Instruction d'utilisation Panasonic WV-CP474H

Résumé du contenu de la page N° 1

FEATURES
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Color CCTV Camera
Dynamic range of 46 dB.
(3) Internal Line-locked Multiplex Vertical (VD2) Sync.
(4) Auto/Manual White Balance Function
Operating Instructions
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3.

Résumé du contenu de la page N° 2

Cautions: MOUNTING LENS/FOCUS ADJUSTMENT 1. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect the grounding lead to the GND terminal. 2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for Installation of Auto Iris Lens Connector the Input Terminal. Install the lens connector (YFE4191J100) when using a video drive ALC lens. 3. The connections should comply with National Electrical Code (NEC). (1) Cut the iris control cable at the edge of the

Résumé du contenu de la page N° 3

SETUP SETTING PROCEDURES 1. CAMERA SETUP MENU 1. Camera Identification (CAMERA ID) Setting This camera utilizes an on-screen user setup menu. You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor screen. • Opening the Setup Menu To edit the CAMERA ID Press and hold down SET for 2 seconds or 1. Move the cursor to CAMERA ID. more. Highlighted The

Résumé du contenu de la page N° 4

SETTING PROCEDURES 2-2. ALC Mode with SUPER-D2 OFF and ELC Mode 6. Synchronization Setting (SYNC) Note: If ELC is selected, set MASK SET according to this procedure. You can select internal sync (INT) mode, line-lock (LL) mode or the VD2 signal (multiplexed vertical drive signal) mode. 1. Move the cursor to SUPER-D2 and select OFF. (When you select ELC, 1. Move the cursor to SYNC and select LL or INT. ** ALC CONT ** SUPER-D2 is not available.) The MASK BACK LIGHT COMP The factory default se

Résumé du contenu de la page N° 5

4. When you want to adjust the white bal- 10-5. Chroma Phase (Hue) Setting (HUE) ** AWC ** ance manually, press R to select AWC 1. Move the cursor to HUE. R ....I.... and press SET. The AWC menu - + 2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust B ....I.... appears on the monitor screen. (When the hue (chroma phase) level. - + ATW is selected, pressing SET dis- 10-6 BW MASK SET plays

Résumé du contenu de la page N° 6

SPECIFICATIONS Pick-up Device: 771 (H) x 492 (V) pixels, Interline Transfer CCD Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube) Scanning: 525 lines/60 fields/30 frames Horizontal: 15.734 kHz Vertical: 59.94 Hz Synchronization: Internal, Line-locked or Multiplexed Vertical Drive (VD2) selectable Video Output: 1.0 V[p-p] NTSC composite 75 Ω /BNC connector Horizontal Resolution: 480 lines (C/L), 570 lines (B/W) Signal-to-Noise Ratio: 50 dB (Equivalent to AGC O