Resumen del contenido incluido en la página 1
GRASS COLLECTION
SYSTEM
PEC PEC PEC PEC PECO O O O O
PPPPP
DESIGNED FOR:
MODEL# 37621219 & 37621220
SCAG TURF TIGER SERIES MOWER
OPERATOR’S MANUAL
ASSEMBLY OPERATION MAINTENANCE
MANUAL PART#: Q0344 $4.00 REV: 1
Resumen del contenido incluido en la página 2
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety ------------------------------2 2-11 Blower Cone Installation ----------------11 Safety Alert Symbols----------------------3 2-121 Impeller Blade Removal/Replacement - ------1 Warranty -----------------------------4 2-13 The Length Of Hose Adjustment-----------12 2-14 Upper Hose Installation ----------------12 I INTRODUCTION AND DESCRIPTION - - ------------5 2-15 Lower Hose To Blower Cone Installation------12 1-1 Int
Resumen del contenido incluido en la página 3
SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. WARNING! To avoid serious injury, perform maintenance on the vacuum collector; ONLY AFTER STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP.
Resumen del contenido incluido en la página 4
PECO LIMITED WARRANTY FOR NEW PRODUCTS A. WHAT IS WARRANTED? PECO extends the following warranties to the original purchaser of each new PECO consumer product subject to the following limitations: 1. PRODUCT WARRANTY: Any part of any consumer product, which is defective in material or workmanship as delivered to the purchaser will be repaired or replaced, as PECO elects, without charge for parts or labor, if the defect appears within 12 months from the date of delivery of the product to the orig
Resumen del contenido incluido en la página 5
SECTION I INTRODUCTION AND DESCRIPTION 1-1 Introduction Note: If equipped with a Donaldson air cleaner, unit must be rotated to make clearance for top main frame We are pleased to have you as a PECO customer. Your assembly. collection system has been designed to give you a low To rotate Donaldson air cleaner, loosen bolt on air maintenance, simple, and effective way to collect the cleaner bracket, rotate air cleaner forward as needed for grass clippings from your mower. This manual is clearance
Resumen del contenido incluido en la página 6
2-3 Lift Handle Installation Figure 2-4. The various parts of the handle assembly P#(A0273) must be attached to the container frame. Page 7 shows the orientation and location of the components. Slide the lift handle into the slot in the handle mount bracket P#(B1730) on the grass container. It may be necessary to remove the handle grip P#(J0522) to allow the handle to fit through the slot. Before attaching the handle, hook one end of the spring P#(J0176) into the hole on the underside of the han
Resumen del contenido incluido en la página 7
Lift Handle Assembly Aluminum Grass Container Assembly Aluminum Grass Container With Handle Attached Latch Hook Mechanism Assembly 7
Resumen del contenido incluido en la página 8
Aluminum Grass Container Exploded View (1) C0025 (1) B8113 Box Top (1) C0029 Screen Screen Support (1) C0023 (4) B1668 Box Back & Inlet Clamp Sides (1) A0273 (1) C1184 (1) V1054 (1) A0938 Fill Gage Box Handle Inlet Box/Door Frame (1) J0522 (1) B1730 Handle Grip Handle Mount (1) V1131 Plastic Door (1) J0176 Latch Spring (2) B2526 Linkage Rod (1) B3688 (2) K1422 Upper Door Adjusting Nut Member (1) A0260 Latch Rod (2) K1435 Adjusting Screw (1) K1442 Adjusting Ball Joint (1)C0024 (1) A0738 Box Botto
Resumen del contenido incluido en la página 9
A0675 UNIT ASSY. (1) (1) V1054 A0294 (1) 6” PLASTIC LONG THROTTLE HB0251 INLET KIT FOR (6HP) HARDWARE OR BAG (1) A0060 LONG THROTTLE KIT FOR (5.5HP) (2) J6006 (1) (1) 7” - 8” 6” x 39” A0794 (1) HOSE CLAMPS 12 CU. FT. UPPER 8” x 44” BOX ASSY. HOSE LOWER HOSE (1) A00019 (1) ENGINE MOUNT E6009 ARM ASSY. 8” BLOWER CONE (1) A0923 MAIN FRAME ASSY. (1) (1) A0273 (1) A0416 BOX HANDLE ENGINE/ OUTER ENGINE ASSY. BLOWER/ MOUNT ASSY. BLADE ASSY. A0674 WEIGHT KIT A0664 BOOT KIT (1) (2) (1) (1) B2220 (1) B002
