Resumen del contenido incluido en la página 1
OWNER'S
MANUAL
MODEL NO.
580.75165!
CRRFTSMRN°
PRESSURE WASHER._
6.5 HORSEPOWER
"_ CUSTOME.
HELPLINE
2200PSI 3GPM
HIGH PRESSURE WASHER
• Assembly
HOURS:
Mon,- Frlo8 a.m. to 5 p.m
• Operation
(CST)
° Customer Responsibilities
CAUTION:
Read and Follow
• Service and Adjustment
all Safety Rules
• Repair Parts
and Instructions
Before Operating
This Equipment
i, i ,m
ii mmlll i,,i, ,=LL, I ,,,,I,,,,,I,,I
SEARS, ROEBUCK and CO., HoffmanEstates, IL 60179 U.S.A.
Pm'tNo.97016Revision 4 (11/14/95)
Resumen del contenido incluido en la página 2
SAFETY RULES TACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, _ CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CON- ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER, • High pressure spray can cause paint chips or other par* TRAINING: ticles to become airborne and fly at high speeds. • Engine exhaust gases contain DEADLY carbon monox- = Always wear eye protection when you use this equipment ide gas. This dangerous gas, if breathed i
Resumen del contenido incluido en la página 3
CONGRATULATIONS on your purchase of a Sears Crafts- PRODUCT SPECiFICATiONS man high pressure washer. It has been designed, engi- Pressure Washer Specifications neered and manufactured to give you the best possible '#UMP"PRESSURE dependability and performance. Adjustable to 2200 psi FLOW RATE _hould you experience any problem you cannot easily 3 9pm =,medy, please contact your nearest Sears Service Cen- DETERGENT MIX Use undiluted dete_ent t.r/Department or call the 1-800 number listed on the fro
Resumen del contenido incluido en la página 4
TABLE 0F CONTENTS SAFETY RULES ............................................................ 2 CUSTOMER RESPONSIBILITIES .......................... 14-16 ( PRODUCT SPECIFICATIONS ...................................... 3 SERVICE AND ADJUSTMENTS .................................. 177 ACCESSORIES AND ATTACHEMENTS ...................... 5 STORAGE .................................................................... 18I CONTENTS OF HARDWARE PACK ............................. 6 TROUBLESHOOTING .........
Resumen del contenido incluido en la página 5
ACCESSORIES AND ATTACHMENTS These accessories and attachments were available when the high pressure washer was purchased. They are also vailable at most Sears retail outlets and service centers. Most Sears stores can order these items for you when you ,_rovide the model number of your high pressure washer. Some of these accessories may not apply to your pressure asher. @ i i i - i L_ -L=_ 1 f r ! 1 I 1 i J @ J FLOOR/SIDING ROTATING BRUSH UTILITY BRUSH KIT ELECTRIC TURBO 18"STAINLESS ANGLE EXTENS
Resumen del contenido incluido en la página 6
CONTENTS OF HARDWARE PACK Parts packed separately in carton Parts Carton ( Owner's Manual Guide Handle Assembly (packed in flat carton) Main Unit Parts packed in Parts Carton Detergent Pickup Tube and Filter (2) Support Legs Motor Oil Wheels Nozzle Cleaner Vinyl Cap High Pressure Kit Hose Oil Fill Cap/Breather Quick-Connect Adjustable Nozzle Wire Support (2) Push Nuts- 1/2" Parts packed in carton shown full size (2) Axle Pins (2) Washers - #10 (2) Washers - M12 (2) JAM Nuts- 5/8" lllI!II!fl!lll
Resumen del contenido incluido en la página 7
ASSEMBLY Read these instructions and Operator's Manual in its en- HOW TO SET UP YOUR PRESSURE WASHER tirety before you attempt to assemble or operate your new TO INSTALL THE WHEEL KIT high pressure washer. Your high pressure washer has, for he most part, been assembled at the factory, except those Installing the wheel kit requires the tools listed, the guide )arts left unassembled. Before you can operate your new handle and items included in the parts carton. high pressure washer, you must assem
