Instruction d'utilisation Bosch Appliances 20

Résumé du contenu de la page N° 1

TCB4 Upgrade Kit for LBB 3500/00, /10 and /30
LBB 3500/00 and LBB 3500/10
LBB 3500/30
SS ecurit ecurit y Syst y Syst ems ems
Installation Instruction
en LBB 3519/20

Résumé du contenu de la page N° 2

Résumé du contenu de la page N° 3

Digital Congress Network | TCB 4 Upgrade Kit LBB 3519/20 | Chapter 1. Upgrade Kit LBB 3519/20 en | 3 Chapter 1. Upgrade Kit LBB 3519/20 LBB 3500/xx Introduction The upgrade kit LBB 3519/20 is intended for upgrading of the following DCN Central TCB 2 or 3 Control Units: • LBB 3500/00 (D) • LBB 3500/10 (D) LBB 3500/xx (with upgrade) • LBB 3500/30 (D) The upgrade kit LBB 3519/20 (Trunk Communication Board (TCB 4)) once installed in the Central Control Units provides the C

Résumé du contenu de la page N° 4

Digital Congress Network | TCB 4 Upgrade Kit LBB 3519/20 | Chapter 1. Upgrade Kit LBB 3519/20 en | 4 Installation procedure 1.1 Before you Begin 1. Remove the top-cover from the CCU. WARNING: Before performing any of the procedures described in this 2. Locate the TCB (version 2 or 3). For location of the TCB see Fig 1-1. document that require you to remove the top-cover of the CCU, NOTE: For Multi-CCUs type LBB 3500/30 carefully remove the ‘Multi-CCU’

Résumé du contenu de la page N° 5

Digital Congress Network | TCB 4 Upgrade Kit LBB 3519/20 | Chapter 1. Upgrade Kit LBB 3519/20 en | 5 Connection to I/O board 9-pole D-type connector(s) Ribbon cabling Port 1 Port 2 Trunk Communication Board TCB4 DIP-switch S14 DIP-switch S9 6 x securing screws Connection to I/O board FIGURE 1-2 Internal view of CCU after upgrade Bosch Security Systems | April 03 | 3922 988 97112 en

Résumé du contenu de la page N° 6

Digital Congress Network | TCB 4 Upgrade Kit LBB 3519/20 | Chapter 2. Trunk Communication Board (TCB4) en | 6 DIP-switch S14 Chapter 2. Trunk Communication Board (TCB4) TCB 4 X14 location Fig. 1-2 87 6 5 4 3 2 1 1 2 Key to symbols (fig.2-1) : 13 2 S14 ON 87654321 S14 OFF See Table 3.1 and 3-2 1 Jumper X14 (see Table 2.2) ON ON 1 X1481 2 S14 DIP-switches 1 - 8 (see Chapter 3) ) 15 3 S10 Push-button switch to reset the Central Control Unit during servicing. Port 2 S10 S10 3 X17a X17b 4

Résumé du contenu de la page N° 7

Digital Congress Network | TCB 4 Upgrade Kit LBB 3519/20 | Chapter 2. Trunk Communication Board (TCB4) en | 7 2.4 S9 DIP-Switch settings 2.5 Jumper settings See fig. 2-1 for location, and Table 2.1 for functionality of the DIP-switches. See fig. 2-1 for location, and Table 2-2 for functionality of the jumpers. Table 2.1 : S9 DIP-switch settings Table 2.2 : Jumper settings TCB4 Default Function TCB4 X13 1 & 2 Jumpered to provide SRAM Battery back-up SW 1 ON

Résumé du contenu de la page N° 8

Digital Congress Network | TCB 4 Upgrade Kit LBB 3519/20 | Chapter 3. CCU Protocol and Serial Port settings en | 8 NOTE: It is possible to select ‘Full’ protocol on both Port 1 and Port 2. However this is NOT Chapter 3. CCU Protocol and Serial Port settings recommended due to processing power and memory limitations. For location of DIP-switches see fig. 2-1 3.1 LBB 3500/xx (TCB 4) - Port 1 : DCN Control PC Port 2 : Camera Control In

Résumé du contenu de la page N° 9

Digital Congress Network | TCB 4 Upgrade Kit LBB 3519/20 | Chapter 3. CCU Protocol and Serial Port settings en | 9 Bosch Security Systems | April 03 | 3922 988 97112 en

Résumé du contenu de la page N° 10

For more information please visit www.boschsecuritysystems.com © 2003 Bosch Security Systems B.V. Data subject to change without notice April 03 | 3922 988 97112 en