Руководство по эксплуатации Panasonic WV-CP474H

Краткое содержание страницы № 1

FEATURES
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Color CCTV Camera
Dynamic range of 46 dB.
(3) Internal Line-locked Multiplex Vertical (VD2) Sync.
(4) Auto/Manual White Balance Function
Operating Instructions
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3.

Краткое содержание страницы № 2

Cautions: MOUNTING LENS/FOCUS ADJUSTMENT 1. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect the grounding lead to the GND terminal. 2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for Installation of Auto Iris Lens Connector the Input Terminal. Install the lens connector (YFE4191J100) when using a video drive ALC lens. 3. The connections should comply with National Electrical Code (NEC). (1) Cut the iris control cable at the edge of the

Краткое содержание страницы № 3

SETUP SETTING PROCEDURES 1. CAMERA SETUP MENU 1. Camera Identification (CAMERA ID) Setting This camera utilizes an on-screen user setup menu. You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor screen. • Opening the Setup Menu To edit the CAMERA ID Press and hold down SET for 2 seconds or 1. Move the cursor to CAMERA ID. more. Highlighted The

Краткое содержание страницы № 4

SETTING PROCEDURES 2-2. ALC Mode with SUPER-D2 OFF and ELC Mode 6. Synchronization Setting (SYNC) Note: If ELC is selected, set MASK SET according to this procedure. You can select internal sync (INT) mode, line-lock (LL) mode or the VD2 signal (multiplexed vertical drive signal) mode. 1. Move the cursor to SUPER-D2 and select OFF. (When you select ELC, 1. Move the cursor to SYNC and select LL or INT. ** ALC CONT ** SUPER-D2 is not available.) The MASK BACK LIGHT COMP The factory default se

Краткое содержание страницы № 5

4. When you want to adjust the white bal- 10-5. Chroma Phase (Hue) Setting (HUE) ** AWC ** ance manually, press R to select AWC 1. Move the cursor to HUE. R ....I.... and press SET. The AWC menu - + 2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust B ....I.... appears on the monitor screen. (When the hue (chroma phase) level. - + ATW is selected, pressing SET dis- 10-6 BW MASK SET plays

Краткое содержание страницы № 6

SPECIFICATIONS Pick-up Device: 771 (H) x 492 (V) pixels, Interline Transfer CCD Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube) Scanning: 525 lines/60 fields/30 frames Horizontal: 15.734 kHz Vertical: 59.94 Hz Synchronization: Internal, Line-locked or Multiplexed Vertical Drive (VD2) selectable Video Output: 1.0 V[p-p] NTSC composite 75 Ω /BNC connector Horizontal Resolution: 480 lines (C/L), 570 lines (B/W) Signal-to-Noise Ratio: 50 dB (Equivalent to AGC O