Resumen del contenido incluido en la página 10
2-7 Mount Tube Assembly Installation 2-9 Engine/Blower/Blade Assembly Installation Remove the (4) carriage bolts and (4) nuts from the rear plate. See Figure 2-7a. Remove the mower’s rear plate and secure the outer engine mount assembly P#(A0416) Place the engine/blower/blade assembly onto the engine to the rear of the mower using the existing (4) bolts and mount arm assembly (Figure 2-9). Secure the nuts. See Figure 2-7b. engine/blower/blade assembly to the engine mount arm assembly by using (4
Resumen del contenido incluido en la página 11
2-11 Blower Cone Installation 2-12 Impeller Blade Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially To Remove: First remove the center bolt (#1), washer thread the bolts into each of the two tabs located on the (#2) and spacer (#3) from the taper-lock bushing (#5). blower housing. Place blower cone so the two tabs line up See Figure 2-12. Next remove the (2) 1/4”-20 bolts (#4) with the bolts then tighten completely. See
Resumen del contenido incluido en la página 12
2-16 Lower Hose To Boot Installation 2-13 Length Of Hose Adjustment Take the unattached end of the lower hose and slide it The hoses in steps 2-14 and 2-15 must be cut to fit your over the circular end of the boot. Use the lower hose machine. Follow steps 2-14 and 2-15. Do not cut the clamp to secure the hose to the boot (Figure 2-16). Tip: hoses until you have tried to fit them on your machine. Before securing clamp rotate hose counter-clockwise Remember that the hoses have to be long enough to
Resumen del contenido incluido en la página 13
2-18 Throttle Cable Installation Figure 2-18d. To install the throttle cable kit to the box assembly, align the large end of the slot in the throttle base plate (Figure 2-18a) with the rivets located on the front of the box assembly frame (Figure 2-18b). Place the throttle base plate over the rivets, Slide the throttle cable kit to the right, moving the smaller end of the slot over the rivets. When positioned correctly, the throttle spring plate will snap into place (Figure 2-18c). To remove the
Resumen del contenido incluido en la página 14
A. Stop the forward movement of the mower. SECTION III B. Disengage the mower deck. C. Using the throttle cable slow the engine down to idle. OPERATING INSTRUCTIONS D. Push the dump handle, on the left of the operator, away from the unit. While holding the handle pushed 3-1 General Safety away, move the handle upward. The container door will swing upward and the container will rotate downward. The container will release its contents. Only qualified people familiar with this operator’s manual and
Resumen del contenido incluido en la página 15
Turn any PECO Lawn Vac into a total SECTION V lawn grooming tool with the PECO PARTS AND SERVICE Wand Kit! With your PECO Wand Attachment you will double the ability of your PECO Lawn Vac. 5-1 Parts And Service Information Using the same powerful vacuum/blower that makes your Lawn Vac work so well, you will be PECO collection system owners should record the name able to get to all those hard-to-reach places and telephone number of their Service Center. Your where you needed a rake or broom befor
Resumen del contenido incluido en la página 16
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R4027 Part #: R1053 Part #: R1069 Part #: R4028 Part #: R1057 Part #: R1049 Part #: R1055 Part #: R1054 Part #: R1065 Part #:R4054 Part #:R4015 Part #: R1070 Part #:R1051 Part #:R4008 16
Resumen del contenido incluido en la página 17
17
Resumen del contenido incluido en la página 18
PEC PEC PEC PEC PECO O O O O PPPPP P.O. BOX 1197 ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com
