Résumé du contenu de la page N° 1
I can see and
hear you
INTERFACE BOARD
KIT
Ramsey Electronics Model No. IB1
Ever want to spy on a friend or an enemy without them knowing
it? Well now you can with the IB-1. It is small enough that it can
easily be hidden, yet it picks up audio as well as video! The
Interface board picks up infra-red light, allowing it to be used at
night or in dark places.
• Quick connection to a TV or VCR
• Runs from a 12 to 15 volt power supply
• Great for watching the kids outside while
Résumé du contenu de la page N° 2
RAMSEY TRANSMITTER KITS • FM10A, FM25B FM Stereo Transmitters • TV6, Television Transmitter • MR6, Model Rocket Tracking Transmitter RAMSEY RECEIVER KITS • FR1 FM Broadcast Receiver • AR1 Aircraft Band Receiver • SR2 Shortwave Receiver • AA7 Active Antenna • SC1 Shortwave Converter RAMSEY HOBBY KITS • SG7 Personal Speed Radar • SS70A Speech Scrambler • TT1 Telephone Recorder • SP1 Speak
Résumé du contenu de la page N° 3
Ramsey Publication No. MIB1 Price $5.00 KIT ASSEMBLY AND INSTRUCTION MANUAL FOR INTERFACE BOARD KIT TABLE OF CONTENTS Introduction to the IB1 ................... 4 How It Works ................................. 4 Kit Building Tips ............................. 4 Parts list ......................................... 5 IB1 Placement Diagram ................ 6 IB1 Schematic Diagram ................. 6 IB1 Assembly Instructions ............. 8 Set-Up ................................
Résumé du contenu de la page N° 4
Introduction: It is now possible to monitor what is happening at night as well as during the daylight hours with the Interface board kit and a camera. By virtue of infrared LEDs for night vision and a microphone attached to an amplifier circuit, you can use it to spy on someone or as a means of added security. The Interface board connects directly to your choice of small video cameras and has a video and an audio output which can be plugged into a VCR or a TV (if your TV has audio and vid
Résumé du contenu de la page N° 5
IB1 Parts List: It is a good idea to check off the components in the boxes provided and to separate them as you go along. This will save hunting for specific components later. RESISTORS ❒ 2 470 ohm resistors [yellow-violet -brown] (R8, R9) ❒ 2 1K ohm resistors [brown-black-red] (R1,R4) ❒ 3 10K ohm resistors [brown-black-orange] (R2, R3, R7) ❒ 2 22K ohms resistors [red-red-orange] (R5, R6) CAPACITORS ❒ 1 .1uF capacitor (C4) ❒ 5 10uF electrolytic capaci
Résumé du contenu de la page N° 6
IB-1 • 6
Résumé du contenu de la page N° 7
CONSTRUCTION OF THE IB1 INTERFACE BOARD KIT ❒ 1. Install J2 and J3, the RCA style audio and video jacks, on the PC board. These require some heat for the solder to flow so take your time. ❒ 2. Install J1, the power jack. ❒ 3. Install MK1, the microphone. If you are looking at the bottom of the microphone the two pins should be on the top and side by side. The pin on the left is positive and goes to the inside of the board.The pin on the right is negative and goes to the outside of the bo
Résumé du contenu de la page N° 8
❒ 13. Connect your camera. Follow the wiring diagram on the paperwork enclosed with your camera. OPTIONAL If you are planning on using the Interface board at night or in dark areas you will want to install R10 and R11 along with infrared LEDs. The brightness desired can be changed by using more or less IR LEDs. The circuit is capable of supporting up to 6 LEDs. With each LED change, R10 and R11 will also change. Each LED connected to R10 (hole E) must be in series and each LED connected
Résumé du contenu de la page N° 9
SET-UP: The IB1 is designed to be powered by an external power supply using jack J1. A 12 to 15 volt regulated DC supply is recommended, with the “center” pin of the connector being the positive or the (+) connection. 1. Connect a suitable power supply to the IB1 board. 2. Connect the video output of the IB1 to the video input of your TV or VCR. 3. Connect the audio output of the IB1 to the audio input of your TV or VCR
Résumé du contenu de la page N° 10
CONCEALMENT IDEAS: There are many places that the Interface board and a small CCD camera (check the Ramsey catalog or website at www.ramseykits.com) can be hidden because of their size and maneuverability. The best place for you depends on your application and what type of setting it is to be used in. The Interface board and a camera could be used to watch the children, for security outside as well as inside, or to capture the 10 thousand dollar home video. Here are a few ideas that we
Résumé du contenu de la page N° 11
The Ramsey Kit Warranty Please read carefully BEFORE calling or writing in about your kit. Most problems can be solved without contacting the factory. Notice that this is not a "fine print" warranty. We want you to understand your rights and ours too! All Ramsey kits will work if assembled properly. The very fact that your kit includes this new manual is your assurance that a team of knowledgeable people have field-tested several "copies" of this kit straight from the Ramsey Inventory.
Résumé du contenu de la page N° 12
Interface board Kit Quick Reference Page Guide Introduction to the IB1 ...................... 4 How It Works .................................... 4 Kit Building Tips ............................... 4 Parts list ........................................... 5 IB1 Placement Diagram ................... 6 IB1 Schematic Diagram ................... 6 IB1 Assembly Instructions ................ 8 Set-Up .............................................. 9 Troubleshooting ......................
