Instruction d'utilisation Trane EXWA

Instruction d'utilisation pour le dispositif Trane EXWA

Dispositif: Trane EXWA
Catégorie: Pompe de chauffage
Fabricant: Trane
Dimension: 0.58 MB
Date d'addition: 9/18/2014
Nombre des pages: 31
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Trane EXWA. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Trane EXWA.

Pour votre confort

Si regarder l'instruction Trane EXWA directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Trane EXWA en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Trane EXWA sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Trane EXWA Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 31 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Trane EXWA - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Trane EXWA. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

Installation
Owner
Diagnostics
Water-to-Water
Water-Source Heat Pump
Models WPWD, GSWD and EXWA
Models
“A” and later Design Sequence
WPWD EXWA
024-072 – 60 HZ 240 – 60 HZ
GSWD
024-072 – 60 HZ
WSHP-SVX02A-EN

Résumé du contenu de la page N° 2

Notice NOTICE: Warnings and Cautions appear at appropriate sections throughout this manual. Read these carefully. WARNING -Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION -Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. CAUTION -Indicates a situation that may result in equipment or property-damage-only accidents.

Résumé du contenu de la page N° 3

Contents Installation/Startup/Commissioning 4 Pre-installation Checklist 4 5 General Information 6 Dimensions/Weights 10 Installation Instructions 19 Electrical Requirements 20 Pre-Startup Checklist 21 Startup/Commissioning 21 Sequence of Operation 22 Operating Pressures 30 24 Startup Checklist & Log 25 Maintenance 26 Warranty Information 28 Troubleshooting Checklist 29 Unit Wiring WSHP-SVX02A-EN 3

Résumé du contenu de la page N° 4

Pre-installation Checklist WARNING Fiberglass Wool! Product contains fiberglass wool. Disturbing the insulation in this product during installation, maintenance or repair will expose you to airborne particles of glass wool fibers and ceramic fibers known to the state of California to cause cancer through inhalation. Glass wool fibers may also cause respiratory, skin or eye irritation. Jobsite Inspection Always perform the following checks before accepting a unit: 1. Verify that the nameplat

Résumé du contenu de la page N° 5

General Information Unit Nameplate ton through 6-ton equipment, and at (which may be available for field use). The unit nameplate is located at the the power block for the 20-ton equip- See page 17 for diagnostic informa- front of the unit. It includes the unit ment. tion. model number, serial number, electri- Desuperheater All low voltage wiring is made at the cal characteristics, refrigerant charge, (Option for 2-ton through 6-ton units) unit’s low voltage terminal board. and other pertinen

Résumé du contenu de la page N° 6

Dimensions/Weights/ Clearance Table 1: Unit weights Shipping Shipping WARNING Size Weight Weight with pallet (lb) w/o pallet (lb) Improper Unit Lift! Test lift unit approximately 24 inches to verify proper 024 163 153 center of gravity lift point. To avoid dropping of unit, 036 183 173 reposition lifting point if unit is not level. Failure to properly lift unit could result in death or serious injury 042 203 193 or possible equipment or property-only damage. 048 214 204 060 244 234 072 27

Résumé du contenu de la page N° 7

Dimensions WPWD/GSWD 024-036 WSHP-SVX02A-EN 7

Résumé du contenu de la page N° 8

Dimensions WPWD/GSWD 042-072 8 WSHP-SVX02A-EN

Résumé du contenu de la page N° 9

Dimensions EXWA 240 WSHP-SVX02A-EN 9

Résumé du contenu de la page N° 10

Installation General Installation Checks WARNING The checklist below is a summary of Hazardous the steps required to successfully in- stall a unit. This checklist is intended to Voltage! acquaint the installing personnel with Disconnect all electric power, procedures required in the installation including remote disconnects process. It does not replace the de- before servicing. Follow proper lockout/tagout procedures to tailed instructions called out in the ap- ensure the power can not

Résumé du contenu de la page N° 11

Installation Water Connection WARNING Connect the source-side and load-side Improper Unit Lift! water-in/water-out from the water-to- Test lift unit approximately 24 water heat pump to the source system inches to verify proper center of and the load system. gravity lift point. To avoid Note: The source for a water-to-water dropping of unit, reposition lifting point if unit is not level. Failure to heat pump is typically a boiler/cooling properly lift unit could result in tower or geoth

Résumé du contenu de la page N° 12

Installation Cleaning and Flushing bled off. Note: Vents should be open when the the Water Loop (3) With the air vented and the water pumps and supplementary heat sys- After the piping system is complete, circulating, the entire system tem are shut down. the flexible hose connectors should be should be checked for leaks with re- doubled back to complete the water pairs made as required. Figure 4: Flushing water loop circuit external to the unit (avoiding (4) Operate the supplementary trash set

Résumé du contenu de la page N° 13

Installation Supply/Return Pipe Connections (3) The water lines should be routed to the Loop Pump Kit not to interfere with access to the unit. (1) Connect the supply and return hos- The use of a short length of high pres- es to the water-inlet (from supply) and sure hose with the swivel fitting may water-outlet (to return) of the unit. The simplify the connections and prevent rubber gaskets for the water-in and vibration. Pressure/Temperature (P/T) water-out connections are located in port