Resumen del contenido incluido en la página 8
ASSEMBLY Screen in water inlet for cleanliness and inspect Inlet • Attach wire support to two lower holes in guide handle Screen on female connector. Reattach male connector with #10 self-drilling screws and # 10 fiat washers (Fig. to water inlet and attach female connector to garden 3). The hose minder should be to the left and gun holder hose. to the ri_ht. Be sure loop of support is pointing upward. Place vmyt cap onto gun holder. • Unravel high pressure hose, remove protective cap from end o
Resumen del contenido incluido en la página 9
OPERATION KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER. Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. DETERGENT PICKUP TUBE OIL FILL OPENING AND FILTER WIRE SUPPORT FOR GUN AND HOSE STORAGE MUFFLER ENGINE ON-OFF HIGH PRESSURE OUTLET STARTER GUIDE HANDLE GUN AND WAND ASSEMBLY PUMP PRESSURE REGULATOR
Resumen del contenido incluido en la página 10
OPERATION HOW TO USE YOUR WASHER IF YOU HAVE ANY PROBLEMS OPERATING YOUR PRESSURE WASHER, PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-222-3136. STOPPING YOUR PRESSURE WASHER . First, move engine RUN/STOP switch to "STOP" posi- tion (Fig, 9). ADJUSTAB_ .=NOZZLE OPTIONAL TURBO NOZTLE FIG. 10 FIG. 11 With the adjustable nozzle you can adjust the spray pattern to be either high pressure or low pressure. You can also adjust the spray so it is concentrated in a stream pattern or expanded into a
Resumen del contenido incluido en la página 11
OPERATION APPLIYiNG DETERGENT WITH ADJUSTABLE o Hbok up water supply (Fig. 16) and turn ON water. NOZZLE o NOTE: Be sure female quick-connect is installed prop- IMPORTANT: USE SOAPS DESIGNED SPECIFICALLY erly onto male connector. --OR PRESSURE WASHERS. HOUSEHOLD DETER- 3ENTS COULD DAMAGE THE PUMP. IMPORTANT: YOU MUST A'I-I'ACH ALL HOSES BE- QUICK-CONNECT FORE YOU START THE ENGINE. STARTING THE EN- GINE WITHOUT ALL THE HOSES CONNECTED WILL DAMAGE THE PUMP. WATER SUPPLY Pressure washers are useful
Resumen del contenido incluido en la página 12
OPERATION ADD ENGINE OIL: • Clean area around fuel fill cap, remove cap. * Place pressure washer on a level surface and remove ,, Add =UNLEADED" regular gasoline, slowly, to fuel I tank. one of the yellow Oil FillCaps (Fig, 17) and add engine oil from the enclosed bottle unttl level is at point of • Install fuel cap and wipe up any spilled gasoline. overflowing. Check engine oil level before starting TO TURN ON WASHER each time thereafter. If oit level is below point of overflowing, fill to prop
Resumen del contenido incluido en la página 13
OPERATION SENSING LOW PRESSURE i If the system senses tow oil pressure during operation, the ( engine shuts down. As the system shuts down, the low oil light comes ON. However, once the engine has stopped rotating, this light will go OFF. See Fig. 21 for schematic. _E_;SURE _ FGRN_-I Oi I [ L_;D L L _ - i _ HO_"JLg _tlG GRN RUN 0 sP FIG. 19 .LuG J _. CNO. )G_£1"(())_ FIG. 21 RESTARTING If you try to restart the engine within 10 seconds after it shuts down, the engine may NOT start. The system ne
Resumen del contenido incluido en la página 14
CUSTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE RLL INDATESASYOUCOMPLETE REGULARSERVICE HOURLY OPERATING INTERVAL SERVICE DATES Every25 Every50 Every 100 Before Hoursor Hoursor Hoursor MAINTENANCE TASK EachUse Yearly Yeady Yeady PRESSURE WASHER Check/cleaninletfilter andscreen XV Checkhighpressurehose. X Checkdetergenthose. X Checkgunand wandfor leaks. X X Checkpumpoil. • Purgepumpof airandcon_nirnents _ X , ENGINE Check oillevel. X Changeengine oil. • X* Retorquehead bolts. X Serviceair cleaner.
