e sure y ou place the charger on a firm lev el surfac e for charging. • DO NOT attempt to charge batteries at excessive fast charge currents. Check with your battery manufacturer for the maximum charge rate applicable to your ba
Resumen del contenido incluido en la página 5
Lithium Ion/polymEr BAttEry SAFEty WArnings Ensure that the charger and battery are placed on a non-flammable surface whilst charging and ideally charge outdoors wherever possible. NEVER charge a Lithium ION/Polymer/Fe battery inside a vehicle whatever the circumstances. ALWAYS ensure that the charger is correctly set for the battery being charged, checking both voltage and capacity. Be particularly careful if using a series/parallel battery pack, or if using packs of different specificati
Resumen del contenido incluido en la página 6
Lithium Ion/polymEr/FE BAttEriEs Lithium battery packs must NEVER be discharged below 3 volts per cell as this will result in damage to the cells. If the voltage is allowed to drop below 3 volts per cell the battery voltage may seem to recover following a charge, but the battery may not then give its full nominal capacity and a reduction in performance is likely – allowing the voltage to drop below 3 volts per cell will invalidate all warranty claims. NEVER charge Lithium Polymer battery pa
Resumen del contenido incluido en la página 7
Input powEr 12V DC Connect the charger’s red alligator clip to the positive (+) terminal on the power source and the black alligator clip to the negative (-) terminal. The charger will display “Input voltage” error message if the input is below 11V or above 15V. If this happens, please recheck the input power supply to make sure correct power is present. Output BAttEry ConnEctions Two 4mm banana sockets are located on the right side of the charger. Connect the battery main power leads to t
Resumen del contenido incluido en la página 8
OpErAtion • When the charger is connected to the power source the charger will show the • If the other buttons are pressed, or nothing is pressed, the present battery type battery mode that was last used. stops flashing. • If the battery TYPE button is briefly pressed, the present battery type (NiCd, NiMH, • If the Battery TYPE button is pressed and briefly held, the recent & previous data Lithium, or Pb ) will flash. While the existing battery type is flashing, every time will be shown u
Resumen del contenido incluido en la página 9
• When the charger is connected to the power source the charger will show the • If the other buttons are pressed, or nothing is pressed, the present battery type battery mode that was last used. stops flashing. • If the battery TYPE button is briefly pressed, the present battery type (NiCd, NiMH, • If the Battery TYPE button is pressed and briefly held, the recent & previous data Lithium, or Pb ) will flash. While the existing battery type is flashing, every time will be shown until the B
Resumen del contenido incluido en la página 10
Lithium Modes (Li-Ion/Li-Po/Li-Fe) BATT TYPE INC Lilo CHARGE 3.0A Lithium Type C=3000mAh 10.8Vp Lilo DEC ENTER ENTER INC DEC Lilo CHARGE 3.0A Lithium Type C=3000mAh 10.8Vp Lilo ENTER DEC INC DEC INC Lilo CHARGE 3.0A Lithium Type C=3000mAh 10.8Vp LiPo ENTER DEC INC DEC INC Lilo CHARGE 3.0A Lithium Type C=3000mAh 10.8Vp LiFe START BALANCER CON. BALANCER CON. NOT CONNECTED CONNECTED BATTERY CHECK WAIT PLEASE.... CHG 0:00 00000 LI + 3.00A 12.000V This charger is capable of charging up
Resumen del contenido incluido en la página 11
Setting Battery Voltages For Li-Po Battery Pack LiPo CHARGE 3.0A Select the correct total battery voltage to be charged with C=3000mAh 11.1Vp the INC & DEC buttons – 3.7V, 7.4V, 11.1V, 14.8V and 18.5V [Vpack]. Setting Battery Voltages For Li-Fe Battery Pack LiFe CHARGE 3.0A Select the correct total battery voltage to be charged with the C=3000mAh 11.1Vp INC & DEC buttons – 3.3V, 6.6V, 9.9V, 13.2V and 16.5V [Vpack]. Setting Charge Current Lilo CHARGE 3.0A Always set the capacity firs
Resumen del contenido incluido en la página 12
Pb Mode BATT TYPE PB CHARGE C=3.0A 12Vpack ENTER INC DEC PB CHARGE C=3.0A 12Vpack ENTER INC DEC PB CHARGE C=3.0A 12Vpack START BATTERY CHECK WAIT PLEASE.... CHG 0:00 00000 PB + 3.0 A 12.000V to NiCd charge Setting Charge Current PB CHARGE Adjust the desired charge current, which ranges from 0.1A to C=3.0A 12Vpack 6.0A with the INC & DEC buttons. Press the ENTER button to confirm the setting. Setting Battery Voltages For a Lead-Acid (Pb) PB CHARGE Battery Pack C=3.0A 12Vpack Se
Resumen del contenido incluido en la página 13
ScrEEn DisplAys Displays During Charge “BLC” will be shown if the balancer cable of the battery is connected to the balancing port of the charger. CHG 0.30:25 00000 CHG: Charge NC + 3.00A 5.200V If the Enter button is pressed at any NC = NiCd stage, the charge can be terminated. NM = NiMH Ll = Lilo, LP = LiPo, LF = LiFe Pb = Pb Completion Display (with Audible Warning) In order to move to the main display, press the Enter button. END 030:00 00000 NC 100mA 10.750V Data Display In ord
Resumen del contenido incluido en la página 14
Error mEssAgEs Input voltage is below 11.0V or exceeds 15V. INPUT BATTERY VOLTAGE ERROR Battery is not connected to the charger’s output banana NO BATTERY sockets. Battery is connected to the output banana sockets in OUTPUT BATTERY reverse. REVERSE POLARITY The circuit of the charger has a problem. OUTPUT CIRCUIT PROBLEM Battery has become disconnected during an operation. CHECK THE BATT. OPEN CIRCUIT Wrong voltage is set while charging Lithium or Pb batteries. CHECK THE BATT. OVER VOLTAGE Wro
Resumen del contenido incluido en la página 15
Resumen del contenido incluido en la página 16
www.LogicrC.com Logic RC Limited 14 Hartham Lane Herford SG14 1QN United Kingdom
