Résumé du contenu de la page N° 1
®
ViewSonic
N2690w
LCD TV
- 使用手冊
- User Guide
0
Model No. : VS12276-1G
Résumé du contenu de la page N° 2
Contents Important Safety Instructions........................................................................... 1 Copyright Information ...................................................................................... 2 Product Registration........................................................................................ 2 Antenna Installation Instructions ..................................................................... 3 Cleaning the LCD TV .............................
Résumé du contenu de la page N° 3
Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the LCD TV” in this guide for further instructions. 7. Do not block any v
Résumé du contenu de la page N° 4
23. For the battery: ① If batteries are needed for the equipment, please ensure the correct polarities of the batteries (+/-) while installing. ② The waste batteries shall be properly disposed of, and never burn it in a fire. ③ Never expose the batteries (packaged batteries or the batteries installed in the equipment) to excessive heat, for example, the sunlight or fire and the like. Copyright Information ® Copyright © ViewSonic Corporation, All rights reserved. ViewSon
Résumé du contenu de la page N° 5
Antenna Installation Instructions 1. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges, Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to grou
Résumé du contenu de la page N° 6
Cleaning the LCD TV • Make sure the LCD TV is turned off. • Never spray or pour any liquid directly onto the screen or case. To clean the screen: 1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles. 2. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen. To clean the case: 1. Use a soft, dry cloth. 2. If still not clean, apply a small amount of
Résumé du contenu de la page N° 7
Getting Started ® Congratulations on your purchase of a ViewSonic LCD TV. Important! Save the original box and all packing material for future shipping needs. Package Contents Your LCD TV package includes: • LCD TV • Remote Control with batteries • Power Cord • RF Cable • Warranty Card* • ViewSonic User Guide Mounting ViewSonic LCD TV to the wall The LCD TV can be used in a free standing position or wall-mounted. Before installing the product to the wall, please cons
Résumé du contenu de la page N° 8
Place the TV on a solid surface 1. Ensure that the TV is placed in a position to allow free flow of air. Do not cover the ventilation openings on the back cover. 2. Leave at least 15cm around the TV set. Otherwise, air-circulation may be inadequate and cause overheating, which may cause a fire or damage to the TV set. 3. Never place the TV set in hot, oily humid or excessively dusty places. 4. To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be
Résumé du contenu de la page N° 9
Turn the TV on & Off 1. Power On : Press the power button on the remote control or key to pad to turn it on. 2. Power Off : Press the power button on the remote control or key to pad to turn it on. 3. LED Indicator Lights up in Blue : the TV is turned on. Lights up in red : the TV is in standby mode. Overview the LCD TV & Connection The Front of the Screen Introduction Power: Turn the power on from standby mode or turn the power off return to the standby mode.
Résumé du contenu de la page N° 10
Signal Source Interface from Rear View You can connect numerous items of source equipment to your TV. The figure below shows you how to connect these. Place the TV on a table with the LCD screen facing down to facilitate easy connection with the external equipment. Please take precautionary measures to avoid damaging the LCD screen. Antenna Input: Connect the antenna or CATV cable Note: CATV cable to this 75 Ω coaxial cable input AV/S-Video Input: Connect the Video s
Résumé du contenu de la page N° 11
Signal Source Interface from Side View HDMI: HDMI (High-Definition Multimedia Interface) can be used to connect the HDMI signal cable to the DVD player and other devices. Headphone jack: The user can use headphones by inserting the plug into the headphone jack. There are several source devices that can connect to your TV. Here is how to connect various devices. Tips: When connecting the external equipment with the TV, please ensure that the TV power is turned off. Wh
Résumé du contenu de la page N° 12