Resumen del contenido incluido en la página 15
CUSTOMER RESPONSIBILITIES CHANGING ENGINE OIL Purge Pump of Air and Contaniments: o Change oil after first 8 hours of operation. Change oil To remove the air from the pump, follow these steps: every 50 hours thereafter, tf you are using your pres- , Set up the pressure washer as described in the AS- sure washer under extremely dirty or dusty conditions, SEMBLY section and connect the water supply. or in extremely hot weather, change oil more often. Remove the nozzle attachment from the gun. • Ch
Resumen del contenido incluido en la página 16
CUSTOMER RESPONSIBILITES SERVICE AIR CLEANER CLEAN/REPLACE SPARK PLUG Change the spark plug every 100 hours of operation or ABk COMPLETE AIR CLEANER SYSTEM INSTALLED once each year, whichever comes first. This will help your ON THE ENGINE. THIS COULD RESULT IN PRE- A CAUTION: NEVER RUN THIS UNIT WITHOUTTHE engine to start easier and run better. Replace with Cham- MATURE WEAR TO THE ENGINE. pion RC12YC or equivalent type spark plug. Set spark plug gap 0+030 inch (0.76mm). Your engine will not run
Resumen del contenido incluido en la página 17
SERVICE AND ADJUSTMENTS ENGINE SPEED A CAUTION: ENGINE SPEED WAS PROPERLY AD- JUSTED AT THE FACTORY AND SHOULD RE- QUIRE NO ADDITIONAL ADJUSTMENT. DO NOT ATTEMPT TO CHANGE ENGINE SPEED. IF YOU BELIEVE THE ENGINE IS RUNNING TOO FAST OR TOO SLOW, TAKE YOUR PRESSURE WASHERTO SEARS AUTHORIZED SERVICE CENTER FOR RE- FEELER ALLEN PAIR AND ADJUSTMENT, CHANGING ENGINE GAUGE GOVERNED SPEED WILL VOID ENGINE WAR- RANTY. ',LOOSEN JAM NUT Your pressure washer runs at a constant speed. This constant operating
Resumen del contenido incluido en la página 18
SERVICE AND ADJUSTMENTS o Remove additional debris by back flushing water sup- • Test the pressure washer by operating with nozzle in ply through wand (Fig. 30). Back flush between 30 to the high and in the tow position. 60 seconds. Turn wand to stream spray and move i nozzle from low to high while flushing. <3;a , Reinstall nozzle into the wand. DO NOT overtighten. I Reconnect the wand to the gun o Reconnect the water supply, tum on the water, and start the engine. FIG. 30 STORAGE NOTE: As alwa
Resumen del contenido incluido en la página 19
TROUBLESHOOTING CORRECTION CAUSE PROBLEM 1. Pullnozzle backwardfor high 1. Nozzle intow pressuremode. Pumphas following problems: pressuremode, failure to producepressure,erratic 2. Adjustregulatorto desiredsetting. pressure,chattering,lossof pressure, 2. Lowregulatorpressure lowwater volume. 3. Water inletis blocked. 3. Clear inlet 4. Inadequate water supply 4, Provideadequatewater flow, 5. 5. Straighteninlethose, patchleak. Inlet hoseis kinkedor leaking 6, 6. Check andclean inlethosestrainer.
Resumen del contenido incluido en la página 20
Z o 0 "U (/} J 9" m m u) U) C m 60 (n rn ::0 01 01 ,,.aw o_ (.11 m "4 Cn
