Resumen del contenido incluido en la página 1
Operator´s manual
Rider 155
Please read these instructions carefully and make sure
you understand them before using the machine. English
Resumen del contenido incluido en la página 2
Svenska – 31 Sve-5 225/232/235 Bruk 31 97-11-25, 08.46
Resumen del contenido incluido en la página 3
CONTENTS Operator’s Manual for Rider 155 Safety rules for USA ........................................... 2 Adjusting the brake ........................................ 25 Introduction ......................................................... 4 Adjusting the throttle wire ............................... 26 Driving and transport on public roads .............. 4 Service of air filter .......................................... 27 Towing ..............................................................
Resumen del contenido incluido en la página 4
1. Safety rules for USA These instructions are for your safety. Read them carefully. Safe operation practices for ride-on mowers IMPORTANT! This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Use slow speed. Choose a low gear so that I. General operation you will not have to stop or shift while on the 1. Read, understand and follow all instructions in slope. the manual and
Resumen del contenido incluido en la página 5
1. Safety rules for USA Travel and transport on public roads IV. Service Check the relevant road traffic regulations before 1. Use extra care in handling gasoline and other driving the machine on a public road. If transporting fuels. They are flammable and vapours are the machine on another vehicle always use explosive. approved securing devices and make sure that the machine is securely held. a) Use only an approved container. b) Never remove gas cap or add fuel with the engine running. Allow
Resumen del contenido incluido en la página 6
INTRODUCTION Dear customer Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a frontmounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. Collected controls and a hydrostatic transmission controlled by pedals also contribute to the machine’s performance. We hope you will find this operator’s manual very useful. By following its instructions (on operation, service, main
Resumen del contenido incluido en la página 7
INTRODUCTION Good service Husqvarna products are sold all over the world and only through servicing dealers. This is to ensure that you, the customer, get the best support and service. When you need spare parts or advice on service issues, warranty terms, etc., contact: Engine Transmission This Operator’s Manual belongs to machine with serial number: Serial number The serial number can be found on the printed plate attached to the front, left-hand side under the seat. Stated on the plate, from t
Resumen del contenido incluido en la página 8
EXPLANATION OF SYMBOLS These symbols are on the machine and in the operator’s manual. Study them carefully so that you know what they mean. Read the operator’s manual N R Reverse Neutral Fast Slow Engine off Battery Choke Fuel Oil level Cutting height Backwards Forwards Ignition Hydrostatic free wheel Use hearing protection Parking brake Brake Warning Warning! Never carry passengers on the Never use the machine if persons, especially Never drive across a Risk that the machine or equipmen
Resumen del contenido incluido en la página 9
EXPLANATION OF SYMBOLS Placards 8009-442 English – 7
Resumen del contenido incluido en la página 10
SAFETY INSTRUCTIONS Safety instructions These instructions are for your safety. Read them carefully. WARNING! The inserted symbol means that important safety instructions need to be observed. It applies to your safety. General use • Read all the instructions in this operator’s manual and on the machine before you start it. Ensure you understand them and then observe them. • Learn how to use the machine and its controls safely and learn to how to stop quickly. Also learn to recognize the safety d
Resumen del contenido incluido en la página 11
SAFETY INSTRUCTIONS • Take care when rounding a fixed object, so that WARNING! the blades do not hit it. Never run the machine Engine exhaust, some of its over foreign objects. constituents and certain vehicle components contain or emit • Only use the machine in daylight or in other chemicals considered to cause well-lit conditions. Keep the machine at a safe cancer, birth defects or other distance from holes or other irregularities in the reproductive impairment. The ground. Pay attention to ot
Resumen del contenido incluido en la página 12
SAFETY INSTRUCTIONS Driving on slopes Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest; this can result in serious injury or death. All slopes demand extra care. If you cannot reverse up a slope or if you feel unsure, do not mow it. Proceed as follows: • Remove obstacles such as stones, branches, etc. 6003-004 • Mow upwards and downwards, not sideways. Mow upwards and downwards on slopes, not sideways. • Do
Resumen del contenido incluido en la página 13
SAFETY INSTRUCTIONS Children • Serious accidents may occur if you fail to be on your guard for children in the vicinity of the machine. Children are often attracted to the machine and mowing. Never assume that children will remain where you last saw them. • Keep children away from the area to be mowed and under close supervision by another adult. • Keep an eye out and shut off the machine if children enter the work area. • Before and during reversing procedures, look behind you and down for smal
Resumen del contenido incluido en la página 14
SAFETY INSTRUCTIONS • If leaks arise in the fuel system, the engine must not be started until the problem has been resolved. • Store the machine and fuel in such a way that there is no risk that leaking fuel or fumes can cause any damage. • Check the fuel level before each use and leave space for the fuel to expand, because the heat WARNING! from the engine and the sun may otherwise The engine and the exhaust system become very hot during cause the fuel to expand and overflow. operation. • Avoid
Resumen del contenido incluido en la página 15
SAFETY INSTRUCTIONS • Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas. • Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting. • Never make adjustments with the engine running. • The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. • The blades are sharp and can cause cut
Resumen del contenido incluido en la página 16
PRESENTATION Presentation The power transmission from the engine is handled Congratulations on your choice of a top quality by a hydrostatic gearbox, which allows variable product which you will enjoy for many years. variation of the speed by using the pedals. These instructions describe the Rider 155. This rider mower is equipped with a 15.5 horsepower There is one pedal for driving forwards and one Kohler engine. pedal for reversing. 6017-213 8009-114 Location of the controls 1. Ignition lock
Resumen del contenido incluido en la página 17
PRESENTATION Throttle and Choke lever The engine speed is adjusted with the throttle control, and thereby also the rotation speed of the blades. The control is also used to activate the choke function. When the choke is used the engine receives a richer mixture of fuel and air, which simplifies cold start. 6004-004H Speed limiter 2 1 The speed of the machine is steplessly regulated with two pedals. Pedal (1) is used to drive forwards and pedal (2) for reversing. WARNING! Make sure that branches
Resumen del contenido incluido en la página 18
PRESENTATION Cutting unit The Rider 155 is equipped with cutting unit. • Combi - 1030 mm/41" The combi deck functions as a mulching deck when a BioClip plug is mounted. Otherwise, the deck will function as a rear ejection deck. 6017-214 Lift lever for cutting unit The lift lever is used to set the cutting unit in transport or cutting position. If the lever is pulled back the unit will lift up and the blades will automatically stop rotating (transport position). If the lock button is pressed and
Resumen del contenido incluido en la página 19
PRESENTATION Lever for adjustment of cutting height With this lever the cutting height can be adjusted to 9 different positions. Combi 103 unit, 45-95 mm (1 3/4" - 3 3/4") 6004-013H Seat The seat has a jointed attachment on the front edge and can be tipped forward. The seat can also be adjusted lengthways. Release the knobs under the seat and adjust it forwards or backwards to the required position. Lock the setting with the knobs. 6004-014H Fuelling The engine should be run on 87 octane (or hig
Resumen del contenido incluido en la página 20
DRIVING IMPORTANT INFORMATION The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt. Impaired cooling of the engine. Risk of major engine damage. 8009-431 Before starting • Read the safety instructions and information on the location and function of the controls before starting. • Conduct daily maintenance before starting (see “Maintenance Schedule”). 6007-001H Starting the engine 1. Lift up the cutting unit by pul