To Use Remote Control Enter Sleep Press the button to confirm With this key you can selection. set a time period after which the TV should POWER switch itself to standby. Press to turn on/off. Press the key repeatedly to select the HDMI number of minutes. To select HDMI input. The counter runs from 15, 30, 45, 60, 90, 120 YPbPr minutes. To select YpbPr/PC input. (PC mode did not support this function) Recall To display the previously
Résumé du contenu de la page N° 13
Remote Control Battery Installation Follow the steps below to insert batteries. 1. Open the remote control’s rear battery compartment cover. 2. Insert two AAA (1.5v) batteries. Ensure that the positive and negative ends match as indicated on the bottom of the battery compartment. CAUTION 1. Only use the specified AAA batteries. 2. Do not mix new and old batteries. This may result in cracking or leakage, which may pose a risk of fire or lead to personal injury 3. Insert
Résumé du contenu de la page N° 14
To Use the OSD Menu All the functions for the LCD TV are control either by the remote control or the control button on the front control screen at bottom of right side. 1. Press the Menu button to display or exit the OSD main menu. 2. Use the Up or Down buttons to select the function to be adjusted. The function where the cursor is located is the selected one. 3. Use the Left or Right buttons to enter into the submenu, or to enable or adjust the selected function. The function w
Résumé du contenu de la page N° 15
Picture Setting 1. Picture adjustment: This option provides 4 choices: Personal, Colorful, Standard, and Soft. 2. Adjustable Brightness and Contrast range is from 0~100. Screen brightness can be set by adjusting the Brightness or Contrast. 3. Saturation: Adjustable range from 0~100. Adjust this option to change the color intensity on the screen. （Not support for VGA,HDMI mode） 4. Sharpness: Adjustment picture sharpness, range is from 0 to 10. （Not support for PC, HDMI mode. ）
Résumé du contenu de la page N° 16
Sound Setting 1. Sound adjustment: Designed for different sound output modes, including dialogue, music, theatre modes. The bass and treble cannot be adjusted in the Preset mode. According to your preferences, the sound output mode can be set by adjusting the bass, treble, and balance in the Personal mode. 2. Base and Treble: Adjustable ranges are from -10 ～10. 3. Balance: Adjustable ranges are from -10 ～10. Right channel sound fades out as adjusting from 0 to -10 and the left c
Résumé du contenu de la page N° 17
Advance Settings （Not applicable for PC mode） 1. NR: Off, Weak, Middle or Strong. Choose to clear serious noise problems from the screen. Please refer to the actual screen when making your selection. It is recommended not to change settings when noise problems are minor. 2. High contrast: To enhance the color saturation and color effect. 3. Aspect ratio: Use wide, Normal, 16:9 Zoom-Up modes to select the screen ratio. 4. Memory Recall: To reset the Advance Settings back to the factory
Résumé du contenu de la page N° 18
TV Setting （Available only under TV mode） 1. Auto Scan: To scan the channel saver automatically. 2. Manual search: Use left/right buttons to the display the following OSD Menu. (1) Channel: To display current channel number. (2) Channel’s name: To display current channel’s name. (3) Frequency: To display current channel frequency Manual fine-tuning method: Press the Up/Down key to select the frequency option. The option will turn yellow. Then press the Left/Right key to adju
Résumé du contenu de la page N° 19
(7) AFC ：can be set to On or Off. If set to On, the TV will automatically detect TV signals, and automatically adjust to the correct position in a certain frequency range when the signal offset occurs. 。 (8) Save: Save each setting for manual tuning. 。 3. Channel list: Press the Left/Right button to enter the submenu; see the figure below. You can edit the channel list according to the instructions at the bottom of the menu.
Résumé du contenu de la page N° 20
System Settings 1 ．OSD Language ：Select the OSD language among Simplified Chinese and English. 2. OSD Duration: To adjust the duration of the Menu on the screen. 3 ．Sleep Timer ：You can set a timer to enter standby status for the unit. (Not support for PC mode) 4. OSD Halftone: Adjustable range from 0 ～15. To adjust the menu transparency. 5. Recall: To reset the System settings back to the factory default settings. 6. Reset: To reset the settings back to the factory defaul
