Manual de instrucciones de Altinex MT108-105

Resumen del contenido incluido en la página 1

MULTI-TASKER
MT108-104 is shown above.
MANUAL PART NUMBER: 400-0178-002
MT108-104/MT108-105
4-IN, 4-OUT STEREO AUDIO LINE
TM
DRIVER CARDS FOR MULTI-TASKER
USER’S GUIDE

Resumen del contenido incluido en la página 2

MULTI-TASKER TABLE OF CONTENTS Page .............. 2 1.1 GENERAL ................................ .................. 2 1.2 INSTALLATION ................................ .......... 2 1.3 CLEANING ................................ ................. 2 1.4 FCC / CE NOTICE ................................ ...... 2 ABOUT YOUR MT108-104/(105) ......

Resumen del contenido incluido en la página 3

MULTI-TASKER interference that may cause undesired PRECAUTIONS / SAFETY WARNINGS 1 operation. Please read this manual carefully before using • This equipment has been tested and found to your MT108-104/(105) Line Driver. Keep this comply with the limits for a Class A digital manual handy for future reference. These safety device, pursuant to Part 15 of the FCC Rules. instructions are to ensure the long life of your These limits are designe

Resumen del contenido incluido en la página 4

MULTI-TASKER ABOUT YOUR MT108-104/(105) 2 TECHNICAL SPECIFICATIONS 3 FEATURES/DESCRIPTION MT108-104/(105) GENERAL 4-in 4-out Stereo Audio Line Driver Inputs 4 Cards The MT108-104/(105) is a Stereo Audio Line Outputs 4 Driver Card designed for use with the Multi- Tasker ™ system. When installed in a Multi- Tasker ™, this card allows the connection of four Compatibility stereo audio sources to four receiving devices, Table 1. MT108-104/(105)

Resumen del contenido incluido en la página 5

MULTI-TASKER DESCRIPTION OF MT108-104/(105) 4 APPLICATION DIAGRAM 5 4 Application 1

Resumen del contenido incluido en la página 6

MULTI-TASKER Application Diagram 2: Internal View of the MT108-104/(105) 5

Resumen del contenido incluido en la página 7

MULTI-TASKER INSTALLING YOUR MT108-104/(105) 6 1. Square brackets “ [ ] ” are part of the command. Step 1. Slide the MT108-104/(105) into an available slot in the Multi-Tasker™ Basic 2. Use uppercase letters for all commands. Enclosure in order to connect to the bus. Make sure that the MT108-104/(105) card fits into place. Secure the card to the Each command consists of three parts: Multi-Tasker™ by tightening the retainer function, card

Resumen del contenido incluido en la página 8

MULTI-TASKER Example: S = save configuration If Outputs 1 and 2 are at volume level 16 and If one MT108-105 card is plugged in slot #2 of outputs 3 and 4 are at level 8, the feedback unit 3: after sending the command [C4S], for slot 4, Send the command [VERC2U3] , and the would be: -Tasker™ Basic Enclosure will return the Vol1=16/16 following feedback: Vol2=16/16 MT108-105 690-0127-007 Vol3=8/16 690-0127-007 = software version Vol4=8/16 M

Resumen del contenido incluido en la página 9

MULTI-TASKER Example: needed for execution. Insert a 200ms delay [WAIT] time after sending this command. If cards 1, 2, and 3 are grouped as group 5 of unit 1, send the command [SEL1G5U1]. Then [ ] send the commands [ + ], and [ - ] to increase Cn = card ID No. (n = slot # from 1 to 19) or decrease the volume for cards 1, 2, and 3 (1-8 for MT100-101 or 1-4 for MT100-106) simultaneously. = Unit ID number ( i = 0 to 9) 5. [SEL] After [CLR

Resumen del contenido incluido en la página 10

MULTI-TASKER = unit number (i = # from 0-9) TROUBLESHOOTING GUIDE 8 Example: We have carefully tested and have found no problems in the supplied MT108-104/(105) ; To group cards #1, 2, and 3 as group 5 of unit however, we would like to offer suggestions for the #1, send the command [WRC1C2C3G5U1]. follow i ng: After executing this command, cards 1, 2, and 3 of unit 1 will be grouped together as group 5. • 8.1 LED IS NOT LIT • 8.2 NO SOUND

Resumen del contenido incluido en la página 11

MULTI-TASKER source is working and there is still 8.4 SOUND LEVEL IS LOW no sound, see Cause 2. Cause 1: The v olume levels are Cause 2: The card output is turned OFF. inappropriate. Solution 1: Turn ON the card output that is Solution 1: Turn up the source volume. If sound used. See RS-232 accessible level is still low, see Solution 2. commands in section 7. If no sound Solution 2: Turn up the destination amplifier is present, see Soluti