Instruction d'utilisation Conair GB

Instruction d'utilisation pour le dispositif Conair GB

Dispositif: Conair GB
Catégorie: Mixeur
Fabricant: Conair
Dimension: 3.94 MB
Date d'addition: 10/9/2014
Nombre des pages: 119
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Conair GB. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Conair GB.

Pour votre confort

Si regarder l'instruction Conair GB directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Conair GB en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Conair GB sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Conair GB Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 119 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Conair GB - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Conair GB. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

Gravimetric
Blenders
GB and WSB models
with 12-component control
Installation
Maintenance
Operation
Troubleshooting
The Conair Group, Inc.
Instant Access
One Conair Drive
Parts and Service
Pittsburgh, PA 15202
(800) 458-1960
Phone: (412) 312-6000
(814) 437-6861 Fax: (412)-312-6320
www.conairnet.com
UGB007/1103

Résumé du contenu de la page N° 2

It’s a good idea to record the model and serial number(s) of Please record your your equipment and the date you received it in the User equipment’s model and Guide. Our service department uses this information, along serial number(s) and with the manual number, to provide help for the specific the date you received it equipment you installed. in the spaces provided. Please keep this User Guide and all manuals, engineering prints and parts lists together for documentation of your equipment. Date:

Résumé du contenu de la page N° 3

The Conair Group Inc. TWELVE COMPONENT SOFTWARE GB and WSB Model Blenders TABLE of CONTENTS GETTING STARTED, READ THIS PAGE ................ Page 3 SAFETY HAZARDS ................................. Page 4 DISCLAIMERS .................................... Page 5 PART I - ASSEMBLY Assembly and Installation Instructions ......... Page 6 Wiring Considerations .....................

Résumé du contenu de la page N° 4

GETTING STARTED, READ THIS PAGE. THE NEXT 13 PAGES OF THIS MANUAL WILL GUIDE YOU, STEP BY STEP, TO A SUCCESSFUL STARTUP. IT WON'T TAKE LONG; SO.... PLEASE, DON'T SKIP AHEAD. HERE ARE THE STEPS YOU WILL FOLLOW. SAFETY HAZARDS: TWO HAZARDS exist on this unit: MIX BLADES and Page 4 SLIDE VALVES. Read this short sensible page so no one gets hurt. ASSEMBLY INSTRUCTIONS: Very

Résumé du contenu de la page N° 5

SAFETY HAZARDS +-----------------------------------------------------------+ ¦ MIX BLADES ¦ ¦ ¦ ¦ Mix blades are driven with substantial torque. ¦ ¦ ¦ ¦ NEVER place your hand in the mix chamber ¦ ¦ while blades are t

Résumé du contenu de la page N° 6

DISCLAIMERS PRODUCTION of FAULTY PRODUCT Processing conditions and materials vary widely from customer to customer and from product to product. It is IMPOSSIBLE for us to anticipate ALL processing conditions and requirements, or to be certain that our equipment will perform properly in all instances. You, the customer, must observe and verify the performance level of our equipment in your plant as part of your overal

Résumé du contenu de la page N° 7

+--------------------------------------------------------------------+ ¦ PART I - ASSEMBLY ¦ +--------------------------------------------------------------------+ ASSEMBLY and INSTALLATION INSTRUCTIONS CAUTION: LOAD CELLS ARE EASILY DAMAGED. If the FRAME is dropped from TWO FEET, the load cells WILL BE DAMAGED. THE WARRANTY DOES NOT COVER DAMAGED LOAD CELL

Résumé du contenu de la page N° 8

2. Slide the WEIGH BIN into position. It rests behind the clear hinged access window. Install with the air cylinder toward you. If bin is already in place, remove any shipping materials, packing tape or string. 3. Hang the Color and Additive Feeders: a. Lift side latches and fully extend slide assembly. Remove the hopper. Leave slide extended. b. Tilting the entire slide assembly, motor end up, insert one cor

Résumé du contenu de la page N° 9

WIRING CONSIDERATIONS The wiring of your blender is very important to its proper operation. Electronics are very susceptible to voltage spikes and static charges, both of which are very common in plastics factories. To MINIMIZE these things, consider the following. 1. The power supply should be solid; a strong supply, not limited by a "just adequate" control transformer. A source of voltage that comes from a large

Résumé du contenu de la page N° 10

CHECK OUT PROCEDURE As you go through this procedure, if WHAT SHOULD HAPPEN, doesn't happen, see next section, DIAGNOSTICS, for what to check. NOTE: 100/200 series models (3K load cells), display all weights in 1/10 grams ( x.x). 400/900/1800 series models (10K load cells) display weights in FULL grams, NO decimal point. On this page we show all weights with NO decimal point. Start with NO MATERIAL

Résumé du contenu de la page N° 11

LED # 2 will light. Press "2" repeatedly to observe operation. REPEAT THIS SEQUENCE for each dispense valve on your WEIGH SCALE BLENDER. Up to 12 outputs are possible numbered 1 through 9, A, B, and C. Only those connected to devices will operate. AT THIS POINT: NOTE which component NUMBER is assigned to each hopper.