Résumé du contenu de la page N° 14

Installation Water Heater Hook-up (option) Figure 8: Water heater kit Instructions for connection from the desuperheater (option) water-in/out to the domestic hot water heater may be found in WSHPC-IN-4 or 72-9006-02. This water heater kit (Figure 8) ships in all units with the desuperheater op- tion. The kit is zip tied to the compres- sor base; and consists of piping connections and shut-off valve. For units containing the desuperheat- er option, the desuperheater pump fuse is located w

Résumé du contenu de la page N° 15

Installation Filling the Loop Pump Kit System Once the loop, pump module and unit are fully connected, the system will need to be filled with water or water/ antifreeze solution. See Page 14 for an- tifreeze/water mixture by volume. Fill both sides of the outside portion of the loop first via the pump module. The hose kit and unit should be filled last after purging of the ground loop is complete. To fill the outside loop; (1) attach a water hose to the 1-inch FPT brass valve ports loca

Résumé du contenu de la page N° 16

Installation Power Wiring Field Installed Power Wiring The high voltage connection is made Power wiring to the equipment must at the 1TB1 terminal block for the 20- conform to National and Local Electric ton equipment, and at 1K1 for the 2- Codes (NEC) by a professional electri- ton through 6-ton equipment. The ter- cian. minal block or contactor is located in- side the unit control box. Refer to the customer connection diagram that is WARNING shipped with the unit for specific ter- mination

Résumé du contenu de la page N° 17

Installation Low Voltage Wiring Controls Using 24 VAC Before installing any wire, refer to the electrical access locations on the unit submittals located on pages 7 through 9. Ensure that the AC control wiring be- tween the controls and the unit’s ter- mination point does not exceed three (3) ohms/conductor for the length of the run. Note: Resistance in excess of 3-ohms per conductor may cause component failure due to insufficient AC voltage supply. Figure 9: Low voltage connection Chec

Résumé du contenu de la page N° 18

Installation Changing Freezestat or Low Pres- (2) A unit with a 20°F freezestat is go- the old low pressure cutout to the new sure Cutout Switches ing to be put on an open well system low pressure cutout. (WPWD/GSWD models ONLY) or a closed loop system with NO anti- Identifying the Low Pressure Cutouts Each unit has two factory installed low freeze solution. By definition, the unit The 7 psig low pressure cutout is used pressure cutout switches and one must have a 35°F freezestat installed w

Résumé du contenu de la page N° 19

Electrical Requirements Table E-1: Electrical performance WPWD/EXWA Model/MBH VOLTS-AC/HZ/PH Min. Max Compressor LRA No. Without Desup With Desup Util. Util. Each of MCA Max Desup MCA Max Volt Volt RLA Comp Fuse RLA Fuse WPWD024 208-230/60/1 197 253 11.4 56.0 1 14.3 25 0.4 14.7 25 220-240/50/1 198 264 9.6 47.0 1 12.0 20 0.4 12.4 20 265/60/1 239 292 9.6 47.0 1 12.0 20 0.4 12.4 20 WPWD036 208-230/60/1 197 253 15.0 73.0 1 18.8 30 0.4 19.2 30 208-230/60/3 197 253 10.7 63.0 1 13.4 20 0.4 13.8 20 220-

Résumé du contenu de la page N° 20

Pre-Start Checklist Pre-Start-up Checklist Before energizing the unit, the following system devices must be checked: ____ Is the high voltage power supply correct and in accordance with the nameplate ratings? ____ Is the field wiring and circuit protection the correct size? ____ Is the low voltage control circuit wiring correct per the unit wiring diagram? ____ Is the piping system clean/complete and correct? (A recommendation of all system flushing of debris from the water- to-refrigerant h


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Trane 22-5202-03-3605 Manuel d'utilisation Pompe de chauffage 0
2 Trane 2TWB0-UM-2 Manuel d'utilisation Pompe de chauffage 0
3 Trane 4TWX6 Manuel d'utilisation Pompe de chauffage 1
4 Trane 2TWB-SVU01A-EN Manuel d'utilisation Pompe de chauffage 1
5 Trane 4TWX6036B Manuel d'utilisation Pompe de chauffage 2
6 Trane 4TWX6048B Manuel d'utilisation Pompe de chauffage 1
7 Trane 4TWX606OB Manuel d'utilisation Pompe de chauffage 0
8 Trane 4TWX6024B Manuel d'utilisation Pompe de chauffage 0
9 Trane 4YCY4024A Manuel d'utilisation Pompe de chauffage 5
10 Trane 4YCY4060A Manuel d'utilisation Pompe de chauffage 0
11 Trane GETB Manuel d'utilisation Pompe de chauffage 2
12 Trane GEH Manuel d'utilisation Pompe de chauffage 27
13 Trane GEV Manuel d'utilisation Pompe de chauffage 3
14 Trane GSWD Manuel d'utilisation Pompe de chauffage 0
15 Trane PKGP-PRC003-EN Manuel d'utilisation Pompe de chauffage 1
16 Edelbrock 15005 Manuel d'utilisation Pompe de chauffage 0
17 A.O. Smith AH Manuel d'utilisation Pompe de chauffage 2
18 ACS 882.00217.00 Manuel d'utilisation Pompe de chauffage 1
19 A.O. Smith AHD 290 Manuel d'utilisation Pompe de chauffage 3
20 AC International SELF-PRIMING CENTRIFUGAL PUMPS Manuel d'utilisation Pompe de chauffage 5