Instruction d'utilisation Hobart ML-134170

Résumé du contenu de la page N° 1

HCM450 Cutter Mixer
HCM450 CUTTER MIXER
MODEL
HCM450 ML-134170
ML-134172
ML-134207
ML-134208
ML-134209
ML-136137
ML-136138
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
F34772 Rev. B (May 2007)

Résumé du contenu de la page N° 2

Installation, Operation and Care of Model HCM450 Cutter Mixer SAVE THESE INSTRUCTIONS GENERAL The HCM450 Cutter Mixer cuts, mixes or blends foods quickly and effi ciently. A transparent lid allows the operator to inspect the product during the mix-cut-blend process. The unit operates continuously, momentarily or with a timer control which shutsoff the machine automatically after the set time has elapsed. The HCM450 bowl has a liquid capacity of 45 quarts. The motor on HCM450 is rated 5 HP, 1

Résumé du contenu de la page N° 3

UNPACKING Immediately after unpacking, check for possible shipping damage. If the cutter mixer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, verify that the electrical service agrees with the specifi cations on the machine data plate located on the frame behind the control box. ASSEMBLY Remove the cutter mixer from the skid and install rubber feet as follows: Apply a bead of silicon sealant (not provided) around

Résumé du contenu de la page N° 4

ASSEMBLING BOWL SEAL AND ATTACHMENTS Refer to the handbook accompanying the cutter mixer for recipe guidelines and advice regarding the appropriate selection of attachments for the desired application. WARNING: BEFORE INSTALLING BOWL SEAL AND ATTACHMENTS, BE SURE THE POWER CORD IS UNPLUGGED. Bowl Seal: Insert the black seal ring in the groove of the white seal retainer so the thin black edge is down and the tapered white part on the retainer is up (Fig. 2). Then install the seal onto the mot

Résumé du contenu de la page N° 5

OPERATION Move bowl tilt handle to HOLD to lock bowl in vertical position (Fig. 5). Close and latch the lid by grasping the lid handle with the left hand. Press lid handle down while turning the latch until lid lock is engaged (Fig. 5). CONTROLS (FIG. 5) The Timer has three mode settings: Run, Jog or Timer. RUN – Machine runs continuously after START is pushed until STOP is pressed. JOG – Machine jogs momentarily while START is held down; the machine turns off when you release START. TIMER –

Résumé du contenu de la page N° 6

BAFFLE HANDLE LOCK HANDLE LID HANDLE LID LATCH BAFFLE HANDLE START STOP LOCK HANDLE HAND KNOB 5-MINUTE TIMER WITH JOG, RUN, AND TIMED SETTINGS BOWL TILT HANDLE CUT MIX SHAFT ASSEMBLY KNEAD MIX SHAFT ASSEMBLY MIXING BAFFLE STRAINER BASKET LID SCRAPER PL-41654-1 Fig. 5 – 6 –

Résumé du contenu de la page N° 7

CLEANING CAUTION: Damage to the lid can result if it is exposed to certain chemicals. Do not use harsh abrasives, such as powdered or liquid cleansers, steel wool or other abrasive pads; cleaners containing ammonia, such as window sprays; cleaners containing chlorine, solvents, chemical adhesives; and highly caustic chemicals, such as drain cleaners or commercial dishwasher detergents. Prewash Before disassembling, put 1gallon of warm water and 1or 2 tablespoons of a mild liquid househo

Résumé du contenu de la page N° 8

MAINTENANCE The prelubricated motor bearings should be checked by a Hobart service technician every 3 to 4 years under normal use. No other lubrication is required. TROUBLESHOOTING SERVICE Contact your local Hobart-authorized Service Offi ce for any repairs or adjustments needed on this equipment. Symptom Possible Cause 1. Electrical power not connected. Cutter mixer won't operate. 2. Circuit breaker tripped or fuse blown. F34772 Rev. B (May 2007) – 8 – PRINTED IN U.S.A.