Résumé du contenu de la page N° 12

DIAGNOSTICS - for the CHECK OUT PROCEDURE If display fails to come on at all: check for power at outlet. Check the 1/2 amp panel front fuse. If first display says ( FOUR ), then this is NOT the correct manual for this software. Obtain and use a FOUR software manual. Possible model numbers are: GBM, 140, 14R, 220, 240, 24R, 420, 440, 44R, 940, 184. If model number is not c

Résumé du contenu de la page N° 13

SELECTING CORRECT MODEL Controllers are programmed to control all sizes of Autoweigh Blenders. The MODEL number that your unit is set for will be displayed during the start up sequence every time power is turned on. The possible models are: MODEL BATCH WT valves WEIGH BIN LOAD CELL (GRAMS) DIMENSIONS RATING GBM 400 4 5 x 5 x 5 high 1

Résumé du contenu de la page N° 14

+--------------------------------------------------------------------+ ¦ PART II - OPERATION ¦ +--------------------------------------------------------------------+ LOAD CELL CALIBRATION NOTE: Displays shown here are in full grams. 100 and 200 series models are in 1/10 grams, with a decimal. If your load cells already display a weight close to zero, plus or minus 1

Résumé du contenu de la page N° 15

TURNING ON OUTPUTS - MATERIAL TYPES This controller can control up to TWELVE (12) components; 1 through 9 and A, B, and C. You must "TURN ON" the COMPONENT outputs that you are going to use. Components that are TURNED OFF are not part of ANY routines. A component becomes TURNED ON when it is set to a MATERIAL TYPE. Material TYPES are REGRIND, NATURAL, and ADDITIVE. The AUTOWEIGH BLENDER handles each TYPE DIFFERENTLY. Settings hav

Résumé du contenu de la page N° 16

ADDITIVE (PERCENT OF ALL NATURALS) Components designated ADDITIVE will be added as a percentage of all the NATURALS added together. For example: If component 5 is an ADDITIVE at 5 percent, Then the above example now looks like this: component 1, REGRIND, SET=20.0, 20 percent, component 2, NATURAL, SET= 10, 15.2 percent, component 3, NATURAL, SET= 40, 61.0 percent, component 4, ADDITIVE, SET=05.0,

Résumé du contenu de la page N° 17

SET MATERIAL TYPES The Keystroke sequence to set TYPES is: Press: * Display will say: (PASSWORD) Press: 22222 Display will say: (P x) Press: * Display will say: (INSTR --) Press: 14 Display will say: (1TY= OFF) The "1" is the component (device) number. This is component 1. It will control Hopper 1. Press: CE repeatedly to select one of the

Résumé du contenu de la page N° 18

RATE CALIBRATION YOU DON'T HAVE TO DO THIS. Software is set to expect STANDARD hardware. If a device meters at a much lower feed rate then expected, the software will take 10 to 20 cycles to fully adjust. During this time cycles will take longer. An example of this is a system using a 1/2" auger instead of 1". If you don't mind letting the system SELF ADJUST, or your hardware is STANDARD, then:

Résumé du contenu de la page N° 19

ENTERING SETTINGS Press: SET Display will say (1 R xx.x) (Regrind) or (1 N xxx) (Natural) or (1 A xx.x) (Additive) 1 is Component number. R,N,A is Type. xx.x is Setting. Enter a 3 digit setting: Reg

Résumé du contenu de la page N° 20

SELECTED MODELS - SPECIAL INSTRUCTIONS This section relates SPECIAL information about a few selected models. MICRO PULSE Micro Pulse valves are available on models: GB/WSB GBM (MICRO Blender) with micro pulse valves. GB/WSB 122 with optional MICRO PULSE valves. GB/WSB 131 with optional MICRO PULSE valves. GB/WSB 140 with optional MICRO PULSE valves.


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Conair GB/ WSB Manuel d'utilisation Mixeur 9
2 Conair RB70 Manuel d'utilisation Mixeur 2
3 Conair WSB Manuel d'utilisation Mixeur 6
4 Craftsman 875.50242 Manuel d'utilisation Mixeur 0
5 Sony DHG-HDD500 Manuel d'utilisation Mixeur 3
6 Sony DHG-HDD250 Manuel d'utilisation Mixeur 1
7 Philips Food Processor HR7740 Manuel d'utilisation Mixeur 43
8 Philips hr 7745 Manuel d'utilisation Mixeur 43
9 Philips HR1370 Manuel d'utilisation Mixeur 9
10 Philips AVENT SCF860/20 Manuel d'utilisation Mixeur 12
11 Philips HR1721 Manuel d'utilisation Mixeur 3
12 Philips HR1724 Manuel d'utilisation Mixeur 0
13 Philips HR1372 Manuel d'utilisation Mixeur 39
14 Philips HR1720 Manuel d'utilisation Mixeur 2
15 Philips HR1727 Manuel d'utilisation Mixeur